Geekpure RO5 5stage Reverse Osmosis Water Filtration System Installation

[@pavelreact828]

Just bought it yesterday, and it has a new type of tank valve..😮

[@muckbringer]

I wasted a day trying to hook this up. After many promises to return it I had it set so decided to try it out. Water bursting out of 1st filter. Im returning it and might classify it as the worst item I have ever bought. Ill spend the extra couple bucks for an easy installation and the extra room. Hope they enjoy the mess they're getting back.

[@Samhizawa]

Please show us how to connect uv for model RO5-UV

[@scottmccormick2138]

Good job. I hung my filter housing. I like the light under the sink. What about the sanitizing step?

[@alexv2053]

After setup, filtered water flows normally for a minute before the flow rate becomes dismal and the waste water has a higher flow rate. The filtered water is also more acidic than the waste water, is this how it's supposed to be?

[@OpusBuddly]

I installed it in the basement for ease of installation and servicing and ran the finished RO water line upstairs to the sink.

[@10Briguy]

I'm doing the same thing, Today actually. Underneath the sink just has no working room. SO MUCH easier putting it directly below the sink in the basement.

[@alexv2053]

How come you wrote "turn off tank valve before flushing" but you turn the valve into the ON position?

[@mustaphazaaboul6649]

How is ot working without a pump It will waste a lot of water to purify ????

[@degerlicocuk626]

Bu güzel video için çok teşekkürler. Çok yararlı. Thank you very much...

[@krishaky]

While the manual does need a few updates. Fairly easy installation. Do I need the flow restrictor? The flow restrictor that goes into the drain does not fit the red tubing. Thank you

[@nortonnorth1371]

Can't disconnect the tube from the filter like shown in 2:20. Removed the blue piece, but the tube does not pull out. Am I missing something?

[@nortonnorth1371]

OK, got it. To disconnect the tube, push up on the little while plastic ring while pulling out the tube.

[@artvandeleah9952]

I bought this type of system from geek pure. The RO tank was about 1 gallon. We bought a 5 gallon ( 4 gallon full water potential) tank, but it ONLY fills 1 GALLON at a time. What would i need to correct so the system can fill 4 gallons water INSTEAD of 1 gallon currently? Thank you for any help 🙏

[@12riveradavid]

Can this be installed in the basement? Its just below the kitchen where it would be installed

[@ecomech7464]

if it leaks hose between filters hose is cut to long fixed by putting loop of hose takes pressure off push in fittings

[@Serve_one_another_with_love]

Why the waste water line continously flowing for hours even when the tank is full and when the faucet is close?

[@eveningstar1]

Every connection is leaking!! Including ones I didn’t put a pipe in.

[@paulhelm2323]

The filter on top that he puts in at 2:30. Is there a wrapper that needs to be removed or do you just put it in like he showed with the blue plastic still on it? Thanks

[@thomasbaucus9029]

My TDS is 181?? Brand new filters. Why?

[@omargdottin]

How can I add the ph filter on this system ???any tutorial about connections?

[@viciousv4966]

The water saddle sucks, it comes with parts that aren’t used. This would be an easy installation if it worked propert

[@sohrabkarimian6574]

Couldn't this person talk and not just play some song? My god some companies don't care about customer satisfaction at all. I've read many negative comments about installation. I've installed other filters before and I see this product's booklet is so vague.

[@bevisprince4404]

Hello I purchased my Geek Pure 8 months ago and changed my Filters, the canisters won’t stop leaking….I’ve left several email messages with company. They haven’t responded back in anyway!!! Is there a phone number to speak with a person?!

[@BillyJoe71]

Your gaskets probably came out. The little black rings.

[@oskarv7024]

Apply petroleum jelly generously to canisters thread and gaskets. One pf my canisters leaked initially but stopped after me doing so.

[@patrickthomas3835]

Why does the waste continue to flow after using for a long time ?

[@Killerbeez1994]

The RO filter is replenishing the water reservoir so it continues to separate the clean water from the RO membrane until the reservoir is full again.

[@IOXY3]

Good for saltwater aquariums?

[@geekpurewatergroup9975]

yes,sure.

[@SaltCreep45]

6 Stage pushing 43 TDS and PH10 running 5 hours now if i dont see 3 Tds its going back ASAP

[@geekpurewatergroup9975]

thanks,but it depend on the feed water quality.and i'd like to share more about TDS value.in fact,43ppm is good value. whatever you test the water from the 4th stage membrane or the last stage.. i am sure if will be less and less in the future. 1. If you want to test water quality,it is best to test the water after membrane,that is the 4th stage.the 5th stage is post carbon filter ,it is not 100%pure ,so,TDS will be higher a little. but that is not bad matter,so,please don't mind. 2.TDS value is sensitive. if the water is hot or flowing, the TDS will be higher . even same water, if you put it there one day. the value will be different too. 3.if the feed water low TDS,the rejection rate is not so high as normal. if feed water is 300ppm, the output TDS is around 20 or 30ppm, if 500ppm water, the output is still 30ppm, your water just 43ppm, the output is same, but for these 3types feed water, the rejection rate is different. 4. as i said yesterday, even feed water 43ppm,output 40ppm, the water taste is big different.it is totally different. 5.if filtered water stocked in the filter or tank some hours, the TDS will be higher than usual. if you test the water quality,please drain it 1 minute before you test it. 6.43ppm is good value, in fact, in some area and countries, people mix some prefiltered water in RO water and keep TDS around 50-100ppm. they think there is enough mineral goods and better for our health.that is reason some people need the 6 stage. if you need further support,please get in touch with us.we will do our best to support you.

[@geekpurewatergroup9975]

yes,different feed water quality, the pure water TDS is different. the rejection rate will be 95% min.

[@harjotdhillon5143]

Thx for the vid

[@scotts.8967]

Can't Sanitize the Quick Change System!!

[@theblogofsingh]

where does waste water go?

[@SaltCreep45]

Down the drain or save it for the washing machine and mop floors

[@geekpurewatergroup9975]

the waste will be drain.

[@iamLI3]

coolthanks

[@vinhdoan2012]

The waste drain water drain at all time? it seem to waste a lot of water

[@BillyJoe71]

When you make a gallon you get 2 gallons of waste.

[@bradhogan9566]

Good job. The written instructions were crap

[@61mab]

Nice info, needs a bit of language usage work as per "Enlarge lifetime" to increase lifetime and "To protect" vs "for protecting" granted I have no other language to boast about or make snide remarks about. I'm watching a 12/17' and this is 20' so.......To protect vs for protecting

[@bradjacobson9152]

The music is killing me

[@oscargu4095]

muy mal explicado

[@SirValak]

This video has some really bad issues and having a hard time trying to load it. It won't play. Everything else on KZbin works perfect except this video

[@iamLI3]

no problems with the vid here o:

[@BillyJoe71]

Not an issue here as well.

[@forsakenoutcast]

This looks way too complicated for the average person no?

[@BillyJoe71]

Nah it's pretty easy honestly. Hire a plumber if you don't wanna try it.

[@10Briguy]

I'm almost complete at the moment, it's not bad at all.