This video will show you how to remove the impeller from a Goulds J10S Shallow Well Pump
Пікірлер: 56
@cbt196010 күн бұрын
Thanks, very informative on removal the impeller
@toebarsrealm3773 Жыл бұрын
Thanks for the info! I used you vid as a guide for replacing my motor last fall. Sharing it with my dad for a repair this spring.
@lionheartapologetics49142 жыл бұрын
Thanks for explaining how to lock the driveshaft by removing the capacitor! That was the one thing I couldn't figure out by myself. God bless!
@zeppone40452 жыл бұрын
Ur Welcome……
@bnhamilton3 жыл бұрын
This is an AWESOME video! You don't leave anything out, and don't waste time on anything that's not important. Thanks for the help. Got to go finish my pump now.
@zeppone40452 жыл бұрын
Thanks
@robertnastasi4738 Жыл бұрын
15 videos. this was the one Thanks
@dennisoates Жыл бұрын
A well done video, my Goulds pump has deep grooves in the impeller shaft housing. I have lost pressure. Is the problem with the grooves? I use the pump for irrigation. thanks
@rohumco14035 ай бұрын
saved me a LOT of frustration
@esaysjourney91688 ай бұрын
Excellent
@joequillun77903 жыл бұрын
Thanks for the video. I couldn't remember if the impellers were LH thread.
@davebrenner39074 жыл бұрын
Thanks for the how-to! I just pulled one of these out of service on 5/5/20 and installed an old J5S in its place temporarily while I figure out what the hell I (stupidly) did to the J10S. It's a "comedy of errors" sort of story... My submersible pump went bad last Saturday after a dozen years in service. The motor is kaput: common/run and common/start were both in the hundreds of megohms. Pretty cut and dried. So we went out and bought all the stuff we needed to change the damn thing out. While doing the changeout, I thought I heard water flowing back into the well through the now-vacated pitless adaptor. It wasn't (a check valve at the buried side of the pitless prevents it), but at that point in time I thought it was, so I closed the valves on the storage tank, which is hundreds of feet from the well head. 4+ hours later, I discovered that I had neglected to turn off the breaker for the J10S. That discovery came in the form of finding the J10S hot enough to cook on and making an obnoxiously loud buzzing noise not unlike the alarm on a septic system. After cooling down overnight, it still buzzed, so I knew I was screwed. If I am reading the service manual correctly, the winding resistances check out, so I think the trouble is in the impeller area (hence my finding your video), which is a relatively inexpensive fix and well worth getting a workhorse like the J10S back in service. Plus, it's the newer style pump with the white circuit board in the motor, so I can probably do a rebuild kit without also having to replace the front casing. But I will need to open it up to be sure. In the meantime, I had a spare J5S on hand (because what home owner doesn't keep spare jet pumps in their garage?), so I was able to clean that up and put it back in service. The sooner I can pull it back out the better, though. It's pretty weak compared to the J10S. That is, after all, why we replaced it after only 3 years. (17 years that pump sat in my garage waiting for its moment to shine! haha) I like the profile pic, by the way. "The Hermit" from "IV". One of the greatest albums of all time.
@zeppone40454 жыл бұрын
Hi Dave. Thanks for the comment and hope my video helped you in some way. Being in New Jersey with the COVID-19 lockdown, i used my plenty of spare time to make a few videos to help out with Spring time and turning pumps on in a lot of places.😄 Love Zeppelin 👍🏻
@michaelvandam70864 жыл бұрын
You are a life saver !
@zeppone40454 жыл бұрын
Glad i could help..
@doublebackagain43112 жыл бұрын
@@zeppone4045 Hello I have a 1/2 hp Goulds pump, have pressure coming out of the INLET line. Any idea what is going on? Thanks
@NeilSucalitАй бұрын
Halo sir may i ask what is the size of bearing and shaft seal of J10s goulds pump?
@shandusa2 жыл бұрын
It seems that these J10S pumps have a back pullout design that allows you to rebuild the pump without having to disconnect it from the piping. Have you ever tried that? Thanks in advance
@zeppone40452 жыл бұрын
Nah, u have to disconnect piping to get front casing cover off to get at the impeller. No other way to get at impeller without moving front casing cover. Only thing you can remove from back with disturbing the piping is the motor only itself.. This is why you should use unions on your piping incase you have to work on the pump. Easy to take apart in the future……
@samueltaylor4989 Жыл бұрын
Wrong. You do not have to disconnect piping. Four bolts will disconnect the motor/ impeller housing from the front inlet casting. Just have to disconnect the wiring if necessary.
@davidbarron66893 жыл бұрын
The guide vain is the plastic piece with the rigid and the impeller is the part on to rotor
@joequillun77903 жыл бұрын
I think he corrected himself in the video, but thanks for commenting.
@zeppone40452 жыл бұрын
Guide vane is Black plastic round piece that covers the rotating impeller. The impeller is the round smooth rotating piece. I said it backwards when i first removed it in video. You will see yellow print on screen explaining this. I made this video in 1 take….I dont edit….✍️
@daleb56963 жыл бұрын
Thanks very much. Is this similar to a stay rite irrigation pump? I bought a home with a lake sprinkler system and it has the Stay Rite but the motor just hums n i think the pump is rusted inside and I need to take it apart. Thank great video.
