perfect . I love it. great job just lost the motor in my 600 rush last night. time for a tear down with my son.
@gobigparts Жыл бұрын
Great learning experience. Sled is still running great.
@rickmattson6780 Жыл бұрын
Thanks for the video
@larrywarner9314Ай бұрын
Obknow this is a 2 year old video, make sure you test the oil pump for the oil injection, first full tank of fuel mix it at 50:1
@gobigpartsАй бұрын
Great point and I did both. Ran great the last 2 seasons.
@scottdillon7452 Жыл бұрын
Love the video, I’m going to be doing same thing with mine
@JasonRidesmoto Жыл бұрын
I'm eyeing a 2012 Rush 600 that has 10K miles on it... Might have to do this 😅
@edwardabrahamiii3742 Жыл бұрын
Im starting to like Polaris!
@edwardabrahamiii3742 Жыл бұрын
Earned a new subsciber i want to rebuild a 600 cfi in a 2014 polaris indy 800sp frame
@gobigparts11 ай бұрын
That you Edward. We love Polaris sleds and I love teaching my kids how to do things.
@edwardabrahamiii374211 ай бұрын
@@gobigparts nice dude! I'll show my boys how to do things myself.
@Siim-ToomasSepp8 ай бұрын
Great video! How many hours did it take to rebuild?
@gobigparts8 ай бұрын
Don't remember. We took our time and probably took a week of nights and then put it back together and back in over a weekend.
@larrywarner9314Ай бұрын
Free advice, remove the seat , gas tank, that stuff needs to come off then the airbox you'll see wut i mean when you take all that other stuff off it opens up so your not fighting with no room to take the engine off
@gobigpartsАй бұрын
I did think of that after the fact. Great Advice for sure. Been running great the last 2 seasons.
@lukestrobel12452 жыл бұрын
Hello, Really enjoyed the video. Where do you send the cylinders to get plated?
@gobigparts2 жыл бұрын
Millinnium
@thomaskilligvuk1124 Жыл бұрын
How do you set up your power values in your engine
@gobigpartsАй бұрын
These ones were manual vavles so just cleanned and put back in.
@StephenBond-s2i11 ай бұрын
How did you clean the old sealant off case before reassemble?
@gobigparts11 ай бұрын
Scrapped it with a plastic putty knife and finished it with a razor blade being careful not to dig in an put any deep scratches. Went over it with a rag with some brake clean on it.
@lukesmith914411 ай бұрын
Needed all that work after only 4400 miles?
@gobigparts11 ай бұрын
When you buy something cheap there is a reason. You don't always know how previous owners took care of it. With aything in life failures can happen. I happen to have aothere 600HO with over 10,000 miles on it.
@lukesmith914411 ай бұрын
@gobigparts I have the same motor with 6000 miles so this videos existence made me a little worried lol
@coreymartin7068 Жыл бұрын
Do you prefill the cavity of the crankcase where the crankshaft gear meets the water pump gear with any oil?
@gobigparts Жыл бұрын
I did not. Not sure if you should or not. Mine does run good now.
@coreymartin7068 Жыл бұрын
@@gobigparts Okay thanks! I just assembled my 600 CFI bottom end and didn't either, I went through the Polaris shop manual and see nothing about requiring to do it. I usually work on ski doo/sea doo and those machines require an oil bath.
@thomaskilligvuk1124 Жыл бұрын
How do you set your power value when putting it on the engine
@gobigparts11 ай бұрын
Not sure wha your asking. Power Value?
@thomaskilligvuk1124 Жыл бұрын
How do you set up your power values in your engine
@gobigparts11 ай бұрын
These ones are spring return and pressure activated. So no need to set, just clean.
@screamdoctorАй бұрын
You failed to spin test the bearings. You failed to attempt to clean out the piston rod bottom bearings and the crank bearings on either side of the damaged piston. High chance of metal filings in those bearings.
@gobigpartsАй бұрын
Did that off camera, cleaned and oiled.
@joshuadeschenes48742 жыл бұрын
Hey just out of curiosity, how many miles were on the motor when you rebuilt it.