GM 6L80 removal Step By Step converter failure

How to remove a 6L80 in a 4X4 pickup Step by Step

[@robertnevarez7599]

Twenty minutes in and you’ve accomplished by removing so much and so carefully, mush respect .

[@expressautotransmissiondav4207]

Thank you i definitely enjoy my work

[@willstrong7911]

Man you are a saint. I can’t even begin to tell you how much this video helped me out. My transmission just blew up on me in my ‘15 Silverado with 152k miles. However I just had a baby recently and I’m in my off season for work, so I don’t have the money to take it to a shop. Followed along with your video and got my 6L80 pulled. The most I have ever done before is change a starter and brakes. So I am not a mechanic by any means

[@expressautotransmissiondav4207]

Thats awesome glad to hear it helped and congrats on your first transmission swap and baby

[@familyguy5081]

2015 Sierra 1500 4x4 here, yup, 160k miles and converter went out. Pulled transmission myself using these vids. Can't begin to say how much money I saved. So grateful.

[@Butfucker300]

All you did was swap it? Any reprogramming?

[@Chrismckinney1]

💪🏾

[@familyguy5081]

Appreciate this, immensely! Pulled my own 6L80 from my 2015 Sierra 1500 4x4 with almost zero issues. Only one exhaust manifold bolt was a severe pain but I ran up and purchased a bolt extractor and slid a 14 mm over the nut on the driver side and hammered it in good and tight and used impact to back it off without damaging the studs.

[@titanjake8640]

Bless you I just done this 2xs in my 2009 avalanche for a failed TC 2xs!!! Literally last night on my back in my yard. I am a pro now! Lol All jokes aside, great video. I wish i had a lift.

[@darrinfaulkner8911]

I am witnessing pure skills of a mechanic. Thank you for the video I just bought a Torque Converter yesterday for my 2011 Ford Fusion. My car woud stop accelerating in the middle of going up hill a with major traffic coming behind me not to mention I was hearing metal grinding sound and smelling something burning possible from friction. I have 187,000 miles in my car I studied and came across possibly a Torque Converter issues. I just had a used transmission put in my vehicle on April it was gamble and it could've been worse. I will have my mechanic replace it and hopefully that'll fix my acceleration issue, thanks again for the video sir.

[@Meredithbvb]

Thank you so much for uploading this 🙏 first time removing a transmission and this video guided me all the way through it

[@expressautotransmissiondav4207]

That's awesome..it was a blast to make as well

[@leviscott8519]

Very helpful video Brothers! One thing I would add in flush out those cooler lines before jambing in the rebuilt trans. Nice video on getting in there on every step! Good Energy

[@kabzooj88]

I'm taking this top bolts out and don't even want to think that I have to bolt it back 🤦. Good video guys. Thank you for your time and experience.

[@expressautotransmissiondav4207]

Thank you it was a fun one to film for sure

[@kd-rw6bg]

​@@expressautotransmissiondav4207nice video. Can you swap a 2013 avalanche 4x4 ltz 5.3 black diamond tranny with a chevy silverado 1500 4x4 ltz 5.3. Both have 6l80?

[@josecanas2737]

Amazing video. Tomorrow am doing my first Rear main seal on 2018 escalade and this was very helpful since i have access to general motors service information but is not the same as watching somebody do it . Thankss

[@expressautotransmissiondav4207]

Absolutely glad to do it

[@silversled123]

Thank you for this video. It is by far one of the most comprehensive I've seen. Nice job.

[@expressautotransmissiondav4207]

Thank you for the support we've had a lot of fun making these videos.

[@jesusbleak7781]

Lol no help what so ever

[@maddawglynn]

Loving the video brother. I lost audio around the 6:00 mark. Anyone else having this technical issue?

[@stever7638]

Yes, I lost audio for awhile, great video though!

[@jasonwakewich121]

Lol your custom in house hook tool is awesome. I have a lathe in the shop so i have a hooked rod for dealing with swarf its like 3 foot long worked perfect moving stuff on the upper bellhousing bolts

[@expressautotransmissiondav4207]

Heck yeah thats awesome

[@Cocora22]

Well I think you are a genius. I can’t even begin to imagine taking that off let alone reinstall it.

