My vacuum line was clogged, saw this video took about 10 minutes but the line is cleared thank you for posting this video. Followed exact instructions and it worked.
@YummayInMyTummayy2 жыл бұрын
This video saved me! Thank you! What I ended up doing, since I didn't have anyone to help, was flow through the pump first then flow through the skimmer. I could clearly see, from me standing at the skimmer, when it was unclogged because the pump started to bubble. Tip for all the single people out there!
@Redkinkid198510 ай бұрын
Yummy indeed
@anthonymotola42632 жыл бұрын
Great video, finally learned how this filter set up works in a straight forward well made demonstration .
@user-iz9ix8ru8d2 жыл бұрын
Thank you so much for your videos! As a first time home owner with an old pool, your guides have been lifesavers!
@mariabrigham73412 ай бұрын
Thank you Mark for great, easy to follow advice. I'm going to try it.
@poepoeshasha3 жыл бұрын
I’ve learned so many things on your channel ☺️Thank you a lot!!
@myklconjuay36373 жыл бұрын
Hey, thanks. I just replaced both Motor and housing after avoiding it for eight months; after 25 years the housing had cracked. (It only lasted a quarter century - I'm complaining to Hayward!) Anyway I have never seen a vacuum plate until this video. Must get one! I also have a clogged drain so the fight isn't over yet... Thanks for GOOD information!
@marshag80752 жыл бұрын
Terrific advice and immensely helpful! Thanks so much!!!
@nextstepcmh65187 ай бұрын
March 2024 just tried it on a clogged vacuum line, worked like a charm. Saved me from calling a pool repair company 👍🏿
@gloriaruiz3827 Жыл бұрын
OMG! All hope was lost until I found your video!! Thank you!! The rag method worked like a charm!!
@TimMcMahon-d3w Жыл бұрын
Thanks so much for the advice. It worked a treat on a blockage in my main drain that had been stuck fast for months. Much appreciated..
@brians.44884 ай бұрын
A two skimmer pool u could borrow the suction from one skimmer and use that suction at the clogged skimmer. Set filter to rec. Let the pump get to full prime by leaving the pool hose end just out of the skimmer hole and when full primed stick it in and suck it out with a little luck it will go down the other skimmer pipe.
@thewaddy3 жыл бұрын
Excellent advice. From Spain.
@joaosennaification Жыл бұрын
Unclogged the vacuum pipe with this method..thank you so much!! 😊😊
@Frankybeanselevators Жыл бұрын
It worked for me, after a couple of tries with the hose and rag a large clump worked its way out!!
@solimandina2 жыл бұрын
I’m about to try this method, thanks for all your advice, your videos are lifesavers!
@jessicavillalona22192 жыл бұрын
This works!!!! Thank you so much! Getting a vacuum plate today!
@Nothereneverwas692 жыл бұрын
Ha , I watched a KZbin video and it showed me how to vacuum my pool incorrectly and I clogged my skimmer line , then I watched this you tube video to fix it , worked like a charm
@kennyg57219 күн бұрын
WOOOOW REALLY NICE EXPLANATION
@marlonsilva3055 Жыл бұрын
Thank You. You are the best. I'll keep you in mind when I need help for my pool
@CincyMech2 жыл бұрын
Going to try this method to identify my skimmer and drain lines. New pool owner here.
@silviagarza76126 ай бұрын
Ten secs in you helped me with my issue. My plumbing was leaking water.
@maryhenley6755 Жыл бұрын
Thank you Mark you explain everything perfectly
@robertkelsall17412 жыл бұрын
What an excellent video. So well explained.
@chipperknick0103 жыл бұрын
My pump attempts to prime but only gets about 90%. I was thinking it was the typical O-ring on my pump but I’ve ruled that out. Guess it’s time to consider that there may be a leak. I’ll try this out and let you know. Great idea with the hose though!!! Brilliant
@chipperknick0102 жыл бұрын
Turns out… it was the O ring around my pool filter!! Super small leak there but all is fixed. Thank you again sir
@wz3y2 жыл бұрын
Thank you so much for this video. After watch this, I felt that my intelligence level went up a level.
@dougsmith5195 Жыл бұрын
THANK YOU!!!!! Blew the crap I had vacuumed like an idiot out of the pipe and I am back in business!
