Garage Door Installation - Demonstration (Full Tutorial Below)

[@UlyssesContreras-yn1gh]

I have my own garage door business and have landed every job thanks to god

[@brayanmartinez6397]

Need to tell you that now I can sleep better at night after 2 years thinking how to fix my door . I did today in 2 hours thank you so much and God bless you

[@andresmadore3874]

This me now l just buy my own house and I don’t know how put my garage door but l just this one so now I going to do the other one is easy to that

[@HMPRODIGY]

Sheessh my man flexing his dough on us lol

[@patricksimon3951]

Great tutorial, I work for Arbon Equipment, and let me say this, I'll never make as much money as you are. Thanks again for another great video!!

[@jeremiedubuc5657]

I use to pre assemble my two tracks together then put the first panel and then screw one of my track to the wall so the panels will be hold by the track and when all my panel are installed I make sure my door is level and I will take the distance between the top of the door and the shaft bearing to make sure both tracks are at the same height it is crucial if you want a door that lift level all the way up and down

[@Mocking_Beard]

Always with the selling of the courses/classes

[@SledgeHammer43]

Use a level to make sure your top track is level. That will decrease the ware on your garage door opener. Also make sure your track is parallel or your door will get wedged or it may fall out of your track and on anything under it.

[@jr_NorCal]

Big profit! I had zero experience and makn good money but lots of OT

[@donmulvey9280]

Also, would you attach new tracks to old track mounts? Seems like it would save a step to reuse them .

[@brianstrauch8574]

Sitting there in a Mercedes with cash in your hand is so cringe. That made it feel like those get Rich quick commercials you would see at midnight. Yet I found everything else you said worthwhile.

[@mobiledevto]

Don't hate the player, hate the game. Go out there and get your share of the pie and stop wasting your life complaining about how life is unfair. Yeah life is unfair you can't change that. Now go get you some and improve the lives of your children.

[@johncameron6864]

Where is the Mercedes?

[@BereanFellowship]

Do you still need to use the torque spring if you're using the garage door opener?

[@donmulvey9280]

Nice! However, I missed how you got those vertical tracks over the wheels you had already installed. Do the vertical tracks have enough clearance to wiggle over the wheels?

[@ElPasoTom]

The garage door install was great, very informative. Showing cash was just a low class move though.

[@donmulvey9280]

Lastly, do you have a video about how to attach the cables to the ends of the spring rod? Great video but looking for just a bit more detail.

[@ironjohn5914]

I install my own garage doors and for customers too, it's a lot of work, but fun too.

[@dianebowman2362]

Can I use the existing metal tract that seems to be in fine condition, or must I take it down and install the new tract that comes with the doors?

[@mtnbikerva1]

I live in the midatlantic. Is there a best brand or model garage door company or model that is not for people that make 500k or more a year? Is a steel the best quality/strength/durability/non rust... Or do some brands and models very greatly? I need 2 smaller/normal garage doors. Opener quality? Clear winner and looser/crap? Thank you.

[@Jennifer-xw7dw]

What is the best standard garage door for florida that's hurricane rated?

[@lbsr3614]

Qnd spring sizes are they all different it seems they are thanks

[@dtp-frostyyy4633]

Yes they are you have different aize springs for different weighted doors for example here in Florida we have one door just a standard Clopay w3 door gets 5 struts and 234 size springs which are slightly smaller then we have a Clopay w5 and that gets 8 struts and a 243 and 250 spring because it's heavier. (Struts) bar across the panel to help with the amount of wind it can withstand in Florida depending on where you live you may not get struts or have to use them

[@DickGraysonRebirth]

Thanks for the information sir. Much appreciated 👍🏾

[@Hadfield420]

Im here because i just started working in a garge door warehouse and would like to learn the parts and how they go together

[@murd777]

Can I install a 7ft tall garage door on a 8ft track?

[@thee4683]

Definitely but will need the correct springs for it to work properly!

[@josephmercuri2902]

Did you miss the step of attaching the cables on the side of the doors to the spring assembly

[@MacAroma-v7w]

How to apply to you I know how too install garage door?

[@isinet2813]

Hi and thanks for this video. I'm intrigued because I too never thought about garage doors. But everything you've said makes sense! How do I get the discount coupon for the course? I don't see the link?

[@GarageDoorTrainingSchool]

That’s great to hear, thank you! The coupon you’re referring to was actually an old promotion, so this particular discount is no longer offered. But you can book a call with us to ask about our latest promos and discounts! Book a Call Here: calendly.com/garagedoortraining/schedule-a-call?month=2023-01

[@Beamin-vt7jm]

Our doors don’t have the middle piece for the track. Why is that? Is that common?

[@vc8424]

“First you do this, than you do that” great explanations bro

[@GarageDoorTrainingSchool]

This video is not meant to teach the installation. We have in-depth garage door installations lessons on our course 👍

[@heroknaderi]

This video was very helpful. I am thinking about getting into this trade also for a bonus do swing out garage doors too. And gates. I appreciate your time. I enjoyed the video.😎😎

[@SilverSparrow5]

Tips on fixing gap in the top of the door? A lot of times we install, the very top panel won’t be fully seated and closed against the opening, leaving a gap and we never know how to fix the problem.