[@expressautotransmissiondav4207]

Lol they can really be a lot of fun

[@Cocora22]

Was wondering if you might help. I realize it’s a stretch diagnosing something long distance. I would appreciate your opinion very much. I have a 2018 Escalade, 26,500 miles has brand new tires, I thought it might help or solve the issue. Didn’t . It may be 2 issues or it could be related? The truck has a constant vibration at all speeds, but it also vibrates slightly or idles roughly at full stops. The engine feels powerful with no lags in acceleration. Very occasionally I notice a clunk when the truck shifts at a very low speed. The vibration is noticeable on the steering wheel and the seat. 2 dealers have told me that’s the way the truck is suppose to run. I asked them why it didn’t run like that brand new and one said , “ We can certainly take a look. I can have the shop foreman take it for a ride. Unfortunately, you are correct about one thing, and that is that we often get complaints for ride quality such as this. As mileage increases, components become more broken in.. and in turn, yes, can begin to not feel up to the same quality or smoothness that they once had. If the transmission is feeling like it is either sluggish or slipping, a transmission fluid change can be tried yes, and that may certainly could help. But at the end of the day, if the vehicle is operating in good condition, and no components are showing signs of degradation or failure, then really it may not be something that cannot so simply just be "fixed." “ Personally I think it’s an excuse to avoid all the work that might be necessary to accurately diagnose the problem, but I’m not a mechanic and have no idea how to figure out or diagnose issues. However I do love watching professionals like you perform amazing repairs. Thank you!

[@expressautotransmissiondav4207]

To diagnose something like that would definitely be very involved and you are correct I think current opinions may be far fetched or even completely wrong. However if I was to start to examine a vehicle with that type of shake I would be starting with visual inspections. I would look at motor mounts and we'll as check fluid levels and conditions on all sumps. If you have the same or very similar shake at idle as well while moving I would suspect something around engine area or converter. Another area of concern is the idle vibration. I would be reaching out to other qualified shops in your immediate area for a second opinion. Having someone else look at it but not touch it.

[@Cocora22]

@@expressautotransmissiondav4207 thank you for your time really appreciate it. That gives a bit of information when I get to the shop next week. At least I’ll have some intelligent questions to ask.

[@nathanmerrifield3739]

So if im pulling a 6l80 transmission in a 2014 1500 chevy to replace torque converter, transmission seems good from what i can tell, should i flush the transmission and change filter or just replace fluid lost and throw it back together? Truck has 180,000 miles with no record of previous flushes or being replaced. Given the fluid is pink and clean its been done at some point id imagine. Truck just has occasional shutter and vibration and then fluttering rpms at highway speed. Thank you in advance. Great video!

[@john-wb2vs]

Thats how it's done, Plan on doing this task on a 08 DENALI XL laying on my back in the garage. Might have to rethink that? Great "realistic" R&R of a trans/transfer case! Thank you!

[@expressautotransmissiondav4207]

Glad to help

[@stevensilva1350]

An absolute wealth of knowledge. It’s a shame this 6l80s are such trash designs. Even if I watched this 9 times over. This job should be left to someone that specializes in. Converters an transmissions. There’s so much that goes into it oh my goodness.

[@jaybilawchuk2225]

Speaking of trash, have you ever had to deal with the shit 8L90 yet? lol.

[@fishman80]

you have to change your fluid every 40 to 45,000 miles regardless of what the book says. These trucks you have to follow the severe service intervals or better. I’ve done that and put a lower thermostat in it many miles ago and I’m at 196K on the factory 6l80.

[@kpd3308]

I think I'm going to spray some penetrating oil on the bell housing alignment pins every time I change the engine oil.

[@cameracamera1319]

Lol. You troll. I even have trouble when the engine and tranny are laying on the shop floor. My children like the entertainment.

[@NORCALPYRO_]

Damn so it took you guys about an hr to drop it nice💪💪

[@RobertBrown-gu1rr]

NOW, LAY ON YOUR BACK AND DO IT! 😂😂😂

[@richardgreen7939]

Great video, just replaced my transmission but didn't solve my problem.. not sure if it's rear diff or transfer case. When starting out in drive there is sometimes a second delay before the vehicle starts moving after hitting the accelerator, this happens when at a stop sign or starting out. Occurs about 50% of the time. Any ideas on the issue would be appreciated? Thanks

[@masongierisch912]

same. did you find the problem?

[@hochhaul]

They didn't re-use the original torque converter did they?