@markghose68753 ай бұрын
Excellent video
@normajeanbegley48892 жыл бұрын
I just either use my blower, or my pressure tester set-up, I will try this in the future thanks !!
@ceecee7237 Жыл бұрын
This made total sense, but I would caution to check valves first. We had pool work done this week and afterwards we saw that the skimmer wasn't sucking in water. Everything else worked great. I came here to find a solution, but didn't think there was a clog, so I called the gentleman who did my work and asked if it could be a valve. Sure enough, my valve was set 100% to the leaf trapper instead of in the middle between the trapper and skimmer.
@brianbembry8171 Жыл бұрын
Pool professionals use c02 tank to blowout suction lines
@luciesheppard6760 Жыл бұрын
Thank-you!!!!!!!!!!!!!!! This worked and it was so easy.
@indianna3132 жыл бұрын
EXCELLENT 1. Blow hose water FROM pump to skimmer (other people's video have you blowing from skimmer which just reinforces the blockage) 2. Crimp hose off and on to get a pulsing action (great suggestion) 3. If still blocked, use the pump to pump water INTO the pump's suction line (much more powerful than a hose, and yes, you will need to cut your pipes and get a length of flexible pool pipe). A lot better than digging up your yard to get down to underground pipes and locate/cut out blocked section 4. Great practical advice
@poolleakacademy55732 жыл бұрын
I unclog skimmers for a living. I always have a small bright colored piece of cloth or tape I first try to force through the pipe. If it travels freely then there is no clog. sometimes it acts as a plunger against porous pine needles. I always use air from a 20 gallon air compressor, I blast it slow at first then I work it up to full blast. To add the air in the line, I tap the pipe with a 7/16" drill and a 1/4" -18 npt thread - this fits the threads of most air connects.
@ApartmentMaintenance2 жыл бұрын
Can you explain the bright colored piece of cloth or tape that you use to see if it travels freely? Thanks 👍
@robinsevio8385 Жыл бұрын
Thankyou for your free advises.🙏🙏🇻🇺
@kelm11233 жыл бұрын
Very good video, learned a few things along the way.
@ahmedjalal31993 жыл бұрын
Thank you so much for the instructions
@garyhammond21032 жыл бұрын
that worked perfect, blew debris outta the line with the hose trick
@jamespopp6324 Жыл бұрын
very helpful video. thank you
@rdkingjaxfla1423 Жыл бұрын
Excellent video…thanks for the info 😎
@Brandon4EK6 ай бұрын
Had no idea you weren't supposed to connect the vacuum hose directly to the skimmer... I asked several people and none of them mentioned that, but it always struck me as odd- why would you want all the leaves and debris getting *in* to your system? Kinda defeats the point of a skimmer basket if you're just going to vacuum crap directly into it lol I'll try this method to de-clog and report back, thanks for the info.
@racebiketuner Жыл бұрын
Great stuff! Thanks a lot.
@bonnieravey73882 жыл бұрын
Well being the Maintenance Director of all things home. I listened to your video and tried as many of things you suggested. Found out we didn't have either a skimmer or drain shut off. Well then let's just see if we can push the discharge out the skimmer feed with your towel method. Well one 10 gallon pail full of sand later I quit altogether and got a shut off for the drain side. I then pushed the hose and squeezed it for two days to get all the rest of the sand out of the skimmer and lines and still nothing. No suction. Sitting literally pis....d on the chair I had in the pump house I reached down and touched the chlorine dispenser we never use and low and behold it was loose and shouldn't have been. Took it apart added pucks and regained full pressure. How it got lose I can't figure out. It will be the first thing I check the next time if ever we have a loss of pressure.
@spicymcbeal50073 жыл бұрын
Thank you so much. Solved my problem exactly! 😎
@brentmcdaniel33422 жыл бұрын
Great video, this worked for me
@ebriere71642 жыл бұрын
Hot damn, this worked. Thank you so much for the I instructional video.
@paulbuschman83183 ай бұрын
Seems like a great technique to try, but what if your system doesn't have a shut-off valve on the drain line?
@HallmarkPoolSupplies3 ай бұрын
@@paulbuschman8318 It would be nice to have a valve on both the skimmer line and the drain line, not only for this situation but it will also allow you to regulate the suction on each line, especially when you vacuum. Thanks for watching.
