Genisys Reset

[@josephhaney884]

Thanks so much - tan out of oil, the first two restart attempts failed - followed your instructions - problem solved . Thank you

[@danlivni2097]

Thanks for showing where the reset button is

[@sophiefergifan7153]

everything was woking great, outta no where pump prime have a yellow light and it won't start

[@Yvng_LifeIV]

I have no light and I’m holding for 15 seconds but nothings happening, what should I do

[@silversonic99]

You figure it out?

[@BrianVogel-ej4vl]

No light but blower on

[@AngolmorAtsuma]

Great video I was no where near patient enough to hold the reset button for 15 seconds!

[@508_Phax]

SAME EXACT problem i was having lmao..!

[@annielee2897]

Same here lol

[@bikewhorder]

I've held the reset light for 15 seconds. IT WILL NOT GO OUT! I've held it for a minute i've held it for two minutes. Nothing I do will make it go out. Please help it's freezing in here.

[@tommytom4796]

Should there be any lights lit up when the oil burner is not running on a Beckett Genisys 7505 ? when my furnace comes on the only light that comes on and remains steady on is the green flame light ...but when the furnace turns off that turns off and no lights are lit but yet I could have sworn that the big window where the reset button is use to always be lit in red but am not sure...should there be no lights on when the furnace is off and when it comes on only the FLAME light comes on like mine is doing ? Thank you.

[@508_Phax]

FUCKN GREAT HUUGGGEEE THANK YOU MY DOOD....let there be hot water !!! "Hard lock" problem solved

[@killswitch7775]

I was locked out; had to hold it for 15 seconds

[@stumpynubs5387]

When replacing the 7505 is it plug and play or do you have to program it?

[@TheStickySituationsShow]

Big savior right here

[@annielee2897]

Thank you for the very use full info.

[@michaelo691]

What if my three lights turn on for a second then everything shuts down?

[@Anna-lc4no]

My genisys buckett is not lit should it be lit anywhere on the box? The oil boiler goes on and it wants to start but then it doesn't it sounds like the pilot is not on, how do I fix this?

[@alexmetz3493]

I have a AF in my shop on radiant tube. The post purge is set at 4min but it only goes for 15 sec. Doesn’t matter what time I set it with the programmer it stays at 15sec. Can it be reset or is controller faulty?

[@christopheryanoski6899]

The guy that installed mine left it just dangle. Lol. I just ran out of and got oil and now it won't even let me reset it. The damn thing just keeps blinking. Looks like I gotta call a plumber.

[@falsehopehero]

Why is your thermostat jumped together? That's the only way mine will run is to jump those front contacts together :/ but that's not good right?

[@lesliegreer3022]

Thank you!

[@bambiplantz202]

But what if nuthing lights up no lights at all and the furnace keeps turning off and on over and over

[@edwincorreajr]

Thank you

[@drewcillastone5200]

Thank you! This helped perfectly!

[@09fatbobmike]

what about if you have no light on but the furnace will not kick on.

[@MrHeatingairman]

Hello Ratpack, That could be a number of different issues. Possibly no power to the furnace.?. Good place to start. Sorry for the late reply.

[@MrHeatingairman]

No, the burner fan will not run while resetting.

[@jmv110]

after the reset, my system will lock out again after 30-40 minutes of heating

[@fishsquishguy1833]

Johnathan Vinson What did it end u being?

[@jmv110]

The line from the tank had a pinch in it

[@fishsquishguy1833]

@@jmv110 Cool thanks for answering!

[@brianvogel-qp7gu]

No lights at all on control box

[@romeyo401]

I tried resetting it but it shuts off after a little while and the oil still not bleeding

[@michaelo691]

Did you find a solution to this problem?

[@wiseblissnp]

Should the unit fan run while resetting?

[@AngolmorAtsuma]

The fan should be set to auto if possible.

[@INTERGRATEDMA]

Thank you... this video saved me...

[@brianvogel-qp7gu]

No red light on box

[@melissabergman8585]

thank you! video helped me

[@WayneHeslerMondore]

why are the two terminals jumpered, mine connect to the thermostat

[@MrHeatingairman]

This application uses a high voltage thermostat in series with the burner control. Low voltage connections usually go to these terminals.

[@robertbobinis3076]

I texted a reset now I don't have anything

[@stumpynubs5387]

When replacing the 7505 is it plug and play or do you have to program it?

[@Scrounge4]

Thank you!

[@MrJoseplaylist]

Thank You!