[@ProModRick]

Great Video it helped me do the job. I got the trans swapped only problem left is the vent lines one goes to the transferase the other to the trans were does the third go? 2014 Tahoe thanks

[@radggs6961]

Although I will never take on this job, need tools and a shop, it tells me just what someone else is going to do, and it makes me so much more mad that this has to happen to my 44k mile 8spd. Thanks 🏁👍🏾

[@calicobra956]

If you don't mind me asking. How much would your shop charge for a torque converter replacement?

[@devil0311doc]

Me too Please 2017 Silverado 5.3 L First Transmission blown at 60,000, put a brand new one, Had a lifter stuck at cylinder 7, Told i needed to put a band aid on it by repairing left bank for $6000 or engine rehaul for $15k said no thanks did a dod/afm delete myself at home kept everything stock and replaced the camshaft for a gm delete cam because i had a chunk of metal that was taken out of it. That was at 100,000 miles ran great if not better then at 120,000 miles second transmission went out again torque converter failure and check ball#3 stuck in plate metal all through. Currently rebuilding my transmission myself i won't let anyone work on my truck from this point on. oh when i called gm about my engine and i complained on bbb website they called and offered me $1500 gm certificate towards the purchase of another silverado i laughed at them.

[@orlanmedina3693]

Awesome video, mine is a 2007 yukon XL 5 3 4X4. No problems at 191k miles, no?idea of it was replaced. Just bought it. Only issue is lots of leaks, most likely the o-ring from the oil pump, seal and clutch o-ring the one in the shaft. will need to be replaced Im only planing pn use it like once a week. So im hoping it will last me lots of years more. After replacing those, and didnt know about the thermostat bypass. Dont know why GM put it if it fails?

[@jasonwakewich121]

Good video looks like you have a lot more room to get to everything im just struggling hard on the floor with a super muddy truck but i decided to leave the tcase on both the donor silverado and the dead sierra. Is it just me or was 4l80e's easier?

[@coryrichter1269]

Great video!!!! Getting P0741 after swapping converters. Although shudder is gone, now I’m having this code. If the trans shifts through the gears and the converter locks, does that mean all the connections are fine? When the CEL shows, it does the no 6th gear, no converter lock scenario. I’m hoping I don’t have to swap converters again.

[@TheJoedude02]

After 7 months, any updates? I'm genuinely interested. Thanks

[@billsharpe2746]

That is a well-done video, and your work is excellent as well, are you going to upgrade the torque converter? I wrap my crossover pipe 2x that runs under the trans pan with a heatshield rap, to try to lower the heat in the transmission. When I change my fluid I used the best fluid that I could buy.

[@expressautotransmissiondav4207]

That's awesome. I don't wrap them unless its a hotrod. I did upgrade the converter to a precision billet face. Thanks for watching we have a lot of fun making them..

[@hochhaul]

The 6-speed in 2014+ trucks runs hot because they came from the factory with a thermostat that causes the hot fluid to bypass the transmission cooler until it reaches a certain temperature. That's why they're always at 190 degrees or hotter. If you want to reduce those temps, there a multiple ways of doing it. GM has a different thermostat out now, there are aftermarket bypass thermostats made specifically for the 6L80, or there are ways of modifying the original bypass (not recommended but many guys do it).

[@joshdavis8447]

Audio is gone during trans dismount. I don’t hear an explanation for prying on the machined bell housing surface. Those pry surfaces often work well, along with an up and down shimmy of the Jack.

[@lestapp7845]

Excellent tutorial. Thanks for sharing.

[@expressautotransmissiondav4207]

Anytime

[@joel.3112]

Loved the fluid is black ! Oh iam sorry can I say that? It's crazy what the world has become

[@RaulHernandez-jg7cr]

I just removed mine at home for my first time removing a trans. Video was very helpful. But do you have one to install it back in. Question how hard is it to line up the fly wheel to bell head when going back in with new one?

[@expressautotransmissiondav4207]

Unfortunately we don't have an install one but we do have one in the works. As far as the line up it's not bad at all

[@BussinMindSet]

I feel like if it’s just the torque converter pulling the engine and getting to it that way might be easier?

[@expressautotransmissiondav4207]

Unfortunately its more of a pain to do it that way but on some it is easier.