@Artseventy63 жыл бұрын
I have a question about the main drain, for a couple seasons now if I switcn the valve to draw from only the main drain or even to draw from both the skimmer and the main drain, the pump loses suction, then it will build back up, then lose it again, I normally just leave it on the skimmer because of this, could there be something blocking the main drain? Should I try your method to clear it?
@HallmarkPoolSupplies3 жыл бұрын
This would be better to troubleshoot over the phone, give me a call. I’m in the office Monday-Saturday 10 to 5 EST.
@mattc.3102 жыл бұрын
I have a square skimmer basket and have not found a square vacuum plate anywhere. Probably have to use a filter can between the vacuum and the skimmer.
@ERSLIFE-we1mg Жыл бұрын
thank you 🙏🏽
@myfurrykid3 жыл бұрын
Our swimming pool has a solid custom cover and it gets closed after we use it, it was vacuum yesterday because there was some diatomaceous earth on the bottom by the skimmer, today I noticedt the deck skimmer didn't suction the chlorine treatment, could it clog even when there's no debris going on either skimmer? We added 4 pounds of diatomaceous earth 3 days ago. And if you don't mind, is your business in Southern California, close to Riverside, please? Thank you for the excellent videos.
@desertcamel3573 Жыл бұрын
Great video
@PamWebb604 Жыл бұрын
Our in ground pool has two skimmers and only one isn’t drawing in debris. Do I plug the working skimmer when I try the hose method? Thank you, great video.
@HallmarkPoolSupplies Жыл бұрын
You would turn off your drain and the skimmer that is working. Leave the skimmer in question open so you can run the water through and unclog. By closing the other lines you will be able to put all the pressure on the skimmer that is clogged. Good luck and thanks for watching.
@PamWebb604 Жыл бұрын
@@HallmarkPoolSupplies thank you but we only have one skimmer line to close off.
@desmondedet49632 жыл бұрын
Nice idea
@martinduggan40773 жыл бұрын
come to Spain the plumbers who build the pool use flexipipe and the pipe collapses. I normally replace it with 50mm rigid pressure pipe
@tangotommi Жыл бұрын
Also, one more thing, a recommendation for a good skimmer sock. I’ve have good ones that can be backflushed and cleaned. The ones I got this time are not good since they plug quickly and suck the float down and then it can’t skim! The mesh is Too fine. HELP! Thanks!
@HallmarkPoolSupplies Жыл бұрын
I believe that what you are referring to is a filter saver which is used on your skimmer basket. This does work well but you will have to clean on a regular basis, if not it will get clogged and restrict flow. Thanks for watching.
@tangotommi Жыл бұрын
Yeah, I just call them skimmer socks but I clean them usually once a day but they do the job. Here in Memphis get lots of pollen and there’s my neighbors pine trees so they’re a life saver. I’ll just try a different brand. Thanks!
@verachuckdave5 ай бұрын
Would this work for my spa suction line ? Pool pump is pulling zero water from spa!
@HallmarkPoolSupplies5 ай бұрын
Yes, just make sure that you run the water from the pump side towards the spa. Thanks for watching.
@gm39233 жыл бұрын
If the hose alone didn’t clear. Could you use a snake from skimmer end to loosen the clog?
@HallmarkPoolSupplies3 жыл бұрын
You could give that a shot.
@sarahaaron50652 жыл бұрын
'+
@LetsDIYIt Жыл бұрын
The skimmer that is closer toy equipment has much worse suction, so I suspect a partial clog. I bought a bladder but I realized I have the soft PVC pipe for my lines so I didn't end up using it. Would you suggest I go with your method rather than the bladder? Afraid it builds too much pressure. Not sure if it really creates more pressure than this hose/rag method
@HallmarkPoolSupplies Жыл бұрын
Both have the same garden hose pressure. You can do either method, good luck. Thanks for watching.
@AndrewFagan-b4l Жыл бұрын
show how to unclog with a cartride filter as well please
@HallmarkPoolSupplies Жыл бұрын
You would unclog the skimmer the same way. Thanks for watching.
@julietsteyn11129 ай бұрын
Kreepy krauly stopped working. Could a blocked skimmer be a possible cause?
@HallmarkPoolSupplies9 ай бұрын
Yes, however it could be several other things such as a broke or clogged unit or even a clogged pump. Thanks for watching.