@EdibleEcology2 жыл бұрын
If the motor is just humming without pumping it most likely needs a prime and possibly repair check valves on the suction side. If it’s pumping but grinding, then that’s the bearings
@bullseyeX10933 жыл бұрын
Excellent....very helpful
@zeppone40452 жыл бұрын
Thanks
@straycat3704 жыл бұрын
a big big help,thanks
@zeppone40454 жыл бұрын
Glad i could help. Please subscribe.👍🏼
@jamesa62722 жыл бұрын
I hope my old guide vein is not a snap on one. Lol. I may just have to reuse the old one then. I bought a rebuild kit with a newer one with bolts
@fyrfox200020 күн бұрын
Should have should where you put that wrench
@Joshua56542 жыл бұрын
I have the same pump mine keeps jamming up and then won’t spin I take the impeller off put it back to together and it works for a while then it jams again what is causing this?
@gregorgman3 жыл бұрын
My motor seems to be frozen. I removed the casing like you said, put a socket on the impellor/motor end, it rotates one direction, I believe counter clockwise but wont move in the other direction. The motor does nothing when I turn it on. Any thoughts? Thanks.
@josephsaucedo86913 жыл бұрын
Motor is blown need a new motor sorry 👍👌✌️💯💦
@ldgillette3 жыл бұрын
My pump ran out of water and the impeller and the impeller cover melted. I took the cover off and used some light sand paper to try and smooth the the surfaces. But when I put the impeller cover back on it still keeps the motor from turning. Do I definitely need to replace the impeller? And the Impeller Cover? Or can I fix it by sanding? Maybe the heat from running all day permanently warped the impeller?
@josephsaucedo86913 жыл бұрын
You are right. Some time sanding it works but most of the time it's done hope that helps 👍👌✌️💯💦
@danny62473 жыл бұрын
What about the JRS10 goulds pump. I opened mines. it has a seal leak but it has a flat head screw in the center and boy is it hard. Any tips or tricks for that one?
@josephsaucedo86913 жыл бұрын
Ya the screw is left handed tighten is actually loosening it. don't loose the screw you will never find another one. I'm a pump tec👍👌✌️💯💦
@frankish53143 жыл бұрын
Can you not simply drill and tap the holes in an old style motor adaptor to accept the new style guide vane?
@zeppone40453 жыл бұрын
I believe the casing is thicker diameter on the new casings that use screws. You would have to line the guidevane up perfectly and you might have to use shorter screws.....Good Luck....
@frankish53143 жыл бұрын
@@zeppone4045 Thanks.. I tore mine apart yesterday and I have a guidevane that is secured with 4 screws.. Looking closely it appears as though the case is tapped for both 3 and 4 screws.. I notice that the new guidevanes come with 3 screws? I have ordered the kit and we'll see what shows up.
@leonidesjavier34844 жыл бұрын
Sir,do you have a video on how to replace the bearings of this pump?
@zeppone40454 жыл бұрын
Sorry no video on bearings. Goulds doesn’t offer motor bearings as a replacement part. You need a replacement motor. If you want to have bearing replaced , try an electric motor repair shop or a pool supply. They use a lot of the same type of motors on pool filters. Good Luck. 😉 👍🏻
@leonidesjavier34844 жыл бұрын
@@zeppone4045 thank you
@ralphm62344 жыл бұрын
Do you happen to know the blue color code for these pumps? I need to repaint mine. Thanks.
@josephsaucedo86913 жыл бұрын
At our shop we use ford blue it's close to the original but there is no point code the factory doesn't even no
@nhebert12342 жыл бұрын
At 1:55, you mixed up the guide vein and impeller :)). Great video though.
@zeppone40452 жыл бұрын
If u really watched the video u would have seen that i inserted a message telling everyone that……and it wasnt at 1:55. This is why i make my videos very specific….
@CoSomber3 жыл бұрын
I cant get the cover off like u did before the vid
@zeppone40452 жыл бұрын
Its just corrosion causing it to be stuck. Just take a flat blade screw driver and tap all around the seam. It will loosen up. When you open the seem a little, spray some wd-40 and it will come apart. When two different metals are in contact and exposed to a common electrolyte, one of the metals experiences accelerated corrosion while the other is protected. This type of accelerated corrosion between dissimilar metals is referred to as galvanic corrosion.
@user-wy9gc7nx5x3 жыл бұрын
I have a question about Goulds J10S Shallow Well Pump. Is this one OK with running non stop, exp:24hours/a day, during 1 year?
@josephsaucedo86913 жыл бұрын
Motor need to cool down it will burn up. if you always have water pump will be okay
@WiSeNhEiMeR-13692 жыл бұрын
GUIDE-VANE ... OLD to NEW ... if you need to UPGRADE from the OLD to the NEW ... SNAP-IN to BOLT-IN ... Couldn't a homeowner MARK & DRILL & TAP the required HOLES ???
@zeppone40452 жыл бұрын
Guess u could try, but factory motor adapters that are tapped with deeper holes built into motor adapter..
@advancedanr2 жыл бұрын
6.5 min to explain something that should've taken 2 min max. By the way, the capacitor will not electrocute you, it'll give you a nasty bite but will not come close to killing you unless there's still power going to the pump.
@zeppone40452 жыл бұрын
Better to be specific and take your time. You can always fast forward. As for Capacitor, i am giving a general warning ⚠️ about electricity. No one likes a shock.⚡️⚡️⚡️😬