[@mattl1576]

Would spraying some penetrating oil on the dowel pins early on in the removal process help separate the trans once you get to that point?

[@expressautotransmissiondav4207]

It has never helped me but anything is possible

[@robertnunez5036]

Very good video,my question is can I swap 2015-Into a2009

[@expressautotransmissiondav4207]

I'm not sure but I'll check

[@Leekautorepair]

I use an air hammer for the dowel pins

[@expressautotransmissiondav4207]

I've done that a few times and it does work

[@westhomp1721]

Does the transmission have to been in neutral when removing the Torque Converter bolts and is it necessary to make marks on the TC and the driveplate?

[@expressautotransmissiondav4207]

Nope does not have to be in neutral. And nope doesn't have to be marked

[@rustyshackelford7651]

Good video, you lose audio in a few places tho. Like around 26:19 I couldn't get the truck in neutral last time and had to put everything back together. Saw RainmanRay just took the shift lever off the transmission and used pliers to turn the lever into neutral? How do you get it in neutral if you put it on the jack stands in park? BTW don't know if you mentioned it but when you're showing the shift lever at 26:22 the shift cable bushing looks to be nearly wasted. THEY WILL EVENTUALLY FALL OFF AND YOUR COLUMN SHIFTER WILL BE INOPERABLE It happened to me. Sketchy af. And will happen at the worst time and place. There's a kit to fix them, a little aftermarket bushing and a snap clip. You gotta drill out the original hole tho some. it's pretty easy. Always check this bushing tho, not fun to have the shift lever fall off while you've just shifted into drive and the truck is running and now you can't shift back into park. Should have been a recall on that bushing.

[@SaulMendez-ky1pg]

What were the symptoms of the failing converter?

[@DriftKilles12]

If you listen and actually pay attention instead of having your head far up your ass. You would know, that he said it.

[@mattsarvis8879]

Whats your opinion on the transmission cooler thermostat that bolts on the side(Bypass kit), im seeing lots of people buying a kit to modify the thermostat inside that block and it drops the transmission fluid temperature significantly

[@stevepoulin8964]

I hade to my 6l80e transmission run hot n it did work unfortunately I waited to long its on its way out 2015 silverado

[@longbow60435]

You mentioned that the truck was shaking,,,I have 93 chevy van that shakes in park and neutral to ,,,after a rebuilt trans and new TC,and numerous other parts that I have installed,,could it be I have a new bad TC? Something feels out of balance.

[@expressautotransmissiondav4207]

That's possible also another thing to check is a miss if you have a ignition miss it can make an engine vibrate.just throwing that out there

[@adriano3578]

Are these transmissions the same in 2017 Silverado?

[@IntegraGSR5]

Question please. I can start the engine after techm replacement before bringing it to the dealership for reprogramming?. Thanks in advance

[@expressautotransmissiondav4207]

Absolutely just don't try to drive it

[@IntegraGSR5]

@@expressautotransmissiondav4207 more questions please. Is it ok for me to shift in all gears to make sure my installation is right before even towing it to the dealer ?. When pulling the truck onto trailer. Can I shift to neutral, just to make it easier to winch it up. Sorry to bother you, I just want to make sure if its OK to do so before the tow guy comes over next week

[@expressautotransmissiondav4207]

Yep

[@joecorrie1]

Great video I did with the camera did a good job

[@thefightgame6722]

Brother ,!, I have a 2014 Chevy Silverado with a 5.3 , well I changed the trans filter and fluid and even put some shudder fix in it. Well the truck will drive now and does good until you get to overdrive then it shudders really bad..the trans magnet did have quite a bit of sludge..the truck has 140 thousand miles.. before I changed the filter and fluid the truck would come to a stop and would act like it was in neutral while you was in drive..all this happened in 2 weeks of time.. I really think the tourge converter started this mess.. as of right now I’m still riding it and it does good until it shifts to overdrive.. what would you recommend... another filter change or a complete rebuild or maybe a torge converter replacement.. Thanks brother

[@expressautotransmissiondav4207]

It's time for a rebuild. This is a common scenario for this transmission. We're starting a build series soon on the 6l80 family of transmissions, if you want to follow along we're gonna show how to disassemble and do a complete rebuild.