@kevinrothe5937 Жыл бұрын
Does this work with the main drain too?
@HallmarkPoolSupplies Жыл бұрын
Yes, however the main drain does not usually get clogged unless the grate is missing. Thanks for watching.
@slipnorris5882 Жыл бұрын
Could it be clogged even after I felt a decent water pressure out of the skimmer hole, I constantly have low suction. My drain valve is frozen. I'm not sure if it's open or closed, I jump in the pool to test drain suction, but the water is too cold.
@HallmarkPoolSupplies Жыл бұрын
If the skimmer is not clogged, you may want to clean or backwash the filter. If this does not change the performance you may need to check the impeller on your pump, if its clogged this could be the problem. Here is a link to a video that may help. kzbin.info/www/bejne/fXWViHeLlLt9pZI
@betsyeaster77722 жыл бұрын
Swimming pool happy
@xenofontosy Жыл бұрын
What about if a skimmer and drain is on one pipe ? Do we have to open both?
@HallmarkPoolSupplies Жыл бұрын
The drain line and skimmer line should be separate. Try turning off the drain line first, if not you may need to cut the plumbing .
@xenofontosy Жыл бұрын
Mr Mark..I did that before a couple of months and it worked. I have done this again now because i had same issue and didnt work. I brought a professional and told me that something maybe stucked in the pipe of the skimmer. And told me thatbwe have to break the wall and put some new pipes. Is it possible something to got stucked? Do we have any 2nd option?
@HallmarkPoolSupplies Жыл бұрын
You may have to cut the plumbing and try the hose again or use a snake. You can also use your pool pump off the waste line, but you will have to do some plumbing.
@xenofontosy Жыл бұрын
@@HallmarkPoolSupplies do you recommend robot cleaners? If a buy a robot cleaner actually replaces the manual cleaning? Thanks
@HallmarkPoolSupplies Жыл бұрын
@@xenofontosy Yes, robotic cleaners work well. I like Dolphin robotic cleaners by Maytronics. Maytronics makes a lot of different models, so if you are interested in getting one let me know and I will be glad to help.
@xenofontosy Жыл бұрын
@@HallmarkPoolSupplies do they have the products in Cyprus?
@HallmarkPoolSupplies Жыл бұрын
@@xenofontosy Maytronics is an international company and is sold in many different countries around the world.
@frankiesacks2603 жыл бұрын
Can this be used while the pool water level is high or does the pool water have to be lower than the skimmer? I got the skimmer basket net sucked up and it didn’t make it to the pump basket. I still have pump pressure, but I can tell that the net is in there.
@HallmarkPoolSupplies3 жыл бұрын
It makes no difference on the water level. You are trying to push it out with the water pressure from the garden hose.
@samaraluper24362 жыл бұрын
How do I figure out which one is the skimmer and the drain? One of my lines is clogged
@HallmarkPoolSupplies2 жыл бұрын
Turn off your pool, leave one valve open and one valve closed, if you can run water through the line easily with no back pressure then that would be the drain line. If you switch the valves and you can’t run water through the line easily that line might be your skimmer line. Have someone check the skimmer when you do this, if they see little or no flow at the skimmer then you know that the skimmer is clogged. Feel free to contact me if you have any questions I will be glad to help.
@billakers6082 Жыл бұрын
I have one outlet in my attached jacuzzi with very low flow. Would this procedure help?
@HallmarkPoolSupplies Жыл бұрын
It depends on how your lines are plumbed, and if you have a clog in your suction line.
@billakers6082 Жыл бұрын
@@HallmarkPoolSupplies That outlet seems to work fine with the blower on but returns to low flow when blower turned off.
@HallmarkPoolSupplies Жыл бұрын
@@billakers6082 Do you have an independent blower? If so, blowers only blow air into the spa through small air lines. This has nothing to do with the pump. Do you have air induction for the jets in the spa? Do you have a dual speed pump?
@billakers6082 Жыл бұрын
@@HallmarkPoolSupplies independent blower, one speed pentair and no jet air inlet. I assumed the siphon air came from blower when off. Pool recently went through resurfacing and water line tile. Didn't correct the problem. Water jets out just no bubbles.
