Happymodel Mobula6 Get the hotness! 🔥🔥

[@gmascagni]

I'm using my X-Lite Pro and bound using ACCESS internal module. Eazy Peazy no drop outs. I'm running BF 4.1.1 just use FrySky_X in BF and do a bind_rx in CLI . Go into your ACCESS Radio use ACCESS D16 just go to Bind be about 4 feet away. Go back to CLI type Save. On your Radio back out of the bind. Disconnect USB from FC then connect it back up. Go to Rx Tab and wala you can move the sticks. Been running this way for two weeks no problems one or two dropouts. Warning there is an issue with BF 4.1.2 so I would stick to LEGACY 4.1.1 Dont forget to upgrade your ESC to JESC 2.3 for an extra 30% flight times. :-)

[@sketchpv3080]

Georgio Mascagni - That info is much appreciated. My Mobula6 recently arrived and I was concerned with binding it to my X-Lite Pro.

[@gmascagni]

@@sketchpv3080 Consider upgrading to Project Mocking Bird search on Facebook for the M6. Night and day difference. Correct bind command is Bind Rx_spi I had that incorrect above. Good luck loving my M6

[@FloridaWildlife]

Just bought both, the Mob6 and the frsky Taranis q x7 and have no clue how to bind when they arrive, so ty!! Been flying drones for 5 years and figured I need to learn betaflight at least to get a better fpv experience.

[@thads6192]

Great review. It’s possible to replace the burnt FET with a little patience and the right tools. If you don’t want to fix it and haven’t tossed it, I’ll take the smoked board and pay for shipping to see if I can repair it. Let me know. Thx

[@TweetFPV]

yea, iv'e replaced them before. i don't have time to mess with replacing the FET. if you want it it's yours. Email me at [e-mail]

[@thads6192]

TweetFPV Thx. Email sent.

[@leadslinger5130]

Great video. I'm just getting started in the fpv world and my first 2 quads where the mobula 6 and 7 v2. I totally get what your saying as far as 2s but I do think it's fun as a beginner to have a quad that's fun indoor and riot outside. While I will never have fast enough reflexes to fly 2s indoor out door it a blast.

[@robzFPV000]

Just ordered one. Hope it can live up to my tinyhawk s because I love it indoors and out.

[@thomasfpvandtowing3653]

Thanks for showing smoke. Some reviewers wouldnt I personally know it's so stressful to have to wait for that replacement.

[@DriftFPV]

Great vid. I have had good luck so far with mine. I did however had two of the meteor65 croak before I picked this one up. I am going to load up your tune tonight and give it a try. Thanks!!

[@alexandroslianos6753]

very nice review but you have to put the 25000 kv motors .

[@paulgiusti6779]

Fun video! I can't wait for your video on binding D8 mode with the XJT module. I gave up on trying to get my X9 Lite and XJT module to bind to my micros and just use my Q7S for my micros. It is kind of funny that my five inch I fly the small TX and the micros the large TX!

[@TweetFPV]

I just got the x9 lite s in for review so that's a blank slate for doing this video. I'll have it out soon.

[@paulgiusti6779]

@@TweetFPV Oh, nice! I have been eyeing that X9 lite S. I love my X9 lite more than any other TX I have owned. It has a perfect form factor due to it's full size hand feel a light weight and overall dimensions that fit easily into my backpack. The S model addresses any shortcomings I could think off by throwing hall effect gimbals, internal battery charging, and a couple extra momentary switches into the mix all for a price that still makes it one of the best values out there. And we didn't even talk about the blue tooth or Para trainer goodies yet! Can't wait to hear your review!

[@DemoPwr]

Nice flight, repair and review...Wasup happymodel get it right Just watched 2 videos with Happymodel issues and my Mobula 7 is down... that's the reason why I haven't purchased any Happymodel products..sorry!

[@doktordrone]

Thank you very much for this cool review 🙏🙏❤️🔥

[@TweetFPV]

Thanks for watching

[@MCsCreations]

Awesome review and flying, dude! Really nice! 😃

[@mr.crowley3542]

nice content! Thx a lot! 4:36 min is a lot of time...mine mobula 6 can't fly so long...did you noticed a real improvment flashing the motors?

[@TweetFPV]

Certainly more flight time when flashing the esc to 48k pwm

[@jmoore3854]

A spreadsheet comparing all the model lap times would be nice. Did I hear you ride the mobula 6 avg.14 seconds while the tinyhawk varied 28 to 40 seconds.

[@TweetFPV]

The spread sheet is a good idea. I was talking about the tinyhawk 2 vs the tinyhawk s as far as lap times. That wasn't on this track. That was on a track at a multigp event.

