what lathe should I buy?

[@notbadsteve]

Thanks. I'm new to the hobby. Started watching turning videos about 2 years ago to help with insomnia (not an insult)😂. I became obsessed and now want my own set up. I found this video after watching hundreds of adverts disguised as reviews. Yours was no nonsense and told me everything I needed to know. Cheers

[@user-uj1pz4xy5d]

well it's a lathe kzbin.infoUgkxN9zrzkkhnjUF5PQbuA_B1gYdsfCu9k6z but it wasn't what i would have anticipated. Headstock, tailstock, carriage apron are manufactured from aluminum now not cast iron. The spindle diameter for the bearings is too small allowing for a few play in the spindle so I am using some blue Loctite to take out the play.

[@JamesCouch777]

The best advice I would give to beginning turners is to buy a used lathe cheap to see if you want to continue turning or not. If you do then get the lathe you want and if not you don't have much invested.

[@Geiserwoodturner]

Good advice

[@notbadsteve]

Being brand new to the hobby, I'm edging towards used, purely down to budget. The only thing that worries me is I wouldn't know if I was being sold a lemon. Would you consider doing a video on what to look for when buying used? Or point me in the right direction. Cheers.

[@writingraven]

Excellent video and coverage.

[@bnelson313braveheart]

Very helpful information. Thank you!

[@sascani333]

Nice job!!

[@jimhood1202]

Great information. Thanks.

[@Geiserwoodturner]

You bet! Thanks for watching!

[@nkosiakinlabi3135]

This has been thus far the best and most detailed of any video I’ve watched explaining the in and outs of choosing a lathe. Thank you!

[@Geiserwoodturner]

Thanks!

[@rayjames6187]

Had to break out the pen lol

[@rayjames6187]

No, thank you.

[@johnkelly1027]

Very good advice,

[@Geiserwoodturner]

Thank you 😊

[@joekirk167]

I have a Harbor Fretght and I love it

[@Geiserwoodturner]

I know lots that love harbor freight lathes! Great!

[@johnriggenbach2999]

GREAT JOB...THANKS...

[@PucketyCrik]

Very clear simple advice. Thanks

[@foxfarms3669]

Excellent and informative video. Thank you. I subscribed.

[@Geiserwoodturner]

Glad you liked it! Thanks for subscribing!

[@georgebollinger7835]

I'm 68 years old and retired. Thinking about buying a lathe for turning pots for turkey calls. Pretty overwhelmed on everything I need. The Grizzly T25920 looks like a good unit but tooling components has me confused on what all I need. Very good video, thankyou and I will keep being a sponge soaking up information.

[@RexKrueger]

This is a really good video. Lots of information; no too long.

[@Geiserwoodturner]

Thanks so much!

[@ginoasci2876]

choose a lathe depending on what you’ll use it for and how often.

[@chrisperry3525]

BEST 'intro to lathes' video I've seen! Thank you.

[@Geiserwoodturner]

Thanks! I hope it was helpful!

[@enashdigal9274]

Nice. From India

[@mpace58]

Just took a wood turning class yesterday. Now I'm looking for my first lathe. Thanks for pointing out the things to look for and some specifications.

[@mingshengliu4661]

Detailed and helpful, thank you for sharing.

[@Geiserwoodturner]

Thanks for watching!

[@BrendansReasons]

lots of great information. thanks a lot

[@rudygowy9981]

Best review i have ever seen, grazie mille for that

[@geneclifford8662]

I am thinking about buying a wood lathe. Thanks so much for your time explaining the options. Happy turning.

[@BigGuyReviews]

Very nicely done, sir. The information you said you would provide, plus some. No BS. Nice video!

[@solodiver007]

Excellent informative video in a week where I'm shopping for my first wood lathe.

[@SBSPilot]

Excellent video! It has been a good help when deciding which lathe to buy. Would it be possible with a shopping guide for woodturning tools too? Perhaps showing the difference between cheap and expensive tools, the pros and cons of buying a set of tools, which ones to buy first if not buying a set? I think I wouldn't be alone wishing for such a guide without the sales pitch. 🙂 (I'm not sure I use the correct terminology, but with "woodturning tools" I mean the gouges, chisels, etc that are used when woodturning.)

