I have the 115 nibbi jettings and a 115 unbranded jets you can get from motorcycle shops. They are different sizes the 115 nibbi jets are smaller despite the same number size. But when I check the 122-125 nibbi jettings, it turned out to be the same with the 115 unbranded jettings
@trident88723 жыл бұрын
I have installed k&n airfilter for my Apache RTR 160 2012 model but airflow is increased and fuel supply is not proper so which jet should I change main jet or pilot jet or both?? Also tell me the diameter which will change proper fuel mixture with k&n airfilter,I also installed NGK iridium spark plug.
@EzMeck3 жыл бұрын
Start by increasing the main jet alone. One size at a time. The best main jet for your setup will give you best top speed. This is how you can check. I dont think pilot jet needs replacement. Adjust the pilot screw, and you will be fine.
@trident88723 жыл бұрын
@@EzMeck also tell me if I use racing cdi so rpm gets unrestricted and you get higher RPM does that really gives top speed??
@purwajtiwari65923 жыл бұрын
Hi Rajib, thanks for the informative video. I followed these instructions and drilled a 1.2 mm hole in the main jet of my Fz16 - 2012 installed with K&N RC 1060 filter, SC project exhaust and Nikavi Iridium spark plug. The throttle note sounds crisp and there is no problem with the idling. However, when I'm at WOT, it revvs till 75 kmph (or ~5000 RPM) smoothly but then starts pulliing back to around 68-69 and feels like it's losing power and dying out. Also, when I lower the throttle to 80-90% the bike again accelerates to around 85. I'm not sure if the mixture is too rich or too lean since these are the problems faced with lean mixture but on the other hand I've increased the size of jet. It'll be really helpful if you could share your ideas on it.
@EzMeck3 жыл бұрын
Keep the bike on WOT, run for sometime on wot. Now at wot turn the engine off by engine kill and pull clutch and use brakes to stop the bike. Now check the condition of spark plug tip. I think its a symptom of richer mixture. But can't confirm without riding it.
@SHADOW_SPECTRE4 жыл бұрын
Sir I have to install free flow or k&n filter in my bike do I have to rejet or just to tune my carburetor Plz can you reply fast its urgent
@EzMeck4 жыл бұрын
Rejetting is must, try increasing the main jet 2.5 size at a time. Use a inline catalytic converter and a db killer to maintain the back pressure, otherwise the bike wont pickup
@SHADOW_SPECTRE4 жыл бұрын
@@EzMeck thank you
@jayeshmeriya71532 күн бұрын
How to get perfect drill bit for perticular jet size plzz roly
@tridip.chakraborty4 жыл бұрын
Getting addicted to ur videos 😍
@EzMeck4 жыл бұрын
😂 haha
@sriramkumar95773 жыл бұрын
Dear friend, you are doing a great job. BUT, I HAVE A PROBLEM WITH THE PILOT JET OF MY RX100. I LOST THE PILOT JET, WHILE CLEANING THE CARBURETTOR. NOW, BIKE IS NOT STARTING. HAVE YOU ANY IDEA TO GET A NEW PILOT JET? I PURCHASED FEW CARB KITS, BUT THEIR PILOT JET SIZE IS TOO BIG, AND ENGINE IS NOT STARTING. HOW TO MAKE A PILOT JET FOR MY RX100.
@EzMeck3 жыл бұрын
Search it on safexbikes.com
@sriramkumar95773 жыл бұрын
@@EzMeck ok thanks, I will try.
@ravikilaji87372 ай бұрын
Sir meri drem yuga bike me konse namber ka jet lagau kiteni baar jet ka namber chenj kiya par nai aata hai please help me
@jayeshmeriya71537 ай бұрын
And can i do the same process for slow jet !?
@jayeshmeriya71537 ай бұрын
I'm little bit confused, with how can I decide a drill bit to make perfect hole
@Thevintagegaming3 жыл бұрын
Bhai mere honda cb trigger main jhatke leti hay low speed 30 to 35 main kya karu 😭 jese petrol khatam ho gaya ho 😭😭 help me bro..
@EzMeck3 жыл бұрын
Carburettor clean karwao, savi jets ko wire se clean karo, or diaphragm rubber check karo.
