Harbor Freight Replacement Pump on Our Campbell Hausfeld 80 Gallon Compressor

We replace the compressor pump on our 15 year old Campbell Hausfeld 80 Gallon 5 horsepower compressor

[@stickbogart3657]

It would be so cool if KZbin will allow people to post pictures that are related to the subject or the topic. I’m very happy with the compressor I bought from Lowe’s. It cost me just under $600 and now you can touch 1/2 the size for $600. My air compressor is in my garage. Actually it’s in my laundry room. I’ve done a few modifications to it and I enjoy it very much. I always try to keep my tools out of the weather. I put the hour meter on it so I can track the number of hours that I’ve used it. It gives me a good idea when I should change the oil in the compressor. The compressor is a two stage, one big piston, and one small piston I have an electric valve on the bottom of the tank. If I push the button, it blows out any condensation that’s in the tank outside of the garage. I only have to push it for a couple of seconds and everything gets discharged outside. For anybody that wants their tools the last for a long period of time. Keep them out of the weather.

[@i.e.427garage9]

Thanks for watching.

[@TF856]

My dad left his air compressor out in the weather for 20+ years and it never seemed to bother it.

[@i.e.427garage9]

The problem with this one was completely user error. I should have been draining the tank on the compressor and not leaving pressure in it when not in use and the oil change intervals should have been more frequent. Completely my fault.

[@stickbogart3657]

❤ I keep mine in the garage and noise did it makes which is not that bad does not bother me. I just don’t want it to get filthy, dirty and exposed to the heat in Arizona. I did some modifications to it after I bought it from Lowe’s. My air pressure gauge is not one of those super small ones it’s 6 inches from side to side and it goes all the way up to 200 psi. I really like the air compressor. I did put a digital hourmeter on it so it’s counted the hours that it’s ran so far all the way up to 5.1 hours. I really enjoy it. ❤

[@i.e.427garage9]

Thanks for watching.

[@rolandskinner461]

You have a awesome looking shop

[@i.e.427garage9]

Our new shop is even awesomer! Thanks for the compliment.

[@fitch8363]

Thanks for the good video. I recently got rid of a 2hp Campbell Hausfield compressor I bought on sale at Sears ~50 years ago. for $230. It was a fantastic compressor - the pump ran at 733 rpm. It was not irritating to listen to at all. The tank rusted a lot over the years and eventually become unsafe. The compressor started making rod knocking noises, so I replaced it with a 3.7hp 60 gallon DeWalt that is way louder than I expected it to be. Over 100 DBA at three feet. I'll be replacing the pump with one from HF. Hopefully it will be tolerable to have in the shop. Where I live, having the compressor outside is not an option.

[@i.e.427garage9]

Thanks Fitch! We recently moved the shop and didn't want to move the 80 gal compressor from the old shop. We ended up with a new (to us) 30 gallon CH compressor that is much more mobile. Quiet too. Couldn't be happier.

[@nel6211]

Right thinking on switching fittings from the old compressor pump. I have an 80 gal Husky with a bad 2 stage pump. I've been debating buying the HF twin cylinder one you have. A new CH pump is over $700 plus shipping. May have to look into this and settle on that single stage .Good info!

[@i.e.427garage9]

When we looked at replacing the pump with this vs other options, it quickly became a no brainer. Even if it only last a few years, it will be well worth it.

[@TF856]

Never mind the breaker. Put some 3-Way / 4-way switches(that light up when the circuit is on) in different locations so you can turn that on and off without going to the breaker. Like the garage main door and side door or by the work bench. Maybe even on the compressor so you don't have to walk so far when you're working on it. I'm sure that would be easy for you.

[@i.e.427garage9]

I started in the electrical trade 40 years ago. One thing I learned early was, always shut the power off at the breaker when servicing anything. If I'm out on a job, I lock out and tag the breaker. Accidents happen way to easy. We have since moved out of that house (shop) and I've downsized when it come to a compressor. I should have a video out soon with details on the new compressor.

[@CraZYCODplayes]

Yep 3/4 flare fittings. Basically 1-1/16 - 14 ver close to npt which is also 14TPI. Dealing with this problem rn . Good video

[@i.e.427garage9]

Luckily we were able to just swap the manifold and it all worked.

[@stickbogart3657]

It seems to me that you’ve got a nice garage. You have a lift in there that’s good that’s what I used to have at one time I had a 6 1/2 car garage with a lift and a 2 ton overhead chain hoist I was you I put the air compressor in the garage. It will last much longer.

[@i.e.427garage9]

Thanks for watching.

[@cgpd7507]

Just an observation, it looks like the new compressor pulley requires two belts. May need to change the motor pulley and also is the new pulley the same size? They must match up for the right rpm of the motor.

[@i.e.427garage9]

Original pump had higher capacity and a single pulley. It's been working just fine since installed. Thanks for watching.

[@je1279]

They are SAE threads that the compression fitting screws onto.