[@Geiserwoodturner]

Thanks so much! A guide to buying woodturning tools would be a great idea! Yes You are using the correct terminology. I call them turning tools but I have heard them called Chisels, gouges, and knives ext. Which tools to buy first is also a great video idea. I’ll get working on videos, but just as a thought my top three would be a spindle roughing gouge, a 3/8” spindle gouge, and a parting tool. If you plan on making bowls a 1/2” bowl gouge would be a great starter as well.

[@joeysampaolo8962]

Thank you. Very informative

[@Geiserwoodturner]

Thanks so much!

[@teresas683]

Super helpful! Thanks! Sorry to see you don’t do many new videos…I get it, they are a lot of work. Appreciate the ones you have and you are a super teacher🙌🏻

[@lmallard3788]

Helpful advice. Thanx

[@johnbauby6612]

I have been woodworking forever and had never turned on a lathe. I was NOT going to drop upwards of $2000 on a lathe not having any idea if I would even like it. I opted for a Delta. I think it's called a "midi". Couldn't be happier. Under $1000, handles most everything I wanted to do to learn and fits in my tiny space available. It of course has its' limitations but the quality was very good for the price. Now, two years later I am ready for a full size lathe but have no plans of getting rid of my Delta. FYI, it is a new Delta, not an old school Delta which I would have preferred. Now I am ready to drop $2k, maybe even $3k on a decent full size lathe. I wish I had gotten into turning decades ago. Fun and practical.

[@Geiserwoodturner]

Great! Woodturning hooks ya! I wish you well in your search for a bigger lathe! 😀

[@johnbauby6612]

The question is which bigger lathe!? Your video was a good one and showed every single available option out there for lathes in general but I don't think I saw a l preference towards one or the other. In my search I "think" Laguna offers the most bang for buck? I was looking at the 18/36. I have a few Powermatic tools and they have been great but not cheap. I may go that route if I am able. No one wants to make such a large investment and find out their 600 pound, $4k lathe is not up to the task. Rather than getting a lathe that already has everything on it it may be more prudent to buy one with upgradability and add things on as time goes on and the need arises for other features.@@Geiserwoodturner

[@Geiserwoodturner]

@@johnbauby6612I think if I was to recommend something it would be Powermatic. It is a bit more $ though. My experience with my Laguna lathe is that it is adequate. I’ve had the chance to upgrade more than once and have not however. Over the years I’ve worked through most of the quirks and problems and I’m satisfied with my 18/36. It does what I need it to do and that is what counts. If I were to upgrade it would be to a Vicmarc or Robust lathe, but they are high end and pricey. So I guess in summary Laguna is adequate and a good value for the money but you may have tool rest banjo and possible electronics issues. I’ve heard good and bad about customer service. Powermatic is a great machine, more expensive. I’ve heard that they have less problems but can have some. I’ve heard they have great customer service. I hope this helps some. 😊

[@DrThunder88]

Detailed, yet succinct. Very nice video!

[@Geiserwoodturner]

Thanks

[@alaincaron225]

Excellent video for a beginner looking for basic to look after and avoid mistakes on lathe purchasing. Thanks

[@dancoxe5421]

Just the video I was looking for before buying a lathe. Perfect amount of detail.

[@Geiserwoodturner]

Glad it was helpful! Good luck

[@kimr5841]

I thought I knew most things about lathes, but you proved there is always more to know. Thank you for that.

[@brandonlovelife9171]

Thank you very informative

[@draynraB]

Just looking into getting a lathe so I very much appreciate your advise, wisdom and experience on this topic. Straight forward, no non-sense, and informative. Thanks !!

[@Geiserwoodturner]

Thank you! That is exactly what this video was intended for. I’m glad to hear it was helpful.

[@arasul]

By far the most informative video I have watched so far.

[@Geiserwoodturner]

Thanks I wanted it to be packed with information! Thanks for watching!

[@MikePeaceWoodturning]

Great video. Kudos for the variety of shots and B Roll.

[@Geiserwoodturner]

Thanks Mike! Great to hear! I’ve had many good ideas from your channel as well. Thank you 😁

[@dennismacwilliams196]

Very much good info. Thanks

[@JoshWrightWoodworking]

Thanks for the video dude! I'm looking into buying a lathe and I have no idea what im doing. This video was incredibly helpful.