[@thefightgame6722]

@@expressautotransmissiondav4207 sounds good brother. I’m actually in the process of taking out my trans today. I’m fighting with the two top trans bolts at the moment. So I’m trying to watch to see what you did. Lol

[@expressautotransmissiondav4207]

Lol I use a long 1/2 to 3/8 extension with a deep thirteen socket to remove the nut then a deep 15 wobble to remove the main bolt

[@mchockeyplayer25]

Awesome video man. Helping me out a bunch on my first trans drop. Any idea of why my torque converter won't spin freely/easily?? I was able to get one nut off but can barely move it to get to the other two. Any ideas would be great. (Trans has a neutralizing problem/cracked drum situation) according to my mechanic

[@expressautotransmissiondav4207]

There are three converter bolts if you can access the front crank bolt you can use a 1/2in ratchet to turn the engine over to get to the next bolts. Also not having any background always make sure the battery is disconnected and if the vehicle is on the ground use good quality jack stands safety is number one in my shop.

[@hybridmusclegarage4590]

Awesome video . Great content.

[@omargarcia6270]

Does it matter how the drive shaft goes back on? I didn’t mark it and I did the transmission swap (video helped a ton!) and now my truck shakes. It didn’t at all before. And I just installed a new drive shaft OEM GM part. And it still shakes. Your help would be great

[@expressautotransmissiondav4207]

Ok first thing wear do you feel the shake

[@omargarcia6270]

@@expressautotransmissiondav4207 I feel the shake in the drive line. In in the floor. Steering doesn’t shake wheels are balanced. Etc. you can feel the shakes at certain speeds and you basically can hear the shake like a hum per say. Before I did the trans swap the truck drove smooth no problem whatsoever. Did the swap and out the original driveshaft back. And I could feel a shake. Did a 180 on the drive shaft and still felt a shake. Put new u joints still shook and a more than before. So to insure it wasn’t a bad install of u joint got a whole new shaft. OEM GM and still shakes. 2014 Silverado 4x4 I

[@expressautotransmissiondav4207]

Would you mind reaching out to me at my shop during business hours I'd love to try to help

[@omargarcia6270]

@@expressautotransmissiondav4207 I don’t mind what the number? I’d go by but your in Chicago snd I’m in Texas

[@expressautotransmissiondav4207]

I'm actually in Baxter springs Kansas

[@bigdaddy9864]

nice video the sound needs some help .but any way these transmissions have all the same issue "HEAT" that dumb thermostat that control the trans temp are set to high and GM knows it!!! they swiftly & quietly replace that stat with a repayment one with a 50* lower open rate in later years .The trucks 2014-2017 run a 200* + and burn up the fluid & converter. The GM REPLACE stat now open's at 160*. I have a 2014 and bought a bypass plug that replaces the stat my truck run's now at 140*-150*.

[@lyquidsnake4202]

Nice video. What's the average cost for the rebuild? Not sure if it would be worth the rebuild or a new truck.

[@expressautotransmissiondav4207]

My units are around 3500 for rebuild

[@RZRQUACK]

Theres 7 bolts on the bellhousing correct?

[@Kennywxyne5400]

Good Afternoon. I’ve recent got my converter changed and now my fuel Gauge isn’t working , is it possible they didn’t hook something back up around that area ?

[@expressautotransmissiondav4207]

Very very unlikely

[@johnmorgan8309]

What is a ballpark cost for this service in your shop?

[@utrocker7]

if you do a complete 6L80 trans swap do you need to relearn or program the trans? or is it a bolt on plug and go? my TC and trans went out at 113K on my 2016 sierra but i found a 2018 6l80 from a silverado with 5K miles on it. (truck was totaled but trans and TC still in good shape). curious if i need to program anything...

[@expressautotransmissiondav4207]

I would program it after the swap also make sure the cooler is clean

[@utrocker7]

@@expressautotransmissiondav4207 thanks for the cooler reminder. I’ll check that as well.

[@expressautotransmissiondav4207]

Anytime

[@jeremyallen3448]

We replaced with used transmission. Getting no communication while trying to reflash tcm in used transmission. Is the TCM considered an internal part of the transmission and should be under warranty or is the tcm considered seperate from the transmission warranty. Technical question but just curious how most technicians view that.

[@expressautotransmissiondav4207]

I view it as the tcm is bolted to vb. If it wont program probably wrong tcm for specific vehicle. I would check to see which tcm.you have and which one is needed.

