Greenfield ride on deck repair

[@johnp1388]

Thanks mate, great video. Had my 18.5 / 32 throw the cutter belt yesterday (first time ever in it's 12 or so years) and I noticed the cutter deck v pulley is stiff as heck. Your video is of great help for me to begin a fault finding and repair process. Many thanks again 👍👍

[@leifmorris5114]

Thanks you. Very helpful,top quality teaching

[@RobertHughes-hh9zg]

thanks mate helped me out fixing one for nextdoor ....

[@harryatkinson445]

Thanks for the advice Saved a lot of of problems

[@magnusbjorklund7999]

Hi Heff thanks for getting back to me. I purchased a good looking mower jack from Total tools. A Renegade. sorry it took so long to get back to you.🙏

[@jakobshanks3510]

This was very helpful. Especially the tip about left-hand threads. they always trick me.

[@martyjohnston700]

Thanks for the video, the left-hand thread is very helpful. Only thing i can recommend is not hitting the bearing with a hammer like that, will cause tiny divots in the bearing race and decrease bearing life. Use the old bearing outer race ontop of the new bearing to hammer in. Also to much grease is bad as it will expand with heat and pop the seal. Deck levelling video would be great for a future video. Thx mate.

[@CrRodney1]

Yes me too. The deck seems to be raised at the front. Difficult to engage the blades. Mine is a 21 34

[@malypetu1409]

Good video, thanks. I've got a Greenfield MiniMow 25 that the engine explodes (literally), and I need a new engine (or, better, a good second-hand one) for it, can you recommend a good place to get one?

[@johnp1388]

Good video mate 👍👍

[@magnusbjorklund7999]

Yeah thanks mate blew a hole in my deck. Where do you get the little mower jack from please? Need one of those to work on my Greenfield and replace the deck.

[@heffsshed9542]

I think I got it from super cheap years ago can’t quite remember. Best thing but

[@stevencrook2514]

What size belt mate? I need one for my deck but cant see any details on the Greenfield manual.

[@heffsshed9542]

@@stevencrook2514 oh mate nite sure now don’t have mower

[@TerryMoore-v7e]

Good video ! I have a problem - broken tie rod on steering link on steering chain end. I replaced one on the other end of the steering link and all was well for about 5 minutes of mowing, then this tie rod shattered. Do you have a video on how to repair this. Thank you!

[@heffsshed9542]

Hi mate not yet

[@billcohen9053]

Hey mate. What are the bearing part numbers? In the middle of rebuilding 2 decks. Your videos have been extremely helpful

[@billcohen9053]

Or at least bearing sizes so I can walk in and know what I am asking for. 32 and 34 inch decks I am rebuilding

[@heffsshed9542]

6204 I think

[@damohart6909]

Hey mate great vid, but is there a trick to getting the pulley off the spindle?

[@heffsshed9542]

?? Which pulley

[@danielandrews7329]

Keen to know as well, the main spindle shaft pulley.

[@MickB52s]

@@danielandrews7329 pulley

[@kravmandan5733]

Thanks

[@damohart6909]

The cutter one, but it’s ok we worked it out. It had been twisted so that the key had stretched the slot and edged itself in an awkward way

[@heffsshed9542]

Oh awesome sorry for the late reply

[@Thepigfromthepot]

No flys on the old greenfield

[@martyjohnston700]

Love mine, a worthy investment. Only thing I don't like is the deck digging in on one side if turning too fast, have to slow down for tight turns. Be nice if the deck wheels were spring loaded swivel wheels instead of static wheels. Buffalo lawn on rough ground.

[@channelhismojo7192]

These mowers are now Chinese garbage. Two spindle bearings gone in 10 hours on mine. Never again.