Cho mình hỏi cách setup như BC2 trong ví dụ thì khác gì so với việc mình apply pressure load trên mặt đó? Cảm ơn bạn
@vandangtran64544 жыл бұрын
không có j khác cả bạn. Nhưng theo kinh nghiệm thì dùng điều kiện biên về chuyển vị sẽ linh hoạt hơn. BC về lực sẽ ko đặt được trong một vài trường hợp
@hungnguyenvan61315 жыл бұрын
Anh ơi, cái này có áp dụng cho composite được không?
@vandangtran64545 жыл бұрын
Hung Nguyen Van áp dụng được bạn ạ. Thực tế là mình dùng để làm dầm timber composite
@gauravpatil12997 жыл бұрын
can you show procedure of encased stone column in abaqus
@structurelearninghub33405 ай бұрын
Why didnt you use zero thickness interface element to simulate this
@vandangtran64545 ай бұрын
Hello, this is the simplest
@cuongvan11474 жыл бұрын
Anh ơi có thể cho em hỏi, em đang thử mô phỏng dán 2 vật giữa một vật mặt phẳng với vật mặt cong bằng băng dính 2 mặt. Vật có mặt phẳng sẽ bị cong theo mặt cong kia làm sinh ra ứng suất và làm bong băng dính. Băng dính thì em bỏ qua và định nghĩa dính hai bề mặt bằng interaction Cohesive behavior. Trường hợp của em là crack mode I. Vậy mình lấy mấy cái thông số Knn Kss Ktt với điều kiện phá hủy từ đâu ạ. Em xin cảm ơn!
@vandangtran64544 жыл бұрын
Hi bạn, bài này mình lấy các thông số về độ cứng K, cường độ t và chuyển vị phá hoại bằng cách khớp kết quả mô phỏng và thực nghiệm, bằng cách thử nhiều lần các thông số này đến khi tìm ra đường cong hợp lý nhất so với thực nghiệm
@cuongvan11474 жыл бұрын
@@vandangtran6454 Em hiểu rồi, cảm ơn anh đã trả lời ạ!
@mohamedsherif40962 жыл бұрын
hello, what is the cohesive material used? the cohesive material I am using in my model is S&P Resin epoxy adhesive of 220. how do I get its input parameters? thanks in advance.
@vandangtran64542 жыл бұрын
Hi! the cohesive material is MUF. For capture the parameter's material, i realized the experimental shear test (like model), then constructed this model. finally, vary parameters of CZM in order to approximate the experimental curve (just relative shear displacement/load curve) in comparison with the model curve. Regards!
@johnchen20224 жыл бұрын
Hi, when i used explicit solver to solve this model, the job went aborted and show "Surface based COHESIVE BEHAVIOR cannot be used for contact pair interactions. See the surface interaction named INTPROP-ADH." Could you give me some advice to fix this problem or some suggestion about modelling glued failure with explicit solver? thanks.
@vandangtran64544 жыл бұрын
Hi! you can use Surface based cohesive behavior in ABAQUS/Explicit but you should change some conditions, for ex. using node-to-face instead of face-to-face. for more infors, you may find out in the ABAQUS document/ Abaqus Analysis User's Guide/ Interactions/ Surface-based cohesive behavior. Good luck!