[@Geiserwoodturner]

Glad I could help!

[@Makermook]

This is a great video for learning the basic, need-to-know parts of a lathe. Thanks!

[@Geiserwoodturner]

Thanks, I’m kind of a tool geek! 😆

[@ecko827]

im from philippines and i really like this kind of work . hope someday i can buy that kind of lathe :( i have my own but improvise . just for ballesters only . i really love doing cups bowls etc. but for now , imagination :)

[@Geiserwoodturner]

Nice! Keep going, it was many small miracles that led to my lathe! I hope things work well for you.

[@ecko827]

@@Geiserwoodturner thankyou. done clicking the subscribe :) God bless sir.

[@autumnknight8710]

Excellent presentation Sir - Thanx

[@Geiserwoodturner]

Cool thanks! Although I don’t go by “Sir”. I’m just a regular guy. 😁

[@SimonWrigley]

Thanks, wonderfully informative and loved the woodchuck!

[@Geiserwoodturner]

Thanks! I spent hours learning how to put the woodchuck photo together. Now I’ve forgotten everything! Pretty normal I guess.

[@diycharger1760]

Good video. Thanks for sharing

[@Geiserwoodturner]

Thanks so much

[@tmikeporter]

well done; I've had my Laguna like yours now for several years. Solid lathe.

[@Geiserwoodturner]

Laguna doesn’t do too bad for the price!

[@walonguy111]

Nice video, very very informative ! Thank you

[@chrisgriffith1573]

Some of the best things to know about wood turning lathes. I am looking at buying a lathe, and do not know a lot, this helped me understand what I need to look for, and how to shop for value. Thanks.

[@Geiserwoodturner]

So glad I could help!

[@crackerjack3359]

I have been turning for a few years now and need to upgrade my 14" general lathe. I love the lathe but have outgrown it and I'm testing its limits. Mainly the weight of blanks at 13.5" by 6" that I'm turning. Your video is a good reminder of the elements involved in choosing a new lathe and it was was well worth watching. Thanks.Montana Wood Art Bozeman MT.

[@Geiserwoodturner]

Thank you! It was hard to do this subject justice. As you know there is much more than I could ever include in a video. I’m always glad if this helps in your decisions! 😀

[@markdarus8540]

Great video! Highly informative. Thank you for sharing.

[@Geiserwoodturner]

Thanks much!

[@theogburner]

Very well thought out and informative. I sure wish I would have seen your video before I bought my lathe. Your video hit many more points about needs and wants. As it turns out my choice of lathe was just right for me and your video would have saved me a lot of time. Following your points led me to the lathe I have and, for what it's worth, I suggest anyone watching this video to watch it a few more times and really concentrate on the questions and points brought out. You will save yourself time and possibly heartache if you follow Jason's advice and guidance. Sorry for the long comment. Thank you, Jason.

[@Geiserwoodturner]

Thanks Scott! I’ve really been a tool junky for a long time. I love to understand why you need all these fancy features that manufacturers build in to their products. Great to hear the praise! Hope this video helps some woodturners!

[@johnr.8723]

This video is very informative and helped answer my many questions. I don’t like to ask in stores because I feel and I am just being sold to.... I watched your challenge video and found this afterwards! Great video!

[@Geiserwoodturner]

Thanks John! I often feel the same way about being sold to. I like to make my own decisions about if I think a feature will be helpful or not. Thanks so much for watching!

[@hawkeye10100]

Thanks, I sure learned a lot.

[@Geiserwoodturner]

I’m glad it was educational! Keep on learning and let it become an obsession. Just kidding..... but seriously though.

[@dylanl.4723]

I got a 1948 delta homecraft 3ft lathe with a motor and chisels for 120$. I consider myself very lucky to snag that one

[@Geiserwoodturner]

Nice! Now on to an obsession you will cherish!

[@claypigeon001]

Some great and helpful advice, thank you 😊

[@Geiserwoodturner]

I’m glad it helped! 😀

[@coleyounger4060]

Harbor Freight best buy for the money

[@drewsales]

Very informative thank you for this it's what I needed to see for helping me determine my next lathe purchase.

[@Geiserwoodturner]

Thanks for watching. I’m very glad I could help!