@HallmarkPoolSupplies Жыл бұрын
@@billakers6082 If you have a sand filter you can run on recirculate, if pressure is good then you may need to backwash. If the flow is still weak, you may need to check your pump and see if the impeller is clogged.
@rajcurry66962 жыл бұрын
Mark, what if I have a rock in the line? It’s just big enough that I can’t pull it back up from the skimmer side and won’t go through to the filter side. I have tried the hose method, snaking the line and even hydro flushing. Do you have any recommendations? Thank You 🙏🏽
@HallmarkPoolSupplies2 жыл бұрын
You may have to have a plumber professionally snake it out or cut the plumbing to remove it.
@misslucille28872 жыл бұрын
Thank you for the video. QUESTION? My pump will not prime from the skimmer side. We thought we had a leak but it was pressure tested and held pressure. It appears we have have a possible clog. However, we hooked up our shop vac from the pump side and blew air through the line and it blew through to the skimmer end. So it appeared to not be clogged but yet the pump will still won’t prime. We know it’s not the pump because we have hooked up and above ground temporary line and it works fine. We will still try your method with the hose but still stumped the airflow we get at the skimmer end if we do indeed have a clog. Any thoughts ?
@HallmarkPoolSupplies2 жыл бұрын
When running air through a line that is clogged with a shop vac the air usually blows air around the clog, using water pressure is always better. If you have any questions feel free to contact me I will be glad to help.
@misslucille28872 жыл бұрын
@@HallmarkPoolSupplies thank you for your reply. Going to try your suggestion tonight.
@misslucille28872 жыл бұрын
@@HallmarkPoolSupplies your thoughts??? We worked on the skimmer line for several hours last night. Starting with your hose and rag suggestion. We ended up hooking up a hose from the waste to the skimmer line to use the pump to try and push the debris back out the skimmer box. We did this numerous times alternating back to hooking the pump back up to try and loosen the blockage up. As we were doing this we could see improvement in the pump suction. The end result is the pump is working again and we’ll, but… no evidence of the blockage ever surfaced. We got minimal flecks of leaves and debris out here and there and that’s it. We are pleased the pump is working again, but unsettled with the outcome. Any thoughts or suggestions?
@HallmarkPoolSupplies2 жыл бұрын
@@misslucille2887 Hopefully you got it, there is still a chance that the line could still have some more debris or that the pump's impeller could be a little clogged.If you have any more issues feel free to contact me.
@HersheyBrown862 жыл бұрын
I only have one drain from my skimmer that goes directly to my filter then it goes through my Chlorine thing then goes back into the pool. So what I do
@HallmarkPoolSupplies2 жыл бұрын
You would run the hose through the pump in the direction back to the skimmer. If you have any questions feel free to contact me I will be glad to help.
@MK-uz9tz2 жыл бұрын
We used a drain bladder to unclog the skimmer. Now the clog is still there and the bladder is stuck in the pipe. The hose is still connected to the bladder. I am not able to pull it out. What should I do?
@HallmarkPoolSupplies2 жыл бұрын
You may have to loosen the bladder and remove the hose to get it out.
@karenpowell74252 жыл бұрын
How do you identify which is the drain and which is the skimmer ?
@HallmarkPoolSupplies2 жыл бұрын
You need to close one line and keep the other open. Then check the skimmer and see if water is pulling into that line.
@tylereves49252 жыл бұрын
How would this work if you suspect the clog is from the main drain and not the skimmer ?
@HallmarkPoolSupplies2 жыл бұрын
You would do the same thing, except with the drain line. However drains are grated, and usually do not get clogged.
@tylereves49252 жыл бұрын
@@HallmarkPoolSupplies thanks for the response. My main drain (at the bottom of the pool) has zero suction. I will try this out. Any other ideas on what the issue may be?
@HallmarkPoolSupplies2 жыл бұрын
@@tylereves4925 First verify that the line in question is the drain and not the skimmer, you may want to check your valves and make sure they are working properly (opening and closing). If both lines are restricted then you may have a clogged impeller in your pump. If you have any questions feel free to contact me I will be glad to help.
@AnthonyLeeBand2 жыл бұрын
I’m confused, what’s a skimmer lol
@zulissani92163 жыл бұрын
when u vacuum what function should be used water or filter
@HallmarkPoolSupplies3 жыл бұрын
You vacuum your pool, normally, in the filter position.
