Great RC Plane Gasoline Engine | Stinger 15CC Gas - Petrol Engine (My first engine)

This is my first RC engine, it uses gasoline/petrol to run, which will save a lot in operation cost, no need for special fuel, it's really powerful and simple, 15cc is enough for a moderate size RC plane, with a 700cc fuel tank will hold enough fuel for 1-hour flight. The price is very competitive and this is only one of the models available from that online store.
As for every new engine, the break-in process has to be carried out to ensure the conditioning of the mechanical parts and get more life out of the engine, in this video I show all of that.
Engine bit.ly/3fvzeO9
(use the coupon "JoyplanesRC" for 15% off, valid until June 30th, 2021)
Join our Discord server: / discord
Website joyplanes.com/
Become one of us: goo.gl/zKQ706
Facebook / joyplanesrc
Instagram / joyplanes
More info about the engine.
This is a 2 stroke engine, 15CC and uses a Walbro carburetor, runs between 1500 to 15000 RPM, it can be fitted with a 13x6 or 15x6 2 blade propeler, the maximum output power is 2.4hp/1.76KW.
#JoyplanesRC #HobbyRC

[@xrae21]

This entire video is a classic "What NOT to do" unless you want to risk getting hurt or looking like a fool. Always anchor your test stand so that it doesn't have to be held down by your hands. Never stand to the side engine in the propeller damage path should it break. Never use a damaged wood propeller. Never run an engine for hours on a test stand. Set the high and low needles, pull it off the stand, mount it and break it in in the air. Never run it at the same rpm for more than a minute or two tops during break in. Everyone has to start somewhere but when I see beginners trying to give advice. I cringe because the majority of times it's bad advice and could get someone hurt.

[@Joyplanes]

Thank you for the advice!

[@knpjdad]

Thank you for saying all that that’s exactly what I was thinking too this is a how not to be safe video anybody that’s watching this please do not do what this guy is doing this is almost like a comedy skit but with very serious consequences

[@reignman0311]

Yup, 8:37 looking at that prop right below his arm where he was holding that test stand made me cringe,

[@praveensharma3456]

He’s going by the instruction manual

[@francotavella5496]

Bamoooooooosssss. Gracias joy estuve esperando esto hace mucho

[@lowtus7]

Best practice in my opinion is to use a cheap non synthetic oil for break in. High performance oil can hinder the break in as the rings may not bed in properly. It won't damage the engine, but may cause lower compression. You can buy a prop reamer to enlarge the prop hole, may be an idea, also balance your prop! Lol. Be careful and have fun.

[@mylesjarvis7571]

Dude I appreciate your effort here, but man this was painful to watch! Anchor that engine on a large stand so you don't need to hold it! I could see you panic when the engine first fired up. This is dangerous man, I definitely don't want to see you getting hurt but you're definitely asking for it!

[@Joyplanes]

Thanks!

[@UncleDuncan5092]

I think you did a good job with your first gas engine. Yes, the test stand should be more secure for your safety, but you survived. 👍🏼

[@effiongekpe3256]

I'm looking forward to this!

[@franciscorubio8290]

Congrats ,you did great, I been flying rc planes for 10 years , and I just got my r c g f 26 cc, and they work great

[@pcklee]

Thank you for posting. I find your video very informative. I intend to purchase my first gas engine soon and this video is really helpful!😃

[@wavetwo2171]

Hyped for this!

[@VideoJocky1]

I'm sure you are tired of hearing what you did wrong but here are a couple more. (1) check the spark plug Gap before installing into the engine. (2) Typically you need to measure the distance between the firewall and the face of the prop hub before drilling the holes for mounting the engine to the mount. This distance is usually part of the model documentation. If you don't, the prop may hit the cowling if there is one.

[@rickharms1]

Never drill out a propeller, it will not be centered. Use a reamer, available at most hobby shops or online.

Thanks for your video 👍 I bought an NGH GT9 Pro 9cc which is great too but smaller, perfect for a 40 size plane. The stinger should be perfect for a 60 size airplane. The stinger 15cc will be my next purchase. 😉🛩️

[@zubuxstein]

the vibrations is normal, it is recommended to break-in gas two strokes on the airframe so it absorbs the vibration. Like you did is ok because is shaking and that is what you want. Many destroy them during break-in mounting the on a solid engine stand. The engine will let you know when is past break-in, if transition is a little rough, and has only low and high, still needs some more runs. It will be spitting out excessive amount of black oil when new. Once the piston ring settles, engine will not spit out too much black oil. Keep the oil mix 25:1 to 32:1, do not go any leaner than that, will kill the engine. Some plug-in tachometers will not let the engine start.