[@roble98]

I like the advice and/or question asking: Does it give you room to grow? I think all lathes can evenntually turn into a "growth mechanism" depending on where you want to grow to....if you want to become a pro at woodturning, you will start as a beginner and advance throughout time (hopefully saving money) until you have enough money for a bigger lathe. this will be your next one....and on and on....until you are woodturning full sized stair rails, circular tables, maybe pool tables, but that is a massive project for way later on...Mind you that's saying that you end up really liking woodtuning, if you don't or just see it as a hobby, beginner may always be a wonderful fit for you, because a beginner wood lathe and tools can make enough stuff for hobbyists that will allow you to enjoy the craft, but if you want to advance, that's gonna take more money, time, tools, etc. to succeed. The experience is nice, but it's all up to the person. So answering the 'room to grow' question....Solution to that is: It's all up to you. Plus, if you can sell your lathe work for cash to others, that always helps for further growth :)

[@Geiserwoodturner]

I like the way you put this. It makes me think of a question I heard at a professional conference once. The question was “what are you doing to improve yourself?” We should always be improving ourselves and if we are not, something is wrong and we should examine ourselves. Maybe there is something new to try or learn. Great comment!

[@roble98]

@@Geiserwoodturner Thank you, thank you :)

[@1dd434]

Thanks for your time to make a great video, learning here.

[@Geiserwoodturner]

Thanks for watching!

[@mrharlemike28]

Great video! Now I feel confident to buy a lathe. All because of the amazing detail you provided. Thank you! Subscribed for sure!😍

[@Geiserwoodturner]

Thanks. I tried to include enough information so you could make your own decision rather than just telling you what to do. I’m so glad it helped! 😁

[@nickstoic2944]

Awesome video, thank you very much. Your detailed descriptions on wood lathes are great.

[@Geiserwoodturner]

Thanks! I have read a lot of tool catalogs, and done a lot of dreaming! 🤣

[@nickstoic2944]

@@Geiserwoodturner You know, I meant my comments. Your advice on a wood lathe is full of precious information. The only video I watched that sums it all up. Thank you. I am looking forward to watch more.

[@ernielaurent671]

Dust collection is good to have when sanding.

[@jameswarner6105]

Very helpful video. Thanks for taking the time to produce one that considers so many different points without promoting a specific brand.

[@Geiserwoodturner]

Your welcome! I really tried to make it not brand specific. Besides I figured I don’t need to advertise a product unless they are paying me!

[@georgespangler1517]

I found a vintage shopsmith and installed a dc treadmill motor with speed control,,, works very well,,

[@Geiserwoodturner]

Nice! I love that kind of ingenuity 😀

[@georgespangler1517]

@@Geiserwoodturner thanks,, it has unbelievable power and very quiet and smooth,,,and I can adjust to any RPMS

[@watcherdude1330]

Very helpful ty

[@SCWD_US]

Thank you for taking the time for this. Much appreciated.

[@Caldermologist]

I live in Sweden. My regular local tool supplier only carries one brand of lathes. In two sizes. There are pleny of used cars I could get for the cost of the larger model, but I want the lathe. No point in buying a car when my woman will buy me one.

[@Geiserwoodturner]

Sounds like you have the best of two worlds! 😀

[@mikeygee4564]

Thanks for this!

[@Geiserwoodturner]

I hope it helps!

[@terrytenley9404]

I went thru this 45 years ago and made my own lathe.. My purpose was to make larger bowls.. The result was made from 3 inch maple with one inch shaft with 8 threads per inch. I put 4 pulleys top and bottom.. speeds varied from 250 to 4000 rpm. I made over 800 bowls with lather but was always to fast for out of round wood.. mostly oak firewood that was green, turned twice..10 years ago I made a new lathe from twin ibeams.. I bought a phase converter that took 220 single phase in and output triple phase.. The converter allows speeds from 1 rpm to 4000.. The result is off the charts.. This lathe takes up to 38 inches in diameter and is a brut.. The lathe weighs in at 450 pounds.. it’s has split second casters to allow movement.. that pick up and drop easlie..I have 2 4 bolt flange pillow blocks on each end and the sky is the limit.. Cost was $660.. I never worry about out of rounds anymore.. The lathe weighs so much it can’t shake anymore…. I just keep turning.. My wish is folks think about this.. a buddy that welds completed all the welds in’ 4 hours.. The inverter box cost $180 with 2 .5 hp. Motor.. This thing is amazing..think all.. save your money.. I have pictures of it on fb..enjoy your hobby at lower costs.. 😁😊👍. over 50 years I have turned over 1100 bowls that have been given away to old friends, retired good bye and sweet old ladies that needed a lift.. my way to make society happy..