@dejansimic46203 жыл бұрын
good day i have one question? i have a pool 7,5x4,80 I am interested in the filter how many kilograms of sand and what pump power in advance thanks for the answer
@HallmarkPoolSupplies3 жыл бұрын
Do you have an above ground pool or inground pool?
@dejansimic46203 жыл бұрын
@@HallmarkPoolSupplies above ground
@HallmarkPoolSupplies3 жыл бұрын
I would recommend a 45 kilogram sand filter with a 1 hp pump.
@dejansimic46203 жыл бұрын
@@HallmarkPoolSupplies tnx😉
@squacher2 жыл бұрын
In a 100 years nobody ever thought to put in long sweeps when installing pool plumbing? Unbelievable!
@paulrooster21083 жыл бұрын
Oh boy - ok here's my issue In Ground Pool , It was installed back in the late 80's, I'm not getting any suction on my bottom drain , The skimmer has 2 ports in the bottom. (1) I know goes to the inlet of the pump , an the second port I'm guessing goes to the drain in bottom of pool. There's a pvc cover over the 2 ports in the bottom of the skimmer , Inside this pvc cover is a Butterfly Valve ( like a carburetor on a car ) an it has a lil T handle sticking out the side of it , I guess that would be to allow more suction on the main drain in bottom - or more suction at Skimmer to pump / or sorta split the difference to draw water from both . I tried running a plumber snake down to the main drain an yes I pulled up a bunch of stuff , so now I'm getting a lil bit of suction thru the main drain at bottom but obviously not enough . I took a plastic frisbee an pushed it down over top of the bottom drain an the pump suction just barely keeps the frisbee over top of the drain I can easily push it off with the pool pole . Any suggestions on how I could possibly increase the suction from the main drain to the pump inlet ( I have only 1 pipe coming up outta the ground going into pump inlet ) On the Filter outlet side I have pipes going into the ground with a gantry valve in between them that has 3 positions on it , if I turn the handle on the gantry Valve in one direction it operates a water feature at the low end of the pool running 3 jets that shoot water an air bubbles ( I know just enough about this thing to get myself in trouble lol ) , Thank You
@HallmarkPoolSupplies3 жыл бұрын
Drain lines and skimmer lines are not usually tied together but in your case they are. There is quite a bit to discuss on this so if you would like to call me, I can go in greater detail with you. I’m available Tuesday-Saturday.
@paulrooster21083 жыл бұрын
@@HallmarkPoolSupplies , thank you
@harleyinred13 күн бұрын
How do i keep water from coming out with skimmer open?
@HallmarkPoolSupplies13 күн бұрын
@@harleyinred If you have a valve you can close the skimmer or you can plug the skimmer with a 1 1/2” threaded plug. If you are trying to repair the skimmer then you can lower the water level below the skimmer. Thanks for watching.
@harleyinred13 күн бұрын
@@HallmarkPoolSupplies i thought i had a clog, but my skimmer has a crack at the bottom 2inch outside, tomorrow may try to temp repair but think new skimmer right?
@harleyinred13 күн бұрын
@@HallmarkPoolSupplies filter building up pressure and water does come up good when turn it off
@HallmarkPoolSupplies13 күн бұрын
@@harleyinred Do you have an above ground pool or in ground?
@harleyinred13 күн бұрын
@@HallmarkPoolSupplies above 15' x 30' oval
@Robert_H_Diver2 жыл бұрын
Would this work for the main drain as well?
@HallmarkPoolSupplies2 жыл бұрын
Yes, however the main drain normally does not get clogged.
@Robert_H_Diver2 жыл бұрын
@@HallmarkPoolSupplies what about if there was no cover on a pool for a year or so and the bottom is covered in sludge and leaves and pine straw?
@HallmarkPoolSupplies2 жыл бұрын
If the pool is that dirty, then you would need to vacuum on waste. When you vacuum on waste you will need to add water to the pool.
@Robert_H_Diver2 жыл бұрын
@@HallmarkPoolSupplies thanks!
@amykendall1338 Жыл бұрын
Would this work to get a rock out?
@HallmarkPoolSupplies Жыл бұрын
It is worth a try, good luck.Thanks for watching.
