GTHaus Musa Meisterschaft Exhaust Install Part 2 - The Exhaust Hardware // Lexus IS500

[@dk3fiddy]

Meisterschaft FTW! 🏁 That open valve cold start was 🔥🔥🔥! OAN, I can really appreciate the time you took to run the vacuum lines properly! Looks very clean! ✊🏿

[@specONE]

Appreciate the love

[@SoleDreamzAndLexoticj]

that thing sounds so mean... thanks for the video

[@specONE]

it sure does sound mean!

[@nameless7584]

Sounds nice , good luck with the smog check though :D

[@EvoSteve89]

don't live in a commie state lmao

[@DakotaOgnenovski]

Where did you mount the black box and get power from? Thanks

[@specONE]

My way was complicated, I recommend going to the cigarette lighter port so it will only work with the car on and won't drain your system. I believe I show where I mounted the box in a different video

[@GoldySingh-xv6lv]

Did you unplug the O2 sensor before unscrewing it? I tried to, but the wires start twisting and I'm afraid of breaking them

[@specONE]

I did not unplug the o2 sensor before unscrewing it. I let it twist and make sure to twist it about the same amount when installing it onto the new midpipe.

[@renatoshehu7902]

Did you use the same gaskets and the hardware from the stock one or do they come with the gthouse order?

[@specONE]

I reused gaskets. GThaus didn't provide any

[@XavZero333]

When you purchased your exhaust system did it come with the mid-pipe or was that sold additional? Also any dash codes pop up?

[@specONE]

Purchased separately as an addition. No dash code if o2 sensor is installed and gaskets don't leak

[@StarManProduction]

What adapters do you have for the jack stands thays on the pinch weld?

[@specONE]

To be honest, I don't remember where I got them from at this point. But they don't really work too well for the pinch weld. The pinch weld just cuts the part it rest on in half

[@oakleydepiction]

Hi Rodney. I'm considering getting this exhaust, but I don't want any drone. Is that an issue you have experienced?

[@specONE]

no drone to me even with valves open on the freeway

[@oakleydepiction]

@@specONE nice

[@Luis-pd5be]

Any worries with carb compliance? Only reason is I've been looking at this exhaust and I'm in CA lol any input is appreciated!

[@specONE]

🫣

[@Krisskross_]

Is that socket size is 7/8 for O2 sensor? I went to the muffler shop and they don’t have that specific size. That’s why i ending up going home sad because they didn’t install my exhaust.

[@Krisskross_]

And do you have any link for alittle bit cheap socket like you can recommend? Thankyou

[@specONE]

That's disappointing a muffler shop didn't have the correct o2 sensor removal tool. It's a standard Toyota size. Here's example of one: ARES 70039-3/8-Inch Drive by 7/8-Inch (22mm) Offset Oxygen Sensor Socket amzn.to/3VTEflm

[@Krisskross_]

He has one tool to remove the O2 sensor but he wants to cut the hitshiled for O2 sensor and told him not to do it like that. Thankyou so much for the link! Help me a lot!

[@Litoflow]

@@specONEthis socket falls short. Doesn’t reach. DO NOT BUY.

[@edcain9492]

If U it's a Calif O2 Sensor,Diff.from Stk.May have to get it f from Dealer Parts.I had a 2001Tundra Calif.Sensor Truck,Bitch to Remove.

[@Stevenmashup]

Any check engine light?

[@specONE]

No check engine lights!

[@MRSKY60]

I’ve been thinking of getting the gthaus for my is500 How is it

[@specONE]

It sounds amazing

[@MRSKY60]

Did you get it tuned ??

[@specONE]

No tune, just stock ECU mapping

[@Xxgamer712-69]

It sound like a ford gt

[@luckynewjersey]

Can you sell me your stock exhaust?

[@specONE]

Sorry I have no plans of selling the stock muffler system.

[@luisreyez9876]

How is It with cops ? Being in gaylafornia ?