@Thevintagegaming3 жыл бұрын
Clean karwaya 2 bar lekin mechanic bolta hay jet pin Thora bara karna hoga, kya ise mileage main effect parega..
@EzMeck3 жыл бұрын
Ha, isse mileage ghat jayega
@kjois6198Ай бұрын
What's the use of this for bike ?
@dedeabsrn80444 жыл бұрын
Automatic choke does not activate in cold engine. What is the reason? How do I set it.?
@EzMeck4 жыл бұрын
Might be a bad choke circuit. Try replacing the choke assy
@vrcvlogger3 жыл бұрын
अच्छी वीडियो बनाते है आप 👍
@InsaneGear2 жыл бұрын
Sir meri szx bike hhsi hai wo start hone mei problem kar rahi hai aur missing bhi kar rhi hai aur uska carburettor bhi overflow kar rha hai
@EzMeck2 жыл бұрын
Zada petrol ja raha hai, carburettor ki problem ki wajah se hi ye problems aa raha hai, repair or replace it.
@InsaneGear2 жыл бұрын
@@EzMeck sir how can I repair it
@InsaneGear2 жыл бұрын
@@EzMeck please help me sir I am student I don't have enough funds to replace
@EzMeck2 жыл бұрын
Following the video try to stop overflowing problem, that will solve the issue hopefully. kzbin.info/www/bejne/bnyzqmWnhpanqbM
@APPAISLIVE444 жыл бұрын
Hii bro mere Pas NS200 HE NS Ka jet 115mm Ka he ye iski madat he me 117....ya 118 Baba sakta Hu kya????? Plz reply
@EzMeck4 жыл бұрын
Itna kam jet size increase ye bits se nehi hoga, isse 10 size karke increase hoti hai, Agar 2/4 size increase karna hai to reamer use karna hoga, www.google.com/search?q=carb+jet+reamer&client=ms-android-xiaomi&prmd=sivn&sxsrf=ALeKk01YXnqxwxaIkziJQSXPN6j9AFhLXg:1600784884482&source=lnms&tbm=isch&sa=X&ved=2ahUKEwjvxZqz_PzrAhXgyzgGHSSlD28Q_AUoAnoECA0QAg&biw=360&bih=560#imgrc=Vg4Vkc9GzsdDHM
@APPAISLIVE444 жыл бұрын
@@EzMeck bro can I get 118 mm jet from safexbike site????
@EzMeck4 жыл бұрын
I don't think so, get 117.5 from Bajaj spares shop, pulsar 150 ug4.5 main jet.
@APPAISLIVE444 жыл бұрын
@@EzMeck ok bro thanks
@kumarabandara1415Ай бұрын
Ct100 main jet size please
@dualstand140610 ай бұрын
Hii Rajib, Mera pass classic 350 bs3 2014 model hai. Iss me maine performance air filter and megaphone exhaust install kiye hai. To mujhe carburator ki kaun kaun jets ko kitna size mein drill Karu? Please help me bro
@EzMeck10 ай бұрын
Check the main jet size, just go one size up at a time. It's recommended to get a spare stock mainjet in case the experiment goes wrong. There is no drill size to mainjet size chart. Just need to find out as I did, which drill fits just right and use one size up drill to get one size up jet. All the best!
@dualstand140610 ай бұрын
@@EzMeck oooh..wao. Thank you so much
@dualstand140610 ай бұрын
@@EzMeck so only the main jet is to require one size up or both the jets?
@jaggasingh9303 жыл бұрын
Sir cd 100 honda me main jet kon se number ka hota
@sukumarpradhan6034 жыл бұрын
Weldone
@RadhakishanJaat-z2c Жыл бұрын
This man he is a boss
@EzMeck Жыл бұрын
Haha.
@uniquerider6943 жыл бұрын
#Bhai mene ct100 me free flow wala exhaust install kiya hun Pickup kam he acceleration aur jab high pe hota he to missing karta he jaise petrol khatam gaya aisa lagta he problem kya he .?"
@EzMeck3 жыл бұрын
Petrol kam ja rahi hai, carburetor tune karo. Main jet bigger size dalo
@uniquerider6943 жыл бұрын
@@EzMeck thanks but mere pass uska hi old carburetor he to wo old carburetor ka jet me bada size ka drill karke new carburetor me install karke aur tune karne se improve hoga kya pickup bhi badhega na ?