[@novcon]

Great review, I love your videos.

[@TweetFPV]

Hey, thanks for the kind words!

[@WaitingOnToday]

How did you manage to show the battery voltage after two decimal points? I mean 3.33V instead 3.3V?

[@TweetFPV]

That is part of betaflight 4.x

[@WaitingOnToday]

@@TweetFPV Thank you for the answer. Can I flash Mobula6 with newest 4.1.xx firmware or I have to flash it with any specific fm (over 4.x)? I flashed it with the newest version of Crazybee F4 FS (Legacy) and it seems to me that it behaves kind of wobbly. I can see some oscillations I guess compared to 3.5.7. I set everything as it was in earlier firmware. I flashed 48 kHz ESC firmware but it didn't seem to help. Maybe it's just me.

[@sideburn]

Mine has a daughter board. And it has antenna wire. I have three antennas on mine. What’s up with that!?

[@TweetFPV]

Never heard of that. I'm not sure what to tell you on that one. I would love to see pictures of your setup. [e-mail]

[@bradleybeaudry8935]

@@TweetFPV Received my mobula 6 today, and it also came with an extra receiver. I have the 19000kv flysky version. The directions state "if you are not satisfied with the range of the SPI receiver, please use the external receiver". I had no issue binding with the on board receiver, and it flies great in the house. Now I have an extra receiver. Thanks for the great video.

[@TweetFPV]

@@bradleybeaudry8935 wow that's interesting that they come with 2 recievers when you order a flysky version. Probably doesn't weigh 20g then.

[@M.TTT.]

Have you had any vtx issues? It seems like I can go behind a wall and lose reception or practically be turned around and have bad reception. Kinda dissapointed, but I need to test it with less wifi on maybe.

[@TweetFPV]

The VTX is decent with no real unexpected drop outs. You can try and orient your antenna into a more vertical orientation through the canopy. That might help you out.

[@M.TTT.]

@@TweetFPV I think I accidentally had pit mode turned on or something like it almost, will test tomorrow though

[@jillsmith6404]

Did I miss which motors this quad has?

[@TweetFPV]

Yep. It was in the video but they are 0802 19000kv Motors. They also have a "race" version with 25000kv motors as well.

[@dstaron3162]

Good work! Do you have a video of all the firmware updates that you did?

[@TweetFPV]

No not yet but it's pretty easy to do.

[@maeldrz]

Thanks for the vid ! Have you got RX Loss or latence ? Mine has a lot...

[@TweetFPV]

No I can't say I have noticed any rx issues. Are you on d8 or d16?

[@maeldrz]

@@TweetFPV I'm on d8, I can't fly in my house, to much latences

[@TweetFPV]

@@maeldrz you have too much latency in your rc signal or in your video?

[@maeldrz]

@@TweetFPV it was on the rc signal, but think because I flashed with jazzmaverick wrong firmware. With JESC, I have no problem :)

[@TweetFPV]

I had issues with jazmavric desynicing but no problems on jesc. I don't mind kicking him a few bucks for his work.

[@stevenkelby2169]

How do I bind my mobula 6 to my frsky x-lite s? Do I have to buy an external module? I've been reading, watching and trying everything for days and can't get it to bind.

[@TweetFPV]

The best way is to buy a xjt lite module. You can bind some quads in d16 mode but the xjt module is the best option for the best reliability.

[@stevenkelby2169]

@@TweetFPV Thank you for the quick reply. I love your channel! It's disappointing that I can't bind my new frsky transmitter to a new quad with frsky receiver! Guess I'll have to spend the money on the module. I see now why so many people hate frsky!

[@TweetFPV]

@@stevenkelby2169 yea people don't like change. Frsky is trying to move the tech forward and to do that they need to stop with the old stuff. But I do agree it sucks that the rest of the industry isn't following suit.

[@davidGrainger]

@@TweetFPV It's not that people don't like change. It's not that the "rest of the industry isn't following suit." It's that FrSky didn't make the new tech backwards compatible. Spektrum DSMX works with DSM2. Why didn't FrSky make ACCESS work with ACCST? Frsky forces customers to buy extra stuff to continue to use their existing receivers, or jump through hoops as mentioned by Georgio Mascagni in your pinned post, with "no problems one or two dropouts" LOL.

[@TweetFPV]

@@davidGrainger I agree. Also something to consider is that d8 mode is not legal to use in most countries. I'm not going into the politics of a business selling products that don't comply with local communication standards but this is one reason I have heard that frksy is killing off d8 mode. Is it true.... Who knows?