[@ArobinNews]

Thank you for posting video ,,

[@MasboyRC]

Awesome, those engine looks so powerful 👍 I put the engine on the table and bolt on it to make test, its more safe and resist to vibration.

[@michaelyates4646]

That was awesome mate! Owning, running, learning the engine...that's what it's all about really. Now, go and grab yourself a four stroke glow engine and enjoy that!

[@calibermix8159]

enjoy a dirty engine ? glow is dying out. electric is the future

[@franciscorubio8290]

No man , glow fuel is so expensive like 30 dls gallon ,keep with the rcgf I’m switching to rcgf engines on my planes

[@fortcrafterbossbehold9027]

@@calibermix8159 A depressing future...

[@cosmorito961]

the engine is super handsome

[@yf222000]

Damn! Here I thought I was bad at some basic safety. He’d proved me wrong. 😮

[@TyK622]

Well done video ...... also you have a lot of patience. This will go along way to enjoying this hobby. I just bought a Saito FG-14C four stroke gasoline engine and have to go through the same process. But it is winter here in Ontario Canada so it will have to wait until next Spring. I will follow your steps on the engine mount and the Saito manual for breakin' Cheers and happy flying.

[@Joyplanes]

Good luck!

[@Jafaarmazin]

💐Thank you bro

[@-lolus-]

cool video . i got a chuckle while watching . to avoid complaints from neighbors , lets move to the park ... to annoy even more people XD

[@Joyplanes]

hahahaha

[@user-vd2sj2kf6t]

加油💪

[@TomislavReskovic]

nice vid but please switch fill/drain tube with the vent, because this way you have set up causes problems like you experienced, have to turn model upside down when filling and draining?? other way would be normal, when you fill/drain through nipple that is connected to a tube inside that goes to the bottom of the tank, and vent line goes to blank nipple in the tank, which brethes inside the top of the tank.... good luck

[@musicbuilder6612]

They have little rubber sticks to start the engine with use that

[@skyartrc8286]

Nice engine,you can also use a chicken stick to start the engine, it's just a small stick so the prop won't strike your hand or fingers, you can make one or buy them, I also like o.s and tiger brand rc motors, they are a little expensive but very reliable too.

[@Joyplanes]

Cool, thanks

[@01Duke390]

Thank you for this video. A very detailed and excellent showcase of this engine. Explained in detail each part. Thank you :)

[@vijayakumarkona443]

Sir in my openion please try to keep the engine in a predator drone type(i.e long wing glider type of planes) which looks dam cool sir I like it very much

[@MrAaa9271]

nice

[@randyleazenby2351]

I agree with the comment below. A freindly ama club would have been much help. No you do not have to break it in as long as you suggest.

[@franciscourena5636]

Great presentation Questions 1. What type of battery did you use for the servo that pulled the throttle? Voltage?

[@jesweet]

Lithium Polymer, from Turnigy I guess. The voltage is about 11.1VDC (3S; @3.7VDC)

[@erayyediler]

Do you have a new coupon?

[@short5stick]

That is all I use now is the stinger line.

[@personalonly3408]

Super I am from India

[@thetoono]

Me too

[@wk713]

I am also

[@parthpatil3723]

Semm

[@Thomas--Jaleby]

Me

[@anantyapa8115]

I have 15 cc os engine. By the way what is the maximum thrust of this engine.

[@albychainsaw80]

Where did you buy it?

[@frankyesjosh587]

Hi , what's the fuel , please ? sp98 or 95 for car with 2T oil ? Thanks for video

[@rizky_maison]

How many comparison beetwen oil n gas, 1000ml gas : 25ml oil?

[@thiagog.c2554]

Is it possible to mount the muffler with the outlet tube pointing downward?

[@reignman0311]

You can mount the muffler in any position suitable for the plane u are putting it in or they sell aftermarket mufflers..

[@septimusseverus252]

Like and sub ... Awsome video bro.

[@homienat3374]

Im sorry mate but that was not only dangerous, but brake in was wrong ,stick to the gliders mate,good luck ,try not to cut ya fingers off.

[@julienlabell73]

the music you put on the first watt is it thanks

[@julienlabell73]

yo

[@anantyapa8115]

How much noise it produces.