[@i.e.427garage9]

Thank You.

[@billdavid6315]

I had that same CH pump, the connecting rods ate shit after a few years. CH sent me two sets of connecting rods. They sent me two boxes thinking two cylinders i guess. Well each box contained a set of two. I still have a set

[@i.e.427garage9]

I've had that happen with replacement parts in the past as well. When I called to tell them about it, I've been told just to keep the extras.

[@pontiaco]

Cool video Do you know what's the OD on the electric motor pulley, I just got same but compressor but the electric motor is missing the pulley, thanks

[@i.e.427garage9]

I'd have to measure it but I think it's about 3 or 4 inches in diameter.

[@Roboticgladiator]

I replaced the pump on my 5hp compressor with that same pump from Harbor Freight. I used the recommended pulley size for the motor to drive the pump and it pumps a lot faster than the old tired pump. However, now it tends to overheat the motor with heavy use (air sanders) which it didn't do before. It makes me wonder if the pump requires more than the advertised 5hp. I'm only pumping to 120psi. I'm curious if anyone else has noticed that a 5hp motor is not beefy enough to run the HF pump without overheating.

[@LoneWolfPrecisionLLC]

Motor is probably just old and tired

[@i.e.427garage9]

I think your motor is tired. Maybe time to replace it as well.

[@here_to_watch2115]

They underrate motors. If youbrun the 3.7 hp pump on a 5 hp rated motor itll run with out the overheating.

[@e-racer4673]

I know this is an old video but I just want to tell you it’s a Campbell hoss field. HOSS is what it sounds like Field.

[@i.e.427garage9]

If you say so...............Did they change the spelling just for you? www.campbellhausfeld.com/product/air-compressors

[@mikefennema5561]

Beware of those small cheap gauges. The pump vibration damages them over time. I have a paint sprayer that looks like a balloon because my gauge indicated way low.

[@i.e.427garage9]

I run a high quality regulator with a gauge on it to avoid any over pressure issues.

[@woodys.lasaswoodsons.3068]

I have had mine over a year. Noticed that it slow pumping up. Removed one head and found that one Reed was broken. Called harbor freight and was told that parts for this compressor were no longer available. And these pumps were on close out. Had to make my own Reed will not buy anything from 🎉H R any more. They are selling this pump that you will not be able to get parts for !

[@i.e.427garage9]

This one has been rock solid since we installed it. No complaints.

[@philliphall5198]

Mine is 14 years old and working great. I only go to 120 lbs because that’s all I need in mower shop 80 gallon tank and it’s inside shop with electric cooling fan Wired to when it comes on fan does to. Yes I have friends next door and I give them eggs Lololo

[@i.e.427garage9]

Luckily we are in Southern CA. and don't have to worry about freezing temperature all that often. Ours does just fine outside under the overhang of the shop roof.

[@deondriaballenger5156]

Where to buy replacement pump? part # or model? how many hp

[@i.e.427garage9]

www.harborfreight.com/5-hp-145-psi-v-style-single-stage-cast-iron-air-compressor-pump-60754.html

[@jimmeymcgee2840]

CURIOUS ABOUT WHAT TOOLS YOU RECOMEND IN A SHOP FROM AIR TO BATTERY OPERATED?

[@i.e.427garage9]

I love my M12 Impact driver and both the 3/8" and 1/2" drills. I bought a Ryobi 18v impact gun a year or so ago and never realized how much I would use it. Air tools I use are primarily the die grinder with a carbide burr and the air chuck to inflate tires.

[@vim_usr2753]

What v belt did you end up using?

[@i.e.427garage9]

Same one as before. The mounting base for the electric motor is adjustable, it slides.

[@bmxbarron]

how does the motor do outside? in the rain and cold/hot seasons?

[@i.e.427garage9]

It's covered by the overhang/roof on the back of the shop. But in inclement weather I throw a tarp over the whole thing just because.

[@philliphall5198]

It just shortened life of it plus if comes on during ice days kiss it bye Put it under a shed or inside with cooling fan

[@billdavid6315]

@@philliphall5198 I leave mine outside like the pros, I don't wanna hear that shit inside. And fuckers putting a shed around it cooks them. Run nice and cool outside since 1984 blazing hot summers and rain, sleet or snow

[@rondellschuyler7074]

Placing air compressor outdoors is bad, because of excessive moisture. Plus maintenance is everything. Change oil often..

[@i.e.427garage9]

We're in California, so not a lot of weather. Many folks don't want a noisy compressor inside the shop. As for maintenance, I believe I covered that in the video. I should have done better changing the oil.

[@beanhole69]

Ah so you put it outside for your neighbors to hear. Nice. @@i.e.427garage9

[@stickbogart3657]

Makes a lot of noise 😊

[@i.e.427garage9]

Thanks for watching.

[@maintainingmomentum]

Contactor.

[@i.e.427garage9]

Thanks for watching.