[@jeremyallen3448]

@@expressautotransmissiondav4207 thanks for quick response we will look into it

[@georgedurden9835]

What tool do you use to remove converter bolt, when the only access is through the starter hole, no shield to make access easily?

[@expressautotransmissiondav4207]

What's the application

[@robertlaxen3839]

did you do a rebuild or swap in a new converter

[@expressautotransmissiondav4207]

Rebuild

[@funny524k]

Does the transmission need to be rebuilt my torque converter just failed on my 2015

[@expressautotransmissiondav4207]

Pull the pan check for metal if it has any metal in it it needs rebuilt.

[@funny524k]

@@expressautotransmissiondav4207 thanks I am working with GM my trucks transmission started shifting bad they pulled the pain said it's full of metal and needs a remanufactured transmission I bought the truck brand new always had it serviced at the dealership there 91k on it and it's a 2015 I have owned many trucks with the 4l60e transmission and never had a problem I was told by a few people it's a design issue would you agree with that statement?

[@stevepoulin8964]

Thanks my 6l80e going

[@rockabichebel]

hello plz I have 4l60e on 6.0l gen 3 I have a transmission problem R n 1 working verry well 2 n 3 n 4 don't have a power on hight Rpm more than 2000 start to slip when I give a little throttle more than 2000 rpm starts to slip shifting down slow shifting a little by hand i have slow shifting between 1 n 2 , 2 n 3 , 4 with slipping when rpm start to more then 2000 I have rebuilt it and same problem you think torque convert ? thank you

[@expressautotransmissiondav4207]

Need to get a pressure gauge on it and see what is going on. A scanner to check epc voltage and a gauge to check line pressure.

[@rockabichebel]

@@expressautotransmissiondav4207 ok tomorrow I'll cheque with a gauge

[@stevenlemay9004]

Did you have any issues lining up converter with fly does converter line up in a certain spot

[@expressautotransmissiondav4207]

It doesn't line up to a certain spot. However there is one converter bolt hole that is oval shaped if you install that bolt first the other two will always line up. If not then you have to leave the bolts loose till all three are started before being able to fully tighten them.

[@justalsa421]

My trans start to over heat would the torque converter be the problem

[@expressautotransmissiondav4207]

It's possible but truly needs to be tested to be sure

[@justalsa421]

@@expressautotransmissiondav4207 the a/c condenser got replaced and the trans cooler line hook up to it idk if it leak fluid . And if they top it off again or not

[@reynaldojavier1824]

Good job

[@jraydelatorre]

I have a question average price or a ballpark price about what does it cost to get set up to do vacuum testing on a valve body mainly the 4L 60 E test play and test stand I have done what sonnax told me to do and made the calls so far I still haven’t got no response so I resorted to text messaging with Transtar The only response I got seem to be an electronic generated message kind of weird

[@expressautotransmissiondav4207]

I think they are around 300 if you want I can get a price to sell you a full setup.

[@jraydelatorre]

Soon as I get over this medical setback I am experiencing I would certainly be interested i may be facing A three month period of time laid up in the bed from surgery this is a tough decision to make when the doctors are constantly trying to talk me out of it but I am experiencing severe neck and head pain it’s nothing new I broke my neck several years ago and I’ve had two surgeries it’s just unbearable I can’t deal with it anymore And the problem is yes there is hardware holding my spine together but the spine is still broken and after all of the MRIs x-rays they keep saying they can’t see what’s causing the issue saying everything is good as it could be and the hardware is still intact I may be Contacting a Nuro carinal specialist can take a second look and also look at the skull carinal plate

[@expressautotransmissiondav4207]

Holy pickles that's a big undertaking. I wish you the best if luck with the surgery's and fast recovery

[@keithmackenzie9719]

Did you mention the year and how many miles on that GMC?

[@expressautotransmissiondav4207]

I don't think so

[@xravenhairsexgod]

Front bumper fog lights dictates its either 2014 or 2015. I have one at 134K with no problems yet but I'm considering a converter swap now after this nightmare scenario. Or sell it unfortunately.

[@wyatthurley8707]

Great video! I have a couple questions. Are there any torque specs on any of the bolts when reinstalling? And is any loctite needed on any bolts when reinstalling? Thanks

[@expressautotransmissiondav4207]

I use loctite on all of my converter bolts. I also like to use factory specs for my tcase bolts as well as u joint strap bolts if you need any of those specs lmk and I'll get them to you.

