Eagle eye LED fog lights installation

2009-2013 Mazda 6.
Due to problems caused by other users that are claiming to be the owners of the songs that I create, I decided to not use music on my videos from now on. Please enjoy the technical part of my videos!

[@stateboy80892]

Nicely done... I'm considering this option!

[@22artm]

Nice job!!

[@suattinaz3705]

wonderful operation

[@themikeymikechannel2947]

I did 3 on one side and 3 on the other side of the rear bumper as reverse lights but with little led lights on my old car back in 1997 , cardomain.com/96 saturn sc2 , keep looking you'll find it.

[@tylerkimdura6690]

Hey man these get up to like 100 degrees within minute, does this happen to you?

[@Masomanable]

hey i have existing fog light wiring and switch but the lights were broken ina accident, can i install these LEDs to my foglight cover, then tap the wires directly to the existing fog light wires would they work with my switch in my car for turning them on and off?

[@gigi19mai1]

+Mason Sesak sure! The leds are 12v !

[@chrisjameshandson]

Can you take a photo or video of the installed drl/fog light you installed from the driver pov! I want to see the spread or the throw of light. I liked you idea, i'm planning to do the same on Civic. I really want to know how bright they are before i drill these onto the front fog grille!

[@gigi19mai1]

Check one of my other videos " LED headlights conversion", at minute 8:00. Before the low beam, the eagle eyes turn on first.

[@raymondkhan2709]

Did you ever do it to your civic. If so can you upload a few pictures or video. I'm about to do it to my civic and curious of the throw as well

[@Danny-kl4ow]

Hey could you explain to me the part where you connect it to the original fog light wire and how do you connect the passenger side too please?

[@gigi19mai1]

In this case, because there were no pre-existing halogens lights, the only connection is to the side lights. What you see me doing is just basically reattaching the factory halogen wires to the dummy plug. That how most of the cars comes from factory prewired for everything, just the final product is missing depending on the car options (speakers, stereos, switches, actuators, halogens).

[@orlandofernandez8499]

So is that a turn signal ? So it blinks at the same time ? ?

[@Bk1_sk]

I have a 08 mazda 6 been looking to add fogs as a diy but i took out the bumber and it only has a connecter on the left not right do i have to wire the one on the right to left one.

[@gigi19mai1]

If you are using the factory connector then you also need to replace the combination switch that turns the light on. In my case I tapped into existing side lights wiring.

[@Bk1_sk]

Emil Carlover i have no problem getting the combination switch its the right side harness i am missing

[@gigi19mai1]

@@Bk1_sk mine was the same. The factory fog lights might have a wire running in between the fixtures. So yes, you need to run a wire from left to right.

[@alexcelbun]

What kind of leds are these? I would like to put on my car the same leds but don't know which ones yo choose. What shall I pay attention to when shopping for this kind of leds and what's the most common place to order them (sites)?

[@gigi19mai1]

+alexandru calancea I buy mines from ebay for $1 each. They are called eagle eye led latest version (smaller size). On my car I have them for over 3 years. Very easy to change if one fails, just cut the wire and replace the led.

[@alexcelbun]

Thank you. How many went bad during the 3 years?

[@gigi19mai1]

got them installed on 2 cars, 10 leds each car (20 in total), 2 leds replaced so far! Not bad at all for the price!

[@cedanecox5733]

helpful video but do you know how to install "led daytime running lights on the mazda 6 atenza 2011?

[@gigi19mai1]

Stand by! That's my next video! Takes like 3 weeks to get the parts.

[@gigi19mai1]

Hi! To install any led bulbs to the exisiting high beam wiring won't work. I've tested the wires and the voltage that comes out throught the high beam wires during the daylight is under 1V, and the eagle eye led which is a 12v can only operate down to 7v. Hopping to do it this way because I have the auto lights switch and didn't want a separate circuit, but won't work. So, for the DRL you will need to run a separate circuit powered by battery and with a separate switch.

[@grandparolie]

Emil Carlover couldn’t he have just ran the hot wires to the hood fuse box but use a inline fuse so when you turn on your car they will get 12 volts and just find a good ground??

[@FatherOfAllGuys]

Are they actually functional or just for looks. They seemed too weak to me.

[@gigi19mai1]

+Abu Ashshabab they do an excellent job! They illuminate up to 5 m and sides too, completing the weaknesses of the low beam (right in front of the car)

[@nenocoelho1571]

where can I buy this kit?

[@gigi19mai1]

Ebay

[@Delrondae]

I’m still so confused. I’m trying to put these lights in my bumper above my fog lights. How do I wire them then ? Please help

[@gigi19mai1]

Check 5:24! Connect to the wires from the side amber lights.

[@Delrondae]

@@gigi19mai1 will my amber lights still works if I connect the new lights to that wire

[@Delrondae]

Trying to do this for a Ford Fusion by the way

[@gigi19mai1]

@@Delrondae Yes

[@Delrondae]

@@gigi19mai1 okay. Last question. I am trying to wrap the led light wiring around the fog light wiring. When I have 3 of the led lights on the wire the fog light and the led lights come on. But when I wrapped all 5 around the fog light wire then only the led lights came on instead of the fog lights. They were all taped and secured very well. Do you know why the fog light may not be working ? Also in this process some pieces of copper did come off the fog light wire but doesnt make sense if the led lights work

[@raymondkhan2709]

Great tutorial. How long have these lasted

[@gigi19mai1]

I still have them on my sister's car (the red Mazda from the video). Few burned out, but I purchased multiple for replacement throughout the years

[@raymondkhan2709]

@@gigi19mai1 thank you

[@rglautovlog7967]

@@raymondkhan2709 wow almost 7 years

[@mabast007]

Why you are not talking...

[@gigi19mai1]

Because I was planning to add a song!

[@gwapongakolang1903]

😹😹