[@Geiserwoodturner]

I have a buddy that built his own lathe. He is a machinist by trade and can pretty much do anything he sets his mind to. If you have the means and the know how, go ahead and build. Thanks for sharing about your lathe. 😀

[@terrytenley9327]

@@Geiserwoodturner wish I could share pictures.. I am not a machinist. my lathe is simple, very useful and cheap but built to take abuse..

[@tootall5559]

If you have some room, but not a lot for any one machine, you might consider a Shopsmith mark 5 or 6 or 7. It's many tools in one, including a lathe, and you can get extras like a bandsaw attachment. They are not cheap, especially new, but when you consider all you get in one machine, the price becomes reasonable. If you have the space for dedicated machines, no you probably don't want one, but for us guys with small workspaces, they make more things possible than say just a lathe (they're also a table saw, and a drill press and horizontal boring machine, and a few other things depending on what attachments you have.) Used they can be down right reasonable for what you actually get.

[@Geiserwoodturner]

I started turning on a shopsmith so they have a place in my heart. At this point they are a little limited as far as the lathe goes but a great machine for small spaces.

[@tootall5559]

@@Geiserwoodturner well I've never seen a mulittool of any kind that is the best at anything, but if you don't have much space, they're brilliant.

[@williamn01]

After watching your video I've decided I'm going to buy the Record herald , was going to buy a smaller lathe for £150 for starting off but think I will just go with the larger herald think all in with chuck etc will be about £1000 , hopefully get a black friday deal tomorrow. 😀

[@Geiserwoodturner]

Nice! Good luck with finding a deal!

[@robertwelsh49]

This had a ton of useful information. I'm building my shop without sparing expense, so the detailed explanation about options, and what makes the extras worth the higher cost was very helpful. Great video, keep em coming.!

[@Geiserwoodturner]

Thanks I’m glad to know this was helpful! More videos on the way soon!

[@kaizendesignllc]

The trick is in the little details. Thank you for an excellent breakdown! God Bless. I do wood cnc and hand engraving. And Tansu boxes from start to finish. If you need help or advice, let me know. Happy to pay forward! Thanks again.

[@ernestthebo5441]

Thanks! Great video.

[@hswing11]

What lathe should i buy WELL I AM WAITING

[@Geiserwoodturner]

Ha ha. I’m going to have to tell you a Robust American beauty then. 🤣

[@nickbild3538]

I’d love to own that Laguna!

[@Geiserwoodturner]

It’s a good lathe! I recommend one!

[@markswaggerty4958]

Mini jet step up pulley. Good enough for most projects

[@Geiserwoodturner]

I can’t deny Jet makes a good lathe! Thanks for the comment. 🙂

[@johnd5122]

This is the best lathe buying video - I have seen! Do you have a pie in the sky best full size lathe you would recommend with all features excluding limitations of cost ….what is considered the best out there ?

[@Geiserwoodturner]

Good question! I am torn between the Robust American Beauty or the Vicmarc VL300. Neither of which I can afford. I have demonstrated on an American beauty and it is a well thought out machine.

[@johnfritz3792]

Bought a powermatic lathe in February, still waiting for the bed extension. Now they are saying July

[@Geiserwoodturner]

Oh man hope you get it soon and can turn longer stuff soon.

[@imxploring]

Excellent video! Great job condensing a lot of information into a very informative video! Thanks for posting!

[@guloguloguy]

AWESOME ADVICE!!!! THANKS!!!

[@Geiserwoodturner]

Glad you liked it! I’m open to suggestions for other videos on what you think would be helpful.

[@Tolugba]

This is far away most helpful video I've seen on the subject. Thanks very much

[@Geiserwoodturner]

Thanks! I worked the hardest on this video more than any other because I wanted to pass on the knowledge.

[@Tolugba]

Brother, you did it. thanks again. Another question for you if you don't mind. Where do you find logs, wood for turning? I live in the northeast.