[@wyatthurley8707]

@@expressautotransmissiondav4207 yes please! I’m swapping my torque converter next weekend. Thanks so much!

[@expressautotransmissiondav4207]

What's your year make and model I will get factory specs

[@wyatthurley8707]

@@expressautotransmissiondav4207 2017 Silverado LT

[@expressautotransmissiondav4207]

I'll get the specs in the morning when I get to the shop.

[@lonewolfeman]

curious, what was your actual time start to finish to tear out the tranny as shown ? Great video btw.

[@expressautotransmissiondav4207]

Averages about an hour and a half to remove and disassemble

[@lonewolfeman]

@@expressautotransmissiondav4207 well your video was about time, it must take a lil longer than that ? There's a lot of fussing around under there, thats amazing.

[@expressautotransmissiondav4207]

Lol thanks

[@lonewolfeman]

@@expressautotransmissiondav4207 I own a 2016 GMC Sierra with 185,000 Kilometers or around 120,000 miles on it , it shit the bed last week, warranty up at 160,000 Kilometers. It wouldnt shift out of low gear. Fucking Junk . Last GM product for this sorry fuck.

[@expressautotransmissiondav4207]

Damn sorry to hear that. They definitely have been having a lot of issues for sure..

[@cameroncabrera6476]

I was going to put the starter seal back in but now u don’t want to

[@stevecampbell7620]

David I know the torque converter is a weak link. Have no problem with my 2018 Silverado yet, what is your opinion of replacing the trans cooler thermostat with a Sure Cool to lower trans oil temperature?

[@expressautotransmissiondav4207]

I do it on every rebuild or service we do my shop.

[@matthewavery7677]

Do you have an install video by chance?

[@expressautotransmissiondav4207]

Yep we have one on the channel. I don't know how to post the link but it's on the channel lol

[@josephrajkumar5193]

Would a 1cka replace a 9cka?

[@zeitlerusmc]

Your guys commentary was painful to listen too, but the video was good, other than the sounds randomly going out.

[@jayer-su3hu]

Side question Does anyone know what issues if any there may be if I eliminate the exhaust pipe that runs under the transmission pan? I'm sure that contributes to the death of these transmissions along with making fluid and filter changes more difficult

[@351cleavland]

I dropped the pan for a fluid change, added a drain plug and then used some reflecta-heat with adhesive to the front and side of the pan in order to block much of the heat soaking into the trans pan. I also installed a trans thermostat bypass fro Superior. That and the Sonnax zip kit made a HUGE difference in overall shifting and cooling.

[@expressautotransmissiondav4207]

Heck yeah that's awesome

[@joerivas9847]

I want to buy a used 2014 sierra/silverado to replace my 2000 sierra 4x4, now I am having second thoughts......

[@eriknash8783]

Why does audio keep going away?

[@expressautotransmissiondav4207]

That was a total turkey because of copyright issues.

[@rudyromero371]

Make it easy on yourself when taking off starter remove wheel well cover first

[@quinnhaynie7767]

I spy a factory drain plug on the tranny, sure would be nice if they put those on from the get go

[@BrianCooperFishing]

Everything is 19.99 on TV! That's your price! Lol

[@jessetorres6317]

What the hell happened to the audio?

[@elms1319]

Sway bar 🤯

[@JoeyWilliams89]

Just constructive criticism…. The audio was killing me. It was good, shitty, silent, good, shitty and so on. Made it hard for my adhd ass to pay attention to what was going on because I was too focused on the audio being hit and miss.

[@expressautotransmissiondav4207]

Sorry about that

[@datz_nice_805]

Rubber mallet dead blow hammer

[@corey5291]

did you guys drain the transmission first?

[@mikem5475]

the video was not professional at all. You need to get better audio and better camera work. Camera man is jumping around like he's drunk

[@travisclarke9214]

He's clearly trying to get a good shot of the area being worked on. Audios probably gone cause he had a radio in the background and yt sucks. Post your video up or gtfo

[@mikem5475]

@@travisclarke9214 The criticism wasn't directed at you, it's amazing how sensitive you are to constructive criticism directed at someone else's project

[@seanbishop9273]

Mike is lame

[@mikem5475]

@@seanbishop9273 you're special, that's for sure