Control Techniques C200 VFD local control, parameter set up, Factory reset, single phase (English)

[@majiburrahmankhan4103]

Thanks sir

[@lewidris]

Hey my friend, great content, I have set parameters on my motor, in using a 18.5 kw tec motor, I’m confused on the part where you enable the the drive? With the blue wires

[@lewidris]

Sorry I have little knowledge on these things but What sort of wiring do I need for the drive enable? Is the a certain requirement? Any help would be appreciated

[@samuelahiafor]

Cool

[@shrikantkotame1179]

I have the error OI AC could you plz for this

[@TheBlaxxxblaxxx]

Hello, I've been set few parameter however it cant be saved and change to default value when I turn the vfd off. Do yo know how to solve it? Any help will be apreciated.thank you.

[@thanoskalimeris4791]

If the power supply drops and you start the invert it starts with 25HZ while the selection is 50HZ what am I doing wrong?

[@IGSElectronics]

Hello Fellow colleagues. If you enjoy the video please click that like button and if you did not, dislike it and let us know in comments, what was, that made you not happy with the content, so I can learn from it and make better videos for you in the future. Have a great day everyone.

[@crlist1453]

I have an older Control Techniques SE 2D200150 SE2.5M/TL 1.5 KW. The readout shows Fr-60.0 but no output. Would this indicate a configuration or wiring problem or a failure? I got this with an equipment purchase. and do not know if it works. Thanks -JD

[@IGSElectronics]

HI JD. When you start the drive is it ramping up?

[@andrei.a6831]

I have an error Er.01.AC. how can i solve this and what is that mean? I'm trying to start a motor with specifications:2.2 kw, 165v, 12.5 A, 17000 rpm. Help please

[@pendopolimas199]

How to program brake function..?

[@IGSElectronics]

All brake parameters start form parameter 46 page 49 in control user guide. To get more explanation what each parameter mean, refer to Parameter Reference Guide on Control Techniques website, link provided in description. I don't know your application so i wont be able to help much anymore, but all the info you need will be in manuals in parameters I have mentioned.

[@juancamacho4841]

I hace this alarma Er 0 1AC what can l do by reset??

[@juancamacho4841]

What can l do for reset alarm

[@HassanSahm1]

I have an error OU and Er.01.E1 How can i reset the fault And what does it mean by those errors plz

[@lewidris]

Sorry I have solved my issue, but I need to run the motor in reverse I did a steps above but 24v into port 13 and did the auto tune, but it’s still not in reverse, any advice?

[@IGSElectronics]

If you have a drive from the new, everything should be as the diagrams suggest. Remember inputs can be reconfigured, so if that has been done and not by you, then the best would be to default the drive and check then.

[@thuitamaina5488]

yes enable keypad reference

[@lewidris]

@@thuitamaina5488when I load my induction motor which is being controlled by the c200, I keep getting phase loss, wirings all good, 3phase is good, not sure why it keeps cutting off, any advice?

[@anilyeduv9366]

Solo speed kaise karte hain motor ko

[@HassanSahm1]

Does it a must to do autotuning ?

[@IGSElectronics]

Hi There. No its not. Its optional and by autorunning you make drive performed better with the motor.

[@VijayRealm]

I have an error ER.1E.Ac how can I reset this fault and what does it mean by those error plz

[@norbertoperez6511]

It means jigh amperage, you need to assure thta your motor is in good condition, neasure the insulation of the motor and the cable and see if the motor is not grounding, before operate again in the case it will show ypu the alarm again

[@usefultips8755]

Program mode not coming

[@thiensuutv1286]

i want clear password parameter setting ?

[@josefinaiipolicarpio6647]

how to remove the security code

[@IGSElectronics]

You should be able to do that by resetting the drive, if that don't work then the only thing i would think is left is to connect it to laptop and do it vi there software.

[@VirendrasinghVirusingh-nx2lh]

Frequency unlock parameters nomber { }

[@juancamacho4841]

Alarm E r 0 l A C please help mi