[@Geiserwoodturner]

Good question that needs a really long answer. Maybe I’ll do a vid on the subject sometime. Short answer is lots of different places. Neighbors, hardwood suppliers, online, yard waste disposal piles. That’s just a few sources. Just keep turning! once people know you turn, wood will just start showing up!

[@Tolugba]

Fair enough. I believe that. Thank you

[@richardhawkins2647]

I'm stuck in indecision! I have a budget 1216 midi lathe with EVS. I tried turning a 12" bowl on it, I managed to get it done but felt very sorry for the lathe and promised I wouldn't do that to it again! Apart from that it has been a great lathe. My first thought was to get one of those generic Reeves drive long bed lathes, just for turning bigger projects. And keep my midi lathe for smaller projects. That's about all my budget would allow at the moment. Also, I'd have to get rid of some stuff to make room for it. Most advice seems to be don't buy budget gear. Also, as much as I like my midi lathe, upgrading to a decent solid built machine is appealing, except for the budget! Conundrum, do I get the 2nd budget lathe to compensate for what mine can't do, and use that until I can afford a decent lathe. Or do I just wait until I can afford a decent machine. And how long will that take?

[@Geiserwoodturner]

Thanks watching! I think this is a conundrum for most of us. Do I get only what I need or do I get by and save for what I want? I’ve been there many times and there is no easy answer. The best advice I can give is keep your eye out for the best possible deal for your budget. There are many alternative ways to find a good lathe if you look hard enough even on a budget. For instance schools often have equipment they are getting rid of for auction. A good machine is definitely worth the wait. I honestly believe if we intend on growing our woodturning abilities and we concentrate on what will best help us do that, the right lathe will find it’s way to us. If you are considering the Reeves drive, I know a guy that owns one. He’s rebuilt the Reeves drive twice now and still loves the lathe. I wish you the best!

[@richardhawkins2647]

@@Geiserwoodturner Thank you, that's really helpful. I will focus on getting the lathe I want rather than compromise and get one that will fill in. I appreciate the suggestion of getting a used machine, but my little local turning shop stocks the lathe I want, and I tend to want to support them as much as I can. It's pretty much a mom and pop store who make you a coffee when you go there! I always spend too much there! Thanks again. In addition, I saw a review of the budget lathe I was thinking of getting and the biggest complaint was poor build quality, so that also helped!

[@hemphunterschefarms208]

great video new wood turner myself so thanks and cant wait to watch your turning videos and i myself will be uploading some turning stuff on my channel

[@Geiserwoodturner]

Thanks for watching! I’m a big fan of woodturning vids on KZbin so let me know when you upload I’ll go check it out!

[@tangobravowhiskey7771]

Do you have a video showing the advantages/ disadvantages of a sliding headstock vs. a swivel headstock?

[@Geiserwoodturner]

I don’t have a video at this time on this subject. Interesting topic though. I’ve only ever used lathes with a sliding headstock. Both would make it possible to get the lathe bed out of the way for outboard turning. The only differences would be in the comfort of the user and price of attachments needed to outboard turn. There are some advantages to either one might make a great video! Thanks

[@fidelmenendez3495]

THANKS FOR THE EXPLANATION

[@golemtabak1183]

Just great! Thank you very much!

[@watermain48]

Great video, loaded with a lot of good information, but those of us wearing hearing aids wish you wouldn't use the irritating background sounds.

[@Geiserwoodturner]

Thanks for watching! Even though the irritating sounds. I’m working on it thanks! ☺️

[@lynbren]

Well done review, very informative

[@hussainal-hussaini8483]

Very informative video.. Thx a lot 👍🏼

[@Geiserwoodturner]

Thanks so much for watching! I hope it helped.

[@lendernunez9094]

Hey Jason, I am Lender and I’d like to start my own business here in the Cayman Islands and I’d like to start turning these wooden things to put flowers and also small bowls to use like sugar for the coffee and stuff, basically like to specify in a few things for decoration and also to give it some of use, so, what do you think it will be like a list to start…?????!!!

[@Geiserwoodturner]

Hey Lender, this question has more answers than I can give in a short comment. For now the main thing you need is experience. Learn all you can and try it out! A basic list would include a wood lathe, turning tools, a chuck, drill bits, and the list goes on from there. You can go high tech or low tech (people have been woodturning for thousands of years). Find something you want to make and figure out what you need to make that project. Try to find experienced woodturners that can help you along the way. Hope that helps! Welcome!