[@bigal4587]

You should take the course because there are several ways you can accomplish this. After taking the course and learning the correct way I’m sure you will not run into this issue in the future! You can sign up at www.garagedoortrainingschool.com

[@Mr.Pickles64]

All you need to do is loosen the two set screws that hold the top fixtures and while pushing the door to the wall pull the bracket that holds the very top roller towards yourself until it can’t adjust further and then tighten the two set screws. Do that on both sides and the door will seal better at the top. Also you could just put residential trim around the outside of the door, so you block the majority of the sunlight from leaking through.

[@JerryHoover-e2q]

You need to show more details about each item you use.

[@piopacheco2998]

Do you tighten the springs before you install completely the side cables? or after, you didn't say.

[@msmalsaleh4738]

Where step by step?

[@GarageDoorTrainingSchool]

On our course in the description 👍

[@sunnienie239]

How much the garage look like this cost ?

[@GarageDoorTrainingSchool]

What city and State are you in?

[@sunnienie239]

the garage door that need to replace is in san diego '92115

[@vierka5967]

Love it! Especially the wads of cash in the tool bag. Reminds me of the Sopranos.

[@GarageDoorTrainingSchool]

Thanks, Vierka! We appreciate the positive feedback 👍

[@lbsr3614]

Hi I want to pay for this course do you show all needed for garage door fix like fixing door opener I see in your price list a crooked door that's stuck and more on your price list you have prices on fixing garage door opener just curious very interested in this thanks

[@terencescott3957]

When you start flashing money like a rapper my radar went up. Why is he flashing money? Here comes the catch.

[@angelofjustice913]

what size and lengthened of torsions spring do you use?

[@GarageDoorTrainingSchool]

It depends on the door type, height, and weight.

[@skidmoro9642]

toe nail is old school...Wayne Dalton with whiz nuts on track and real torsion system ....interesting

[@RyanBrown-fp3vk]

Now hiring. Willing to train. Sw washington

[@garagedoordoctorofhouston6518]

Good job

[@GarageDoorTrainingSchool]

Thanks!

[@CelestinoFigueroa3]

You are a good men !!!

[@JamesCouch777]

Good enough 👍

[@leea3531]

You’re awesome for this info

[@GarageDoorTrainingSchool]

Thanks, Lee!

[@jramlal5782]

You forgot to show how to program the remote

[@sosgds]

Wow! This is huge opportunity! In your course what do you cover? Is it just the Wayne Dalton brand? Is it just the 9100 model door?

[@GarageDoorTrainingSchool]

We cover a variety of different manufactures within our course, but Wayne Dalton is one of the more common companies we work with.

[@lancesiona]

Wayne dalton is a shitty brand

[@notaustinbro402]

Wayne dalton is legit trash

[@stevennhlapho8826]

Interesting

[@jonforsythe374]

FYI. I just put a new door on a rental. It is a 16' wide by 7' tall door. 4 panel. Total cost was $1785. Home Depot sells the door for $1098. There would be $88 in tax which leaves $599 in labor. Much less than the $1000's promised. Just another side. Phoenix, Arizona job.

[@GarageDoorTrainingSchool]

Home Depot upsells their doors, it’s better to go straight to the manufacturer. People in this business often under value the labor when it’s possible to make a lot more, because it’s a niche skill that not a lot of people know how to do.

[@GarageDoorTrainingSchool]

Those are junk

[@bigpermsgarage6290]

I've been installing doors since 2000 and I'd never tighten a drum on a hollow shaft with an impact, just saying.

[@naeemalam5172]

I need joob I'm completely tecnition pleez joob now Saudi Arabia working atomic dors

[@dtp-frostyyy4633]

Should most likely learn the spell correctly first.

[@GarageDoorTrainingSchool]

You can learn garage door services and installations in our online course. Below is the link to our home page. Hope this helps! courses.garagedoortrainingschool.com/

[@jumaniaccessories6538]

Hi

[@jumaniaccessories6538]

I’m from Dubai I don’t know anything please know this work sir

[@GarageDoorTrainingSchool]

You can learn this type of work with our course here: courses.garagedoortrainingschool.com/bundles/garage-door-technician-certification-course

[@DadOutdoors]

Why are you carrying all that cash around? Seems very strange, and ill-advised.

[@austinmattox2889]

Why don’t you show some real door big commercial doors

[@bigal4587]

We don’t do commercial doors or train people on them either so why would we show them?

[@dc6233]

Even a nice door is 1500$, to charge people 5000$ makes this just like any other trade, lucrative. But, it's probably the easiest trade out there, try being an electrician, a plumber or an HVAC guy, there's far more involved in those trades. Imagine poor weather conditions, garage doors are in the garage, where are plumbing, electrical or HVAC units installed?? In crawl spaces, attics, under the house; imagine it being 15 or 150 degrees (attics) in those spaces, not so fun...

[@seanbrick2886]

I wouldn’t say it’s easy

[@svetislavmi]

Putting up garage door requires no skill at all. Okay. So quit acting like it’s a rocket science because it’s not.

[@GarageDoorTrainingSchool]

We try to highlight how easy the trade is to learn and start working in. Nobody said it’s rocket science 👍

[@bibmitchell6542]

Those doors are flimsy, straight-up garbage

[@GarageDoorTrainingSchool]

It’s what the customer ordered 👍

[@ShiCherry-i1d]

If you need to customize the aluminum alloy /pvc high speed spiral door, please feel free to contact me, I can customize any product for you