FX Maverick, FX AMP regulator reseal & reassembly

[@Fernando_Woolybooger]

I really wish you would do a short video going into detail about the washer stack arrangement. Still a little confused about that step. Thanks!

[@jorgeboehme7368]

Hi Sir. Can You please show or make a video of how to setup de Maverick to work with only de bottle adaptador regulator?? In order to hace a bigger plenum. Thanks

[@DocMustafa]

Hello Mr. Rowe. I have a suggestion for when you’re taking out the o-rings from the reg adjustment screw and from the regulator housing (10x1.5)…it’s a million times easier if you use a sewing needle instead of flattening your pick or using needle nose pliers like at 4:52. Since you’re replacing them, you might as well poke it and insert the need horizontally into the o-ring. Removing it becomes so much easier. Just a trick I use that I thought I’d share. Awesome guide!

[@ernestrowe5061]

Nice one!

[@nickch96]

@@ernestrowe5061 we would like a video, showing off this custom maverick.

[@marcioeidelwein7610]

​@@ernestrowe5061 What kind of material did you use on the tip of the disc springs pin, where does the sealing with the adjustment screw?

[@realspringer]

Earnest....a tip from the laziest bastard on the planet.(or just an old toolmaker)..run over to the lathe turn up a piece of delron or nylon to slide up inside the reg body from the opposite side......has to be flush with the "bottom of o-ring groove ) for (4x1.5 -nbr 70 or 90) depending on which parts list your looking at....lol....NO MORE FIGHTING IT....Slides right in.....WITHOUT pokin it with allen key....push mine in with a finger......Now..I think that tip deserves an EXTRA lump a coal in my christmas sock...dont you...Santa..lol...lov the vids man....

[@franciscocarvalho2424]

Show só falta encontrar o gênio aqui no Brasil KKK sempre desejando muito mais sucesso de um fã seu é do seu trabalho só possou desejar se pode-se daria mais like garantido sempre

[@brokosok]

Earnest where did you get the Arca rail for the Maverick? Please help me I’ve been looking for one.

[@ashishchoudhary269]

HI ernest Thanx for your advice , i could get the same , i issue i am facing now is that there is a leakage of air from the vent hole in the plenum cylinder (opposite side of the 2nd regulator), and as soon as i put the bottle the leakage starts . i seek your advice onto which of the O rings may have been busted, look forward to your reply, thanx

[@mikecarter4412]

Hey Ernest great video. My Mav had an extra o ring on the regulator adjustment screw right under the threads. Normal? It’s never been apart and I bought it new.

[@KrakkenZero]

does it look like theres three orings? there should only be 2

[@jozefsimo4219]

Hi, great video. I have a problem. When the regulators are fully open, I have a maximum pressure value of 120 BAR. Why can't a higher pressure value be set?

[@mrdee423]

Hey Ernest, Tried removing the o-ring inside the adapter and failed miserably! And idea who has one in stock new or used . When I screw the bottle on , the air just shoots out the atmosphere hole. Ty

[@ssmayassmaya6030]

what bad rider is that where can i get same setup … do you work on mavericks with power problems ??

[@KevinDeCaesar]

Where do you get the tool that removes the washers.

[@pliashmuldba]

Just changed low pressure ( #2 ) on my maverick, but the damn thing loose pressure thru the venting hole, there are no reg creep, regulated shooting pressure remain 100 bar i set it to, even when bottle are empty over night.

[@mikedavis4039]

Hi Earnest I recently removed my AMP regulator on my maverick due to a damaged bottle adapter. But as I found out the schematic for the parts is the same as the dream line Drawing F10101. It states on the drawing that the there are 2 different Belleville washers. Washer 10x4, 2x .06 and washer 10x4, 2x .05. I am not sure in which order these are supposed to be stacked and if it makes any difference.

[@ernestrowe5061]

As long you have enough reg pressure any stack configuration will do.

[@alaireconguerre2048]

Super !

[@ssmayassmaya6030]

What size is the O rings on the adjuster mine are bad and can't find nothing that small

[@ashishchoudhary269]

hi great video , i have question regrading refresh rate , within what time(seconds) does the refill happen to set pressure post firing a shot , thanx

[@ernestrowe5061]

There is a test for that before adjusting anything, document the speed between timed shots for example, take five shots three seconds apart and document all the speed, then 4 seconds apart, then 5 seconds apart and so on till 10 seconds apart, now u can see the refresh rate of the current setup

[@Douger318]

You make it look easy but it’s not bad once you done it few times

[@ernestrowe5061]

Any one that disassemble hundreds of regulators can make it look easy 😊

[@DalMiranda3]

The reg piston is an upgrade to the Delrin one used in previous models? If so, would it be available for Gen one impact with a shorter piston (14mm)?

[@ernestrowe5061]

No, haven’t seen a brass 14mm piston

[@fieldpro5041]

awesome video as always brother. when are you coming back up to shoot

[@ernestrowe5061]

Hi Norm, man still trying to got Rick to come-seems like we all busy for now😂

[@fieldpro5041]

@@ernestrowe5061 I hear you buddy. we have to get together soon even if its just for dinner brother

[@okhouri]

Where did he put the thickest spring washer? Is it me or does he just ramble ...

[@volcom84bait]

Where can I get that tool to put all the plate?? Any site??

[@ernestrowe5061]

At: 910airguntuningandrepairsllc.com

[@alessandrofae2621]

what are the gains in removing the second regulator?

[@ernestrowe5061]

More plenum volume of 160cc, with 2nd reg 56cc plenum. 160cc plenum more power, lower ES, more shots

[@sash9490]

So make a video about that, How to - Maverick with only one regulator ?!

[@nickch96]

Easy, you buy a plenum tube and you put it on the front of the existing plenum and now you have double the volume 164 cc

[@Douger318]

So does the factory know this lol.

[@ernestrowe5061]

Know what?? The spring thickness?? If so when you remove the spring washer measure the thickness- the thickness are mix matches, to get factor settings, some set are two different thickness and some same thickness- so measure your combination of sizes for reference to reassemble. Its one Method to set a spring washers strength.

[@DocMustafa]

@@ernestrowe5061 I think he means does the factory know you’re putting your Maverick on steroids lol. I would assume they do.

[@ernestrowe5061]

@@DocMustafa --> everyone knows i don’t ishoot stock AG 😊

[@pisa_sombras9281]

Hola ... tengo una fx maverick spinner ... Si eres tan amable me gustaría que me dijeras donde puedo conseguir el util extractor de la válbula ... un saludo