[@paultay23]

Thanks cool advice, i have just purchased (not got yet) a mid sized lathe Record DML320 (i am in the UK) I have just ordered a Record Power SC3 Geared Scroll Chuck Package. Your video has convinced me i have done right. I now need to educate myself before leaping into a buying a starter pen turning kit. Cheers Paul

[@Geiserwoodturner]

This is great! I’m so glad this video helped. I tried to keep it generic enough that it would help wherever you are. Besides there aren’t any lathe manufacturers filling my pockets with money so......🙂 Enjoy the woodturning!

[@foxmoulder7724]

Woah this is a little overwhelming. Id love to get into woodturning logs and stumps, but i guess id better slow down and look at what i need. Ty

[@Geiserwoodturner]

You will be happier with the results the more tackle woodturning one step at a time. Sounds like you are on the right track. Thanks for watching! I hope you are turning those logs and stumps soon.

[@waltgranger7951]

Great video, want to start wood working, I would like to only buy a lathe once and would like to do big things, have a nice budget what would u recommend lathe, tools ect. Thank you

[@Geiserwoodturner]

If you only want to buy once and large capacity is what you want. I would look into Robust, Vicmarc, or even Oneway or Powermatic lathes. I listed them in order of my preference but all are good trusted brands. If you go with a Powermatic on Amazon click on one of my links before you do. 😉😆😁 it won’t cost you anything and I’ll make a small commission. But seriously they make a 24” capacity lathe with a sliding headstock for outboard turning if you want to go larger. I’m really in love with the Robust American Beauty as well check it out. I wish you well!

[@chellegriggs]

It was very informative...but I'm still so confused. Money and space are not a issue but I will be a wet behind the war beginner...show I start with a midi...

[@Geiserwoodturner]

If money and space aren’t an issue it doesn’t hurt to start with a midi lathe. If you want to you can always upgrade when you want to do bigger items. Especially if you have the money to upgrade. Thanks!

[@bouyant8659]

straight up.. thanks

[@woodworkingmachine3296]

nice

[@adamp3663]

Very informative, thank you. I do have a question. How long does it take the average person to become proficient at using a lathe? I’ve started my wood shop a little over a year ago and I understand you never stop learning. I’m just curious as to how long it would take someone to become confident and capable.

[@Geiserwoodturner]

It depends on the person, but I would say it can take several weeks to several months to become reasonably proficient. It depends on how often you practice. Also, it is really helpful to have a more experienced mentor in your area to bounce ideas off of. “Confident and capable” takes more time and is added on to you with each successful piece you are able to complete. It means you also have a lot of failures and you’ve learned how to correct them. Really I’d say after a year if you have the practice and learning in, woodturning really begins to be less of a worry about doing something wrong, and more relaxing and enjoyable! Best wishes!

[@pbaranda]

I am a smoking pipe mater what lathe would you recomend. Price is not an issue, thank you for the great video.

[@Geiserwoodturner]

Here are some brands I’d recommend. After that you have to determine the size and features you need. I’ve never made pipes yet so I can’t tell you. If price is no issue I’d go with Robust, Oneway, or Powermatic. Otherwise jet, Nova, and Laguna make great lathes. I hope this helps.

[@pbaranda]

Hi, Thank you very much for the quick reply and information. I have been researching the Laguna Series of Lathes and they look very good and have as well pretty good reviews everywhere.

[@mkivy]

Thank you so very much. I am going to take a class and hope to buy my first lathe after the class or during the class. I am so addicted to watching turners on You-Tube. I know I am no caliber close to most of these men and women, but I should be good enough to turn a bowl? Should I wear gloves? I’ve also seen some wear Respirators?

[@Geiserwoodturner]

Congrats on getting training and a lathe. You’ll have a lot of fun with it! There’s a debate about wearing gloves. Some say they could get wrapped up in the machine which is possible. I rarely wear one. Sometimes I use a glove on one hand when roughing a large bowl that throwing slivers and chunks. I don’t touch the wood with a glove and take it off when I don’t need it anymore. Also any method is good to try to keep wood dust out of your lungs. I use a dust mask and a fan to move the dust away from me. Hope that helps. 😀