@EzMeck3 жыл бұрын
Drill konsi size me kar rahe ho isse bohot farak par sakta hai, jets ki diameters bohoti chota hota hai, so soch samajh k bits use karna.
@uniquerider6943 жыл бұрын
@@EzMeck please aap bata do aise koi idea nahi he keivin aisa naam ka carburetor laga he usme
@EzMeck3 жыл бұрын
Safexbikes.com website se spare main jets kharidlo keihin k, fir uspe drill karke experiment karo, ye video me jo drill bits use kiya hai maine wahi bits use karna.
@jayupadhyay6262 Жыл бұрын
Yamaha ki konsi bike ka jet h ye
@sekhorjitnaorem58333 жыл бұрын
Bro. Kaya fascino carburettor main jet fit hoga ya nahi
@EzMeck3 жыл бұрын
Yes, fit hoga
@sajidkhan-ow9mc2 жыл бұрын
Carburetor ke jet size chota karke ya mealage ko badha sakhte hai
@EzMeck2 жыл бұрын
Thora increase hota hai.
@sajidkhan-ow9mc2 жыл бұрын
Mere pass honda shine hai isme kitne no ka jet lagta hai mealage bhada ne ke liye
@sureshprajapat5102 жыл бұрын
Sir star city 110me jet kitne no aayega
@yamaharx100upgrade43 жыл бұрын
Can you please give in one main jet for my yamaha rx hundred.
@EzMeck3 жыл бұрын
They are readily available in safexbikes.com
@kumarabandara1415Ай бұрын
කරුණාකර Ct 100 ප්රධාන ජෙට් ප්රමාණය
@virendraSingh-my4fc2 жыл бұрын
Bhai i have 1978 bullet jiska average kafi kam h agar 90 ki jagas 80 ka jet laga le to is koi average me effect hoga
@EzMeck2 жыл бұрын
Try karke dekh sakte ho, lekin mujhe nehi lagta ki 78 ki bullet se zada mileage mil sakta hai. Kyuki ye bikes bilkul v efficient nehi hai, petrol loss bohot hota hai, iske liye hi mileage itna kam deti hai.
@shadankhanmk193 жыл бұрын
###🤔aacha ye batao Splendar carborator pickup 6.7 saal key baad q kam ho jata hai 🙄🙄🙄
@EzMeck3 жыл бұрын
Age hone k sath pick up thora down hota hai, carburettor ki parts valves piston savi pehle jaisa efficient nehi rehta hai.
@shadankhanmk193 жыл бұрын
Aagar ham jed kit chenz KR dein to carborator pickup Bad sakta h Kiya
@EzMeck3 жыл бұрын
Usse zada farak nehi padne wala.
@shadankhanmk193 жыл бұрын
Aaccha to fir Kiya krna chahiye carborator pickup badane ko men jatt ka holl badane se pick nikal sakta h 😳😳
@rafiqueahmed66152 жыл бұрын
Ye box Kitne ka he or kahanse milega
@EzMeck2 жыл бұрын
Check links in the description
@syedmoin97682 жыл бұрын
I need jets 115 and 12.5
@pittamohan7834 жыл бұрын
Hi friends does any know main jet number of Tvs Suzuki Shogun
@hummingbird9574 Жыл бұрын
100
@karthikgowda95893 жыл бұрын
Where can I buy this tool drive
@EzMeck3 жыл бұрын
I bought it from amazon, check in the description
@jyothismgeorge60134 жыл бұрын
😍😍👌
@kuldeeps.official2 жыл бұрын
Hiii sir Maine rajdoot ka new carburettor liya hu par e pick-up nhi de ha
@supritipradhan24694 жыл бұрын
👍👍👍👍👍👍
@bikeclub773 жыл бұрын
👍👍👍👍
@MdIbrahim-lv9jp2 жыл бұрын
Maijet kaha pane
@mohangarageandelectronicse28003 жыл бұрын
Carburetor are best then Fi
@EzMeck3 жыл бұрын
Agree, its simple more reliable easy to maintain, easy to repair, cost less. Just a little less efficient than fi.