@stricklandgarageaviation28643 жыл бұрын
Where would a skimmer leak?
@danielskinner63723 жыл бұрын
Excellent video
@emilcioran8873 Жыл бұрын
Just came across this channel. Been watching and liking Mark's videos for hours. The amount of work and dedication he puts into this content to educate and help complete strangers. What a wonderful human being. I am sorry I can't afford a decent donation. Thank You
@ChristIsRisen7779 ай бұрын
I too just found this channel and he's very thorough on how he teaches! Love this guy! 😎🤙🏽
@jaydoh64203 ай бұрын
Completely agree friend
@ERSLIFE-we1mg Жыл бұрын
should my pools water level always be a little above my skimmer? thank you
@HallmarkPoolSupplies Жыл бұрын
The water level should be little under the top of the skimmer so that debris will go into the skimmer. If the water level is above the skimmer, debris will not be able to go into the skimmer. Thanks for watching.
@ERSLIFE-we1mg Жыл бұрын
@@HallmarkPoolSupplies thank you 🙏🏽 so much appreciated
@TheLarryBrown2 ай бұрын
The water level should be about halfway up the skimmer opening. Lower than that and the skimmer may run dry and your pump will suck air and cavitate. Much higher than that and your water will go over the tile line and touch the coping. The mortor under the coping is not designed to be under water and over time that mortor will weaken and your coping will detach from the pool.
@tdata5453 жыл бұрын
SO... I tried this, sort of, but instead of going from the pump end I put the hose in the skimmer hole, and did it, then using the skimmer line lever to create pressure and purge. It's easier to build up pressure, release it, build up pressure, release it, etc. Then it's also going in the right direction through the pump, cutting down on chance of reclogging it when the skimmer is freed. EDIT: THOUGH I did use your video to show me what the theory was. Since before 12hrs ago, hadn't any clue.
@brentskaggs67043 жыл бұрын
Just purchased a home that had this problem. I followed your instructions and it worked out perfect thank you so much for the details and the great advice.
@goldcoast68543 ай бұрын
going to try this today, My fingers are crossed.
@robwasnj3 жыл бұрын
Sometimes that works for sure, we've also used the blowers used to winterize pool pipes to clear the line as well. Doesn't build enough pressure to burst a pipe and for some reason the air and all the agitation seems to get out stuff like acorns, etc. We use a fitted lid and like you did the pinch the hose method we often pulse the valve on and off to get bursts of pressure.
@charlesmcdonald83753 жыл бұрын
Mark……..this is an exceptionally good video. You explained everything in a way that is understandable. I subscribed to your channel. Thank you.
@brianfleischman7973 жыл бұрын
thank you Mark I used your trick and it worked out very well now I am going to buy a vacuum plate.
@billburkhalter4113 жыл бұрын
Great video!! I learned how to unclog floor drains years ago at a restaurant. Works on most washer drain clogs as well.
@sachinwleumas3 жыл бұрын
Finally, something senseable. thanks
@daltongang23 Жыл бұрын
Great video. We are having leaves and pine straw falling by the bucket fulls with more than usual wind and our skimmer basket was full and the pump sucking air. First made sure there was no debris blocking the skimmer door and then tried your hose technique with no luck. Suddenly, it occurred to my husband to check the trap door. The door was stuck so no water was coming into the skimmer. Duh! But glad it turned out to be a VERY easy fix.
@fargo007 Жыл бұрын
This worked. My particular clog was two parts. We got it to move by using this trick as shown, and backing that up by using a plunger on the hole to exert pulling force on the pool side of the clog.
@vadentek2 жыл бұрын
Super helpful video. Thank you for sharing. Going to try it out today!
@crisg.57663 ай бұрын
Would undulating suction indicate a clog? It cycles every few seconds. Sucks decent for 4-5 seconds then slows down and does this repeatedly. We concerned about a clog but are suspicions of a leak. I've checked all the connections for air leaks and everything above ground seems fine.
@HallmarkPoolSupplies3 ай бұрын
It’s possible you have a clog, run the pump on the drain line and close the skimmer. If the pump runs good on the drain then you may have a clogged skimmer. If the pump doesn’t run good on the drain then you may have a clogged pump. Thanks for watching.
@jkintake Жыл бұрын
The repeated back and forth method is great advice. Thanks for also going beyond the basics.