[@user-ji7pz2rb2b]

Купил себе NGH 9 cc . Не могу завести, даже не буркнет. Завожу пальцем, так как не стартера. Топливо сделал как по инструкции. В че может быть проблема? Есть не большой пузырик в шлангочке от бака до карбуратора, и он не в какую сторону не двигается, я думаю может быть движок не засасывает топливо ? Помогите!

[@taham6757]

i kinda need help for choosing my cessna 172 rc motor plz the wing span is 100 cm the body is 55 cm the wait with battery is 440g can any one help for choosing the best motor for that

[@darkiee69]

Anything in the 150-200W range will do just fine

[@sweateconomytoken]

How do you control the speed?

[@David-hm9ic]

He has a servo connected to the throttle on the carburetor which is operated by his transmitter. That's the normal method of controlling the speed.

[@mdmuntaharul6795]

What is the max thrust of the engine

[@prabukengg]

100 kilo

[@anishpatil3902]

What is thrust to weight ratio

[@Joyplanes]

I haven't tested that yet, but it will be about 3:1

[@Syed-zp5oi]

Hi if you want start with engine model first go with glow engine ....this cheep engines or not give good life ....best engine or OS DLE DA ....

[@nicov.2151]

nitro is old fashioned and not accepted in most rc clubs.... this is a good engine to start with.

[@tray22]

I only have glow engines and have a hard time finding fuel. I would say start with gas or electric amd stay away from glow.

[@prinzvongrorgenwugs7474]

A carburator from a chainsaw!

[@ganjalfthegreen5312]

Does sound like one

[@QuentinCarter1975]

Walbro carbs are the industry standard for 2S & 4S small engines. Bruscutters, Blowers, Saws all use them.

[@rickknowles9620]

I would not follow this persons precedure. Its dangerious not to have the motor jig anhored solidly and the gas tank was flopping around. Using the drill in this manor would definately damage the prop. There are much better videos on this topic.

[@bashkillszombies]

$240 is very expensive for such a small motor. Never look up RC engines, find small engines by looking for small engines, or "scooter motor" or something like that. Soon as you say RC the price goes up 10x.

[@yxhankun]

2 cycles engine

[@labangeneraux5608]

this is hard to watch seeing him quickly flick the prop with that carb closed

[@robertmartian4644]

Put it on a bicycle.

[@erfanmonemi8112]

Please be more CAREFUL

[@musicbuilder6612]

Get a bigger propller lol

[@TheVillegom]

Your tank is upside Down

[@quattro4468]

Only virgins fly electric only.

[@packer34]

Dude you need a better test stand you looking to lose a finger??

[@GENESUTUBE69]

Never have I seen so many mistakes in one video

[@calibermix8159]

what mistakes mister expert ?

[@franciscorubio8290]

So!he said it was his first time , come on ,he did great for first time!, can’t deny that!

[@christjanehusacek4911]

Nicht gut gar nicht gut 😢

[@MrZeek101]

I think you should have done a bit more research before posting this

[@billjones3071]

Glow engines are best for rc planes, gas suck also sounds like crap , stink, heavy , expensive,

[@fastbow9]

Qualified as the worst RC engine video on KZbin! Should be taken down to protect viewers!

[@josephacosta5631]

Clearly, you are new to attempting to start an R/C engine. Presenting this video in the way you did presents YOUR process as a dangerous behavior. Read the manual FIRST. SECOND, watch a PROFESSIONALLY prepared video with regard to the SAFETY, AND STANDARD PROTOCOLS , WITH RESPECT TO THIS HOBBY SPORT. YOU, are not prepared to provide a video of this type, and therefore pose a serious risk to yourself and anyone else who believes it's a simple process. DO NOT BRING ANYMORE ADVERSE POTENTIAL TO OUR SPORT. In the last few years to many " INEXPERIENCED EXPERTS, KZbinRS, AND " INFLUENCERS" HAVE DONE NOTHING MORE THAN TO DEGRADE OUR HOBBY/ SPORT" causing the hobby to undergo critical regulation as never before. I am a 50 year airplane/ heli competitor, judge, r/c flight instructor and professional drone pilot in the Aerospace industry. One must be a BEGINNER, before they assume enough knowledge to " INFLUENCE" others!!

[@pscparamesh3154]

WHAT THE STATUS OF THIS ENGINE NOW