Рет қаралды 7,250
Подписывайтесь на мой инстаграм - anna.kovaaleva?igshid=YmMyMTA2M2Y=
В работе использовала секундный клей - ad.admitad.com/g/8v5m18bho3bc07278128940fe8e826/?ulp=https%3A%2F%2Fwww.obi.ru%2Fklei%2Fklei-sekundnyi-moment-super-gel-3-g%2Fp%2F1056589
В данном мастер-классе я делюсь с Вами опытом и впечатлением по работе с гигантским молдом. Данный молд у меня размером 28*23см. Изготовлен из пластика.
В своей работе, для листвы, я использую иранский фоамиран 1мм., так же допустимо использовать фоамиран толщиной 2мм. Если мы изготавливаем листву без молда, тогда необходимо вырезать квадрат необходимого размера, в зависимости от того какого размера хотите получить листву. После сделать по периметру листочка надрезы. Нагреть утюг. Слегка по краю лепестка провести по утюгу, надрезы будут отходить друг от друга.
Если мы используем в работе молд, тогда необходимо вырезать лепесток по молду, взять плед. На одну сторону пледа положить молд, на него лепесток фоамирана, затем простынку. Хорошо прогреть по простыне утюгом. После накрыть пледом и опираясь на руки всем своим весом, продавливать прожилки. После, приклеить проволоку к листве. Проволоку лучше использовать в диаметром от 1,5мм. до 1,8мм. В данном случаем у меня проволока диаметром 2мм., и работать с ней сложно, так как очень жесткая. Отрезала необходимую часть проволоки, обмотала тейп-лентой.
В видео я тестирую два вида клея. Это терпопистолет и секундный клей. Секундный клей намного быстрее и прочнее склеивает чем горячий. Ссылка на клей-гель указана в начале видео. Главная техника приклеивания проволоки в листву, это то, чтобы клей не вытек наружу и его не было видно. Для этого необходимо сжимать листву между собой по направлению вниз, к проволоке. Спасибо за внимание, если понравилось видео ставьте лайки, пишите комментарии.
________________________________________________
In this master class, I share with you the experience and impression of working with a giant moldom. This mold I have a size of 28 * 23cm. Made of plastic.
In my work, for foliage, I use Iranian Foamiran 1mm. It is also permissible to use Foamiran 2mm thick. If we make foliage without mold, then it is necessary to cut a square of the required size, depending on what size you want to get foliage. After making around the perimeter of the leaflet incisions. Heat the iron. Slightly on the edge of the petal to hold the iron, the cuts will move away from each other.
If we use molds in work, then it is necessary to cut a petal across the mold, take a blanket. Put a mold on one side of the blanket, a foamiran petal on it, then a sheet. Warm up the sheet well with an iron. After covering the rug and leaning on your hands with all your weight, push through the veins. After, glue the wire to the foliage. The wire is best used in a diameter of 1.5 mm. up to 1,8mm. In this case, I have a wire with a diameter of 2mm., And it is difficult to work with it, since it is very hard. I cut off the necessary part of the wire, wrapped it with tape.
In the video, I test two types of glue. This tvertopistolet and second glue. Second glue is much faster and more durable than hot glue. Link to glue-gel is listed at the beginning of the video. The main technique of sticking wire into the foliage is that the glue does not flow out and is not visible. To do this, it is necessary to compress the foliage between them in a downward direction to the wire. Thank you for your attention, if you liked the video, put likes, write comments.
Subscribe to my instagram - anna.kovaaleva?igshid=YmMyMTA2M2Y=