Installing Grandstream UCMC100 from scratch with two extensions. No experience needed.
Пікірлер: 31
@peterjames37248 жыл бұрын
general info and 6102 discussion until 4:10 then 6104; extensions 7:42; sip trunk adding 14:20; check sip status 16:15; inbound/outbound routes 16:30; ivr / auto-attendant 20:40; ring group 24:50; fax sending 27:50
@fabianlazarte74659 жыл бұрын
Excellent tutorial, thanks! I will definitely consider your company when looking for SIP trunking.
@gogolinda72993 жыл бұрын
Excellent
@sultanbino9 жыл бұрын
thank you for clear demo 10/10
@alaabadri20087 жыл бұрын
Thanks for this Excellent tutorial , but i wonder if we can use ucm appliance as a gateway for Elastix server if not can we add some of Elastix server module like call center module to Grandstream ucm appliance
@gopu64107 жыл бұрын
clear demo very good
@rmontana36937 жыл бұрын
I tried Elastix and it was such a headache to set up, especially with various phones and I had lots of issues with dropped calls and mysterious intermittent problems. When I replaced the system with Avaya IP Office the customer loved it and the complaints stopped. Do I want to keep using Avaya? No, I would like to use something open source and something cheaper, but until there are alternatives that are as easy to setup and problem free as Avaya I am not going back to anything Asterisk.
@raptown20006 жыл бұрын
Great tutorial!
@iYousif_7 жыл бұрын
Does the UCM6100 series has a wallboard like Avaya systems? Thanks!
@attrib017 жыл бұрын
hey I have and question, I do have and UCM6104 and I connect 3 FXO lines and I have this problem with the inbound calls that I can only receive 2 at the same time and the Voip lines and the 3 analong line the system don't pickup those calls. Any help thanks you!
@ahmad-rateb7 жыл бұрын
thanks good one
@mohammedmadani12557 жыл бұрын
thanks bashar , but i have question about how can i restrict extinsion to commuincate some other extension ?
@nithingeorge5176 жыл бұрын
Hello, I am trying to import XML file on my Grandstream phone (GXP 1780) via the import setting under the Phonebook. The file gets imported and it says a message, "File imported successfully". However the phone doesn't read it, and i dont see any contacts under the Phonebook->Local Phonebook. Can you help me with this issue?
@moatazshawky54568 жыл бұрын
Dear kindly I need to know how to enhance the voice Quality, I configured UCM6104 with 3 GXP2110, GXP2120 everything is okay Inbound, Outbound calls but I've Noise Sound.
@edwardbaylon84029 жыл бұрын
Hi Sir, our company is planning to buy the UCM6100 series, but we would like to ask if auto-provisiong or the zero configuration also work with other ip phones like polycom or cisco. if not is it possible to add it manually? Both phones are SIP phones. Thanks.
@Khalis-sss9 жыл бұрын
+Edward Baylon Not possible, you can only add configure file to UCM storage and upload from there (so in some way you can provision).
@keajewelry8 жыл бұрын
i have a question can we set up paging extension to Extension with these device and how ?
@Shayma_a5 жыл бұрын
When I write the ip address of UCM in browser, it doesn't connect to the page of UCM!! What can I do?
@thusijeya95618 жыл бұрын
I have 6104 ucm,outgoing call is fine but I cant get incoming call from primary number ,iam using analog 3overline phone ,phone model is 2170gxp model.anyone know issue?
@alexanderslobodianiuk8 жыл бұрын
when I try to call I hear:"all circuits are busy now please try your call again later"....but when I call from outside everything is fine...(((
@razerbots8 жыл бұрын
Hi LucidPhone, I'm hoping you or anyone out here can help me out. My UCM6104 unit was previously managed by a colleague who has since left the company. She changed the username and password, and I'm unable to login now to change some settings. Do you know of anyway that I can gain access into the unit? or if I do a factory reset will the login id and password revert back to the default which is admin/admin? Regards.
@JeroenBuggenhoudt9 жыл бұрын
How to add a phone which is not a grandstream device?
@supersmart6717 жыл бұрын
Can I update an existing live system without losing existing configuration?
@milindtech Жыл бұрын
How to add GSM GATWAY
@macnasty76057 жыл бұрын
i have a 6102 but sees only 2 of the 5 devices.. very hard to configure.. not working :(
@LucidPhoneMississauga7 жыл бұрын
I suggest that you use LucidPhone UCL202 IP PBX instead. It is stable and has no issues.
@KorgKapperi7 жыл бұрын
I have the same (grandstream ucm 6102) and find it difficult, almost impossible to configure.. Your video shows hot to configure this device, why do you suggest to get rid of it ?
@hishamk7 жыл бұрын
Because it seems they've sold these devices to their customers in the past and had a ton of problems setting them up as well as reliability problems, which eventually led them to design their own solution using Asterisk (LucidPhone PBX). They're basically just trying to help people with these substandard products (Grandstream) to get them to at least work for a bit.