{792} How To Convert 110 Volt Power Supply To 220 Volts

[@ukrainehamradio]

Very simple and useful explanation! Thank you very much! Be health and safe!

[@HaseebElectronics]

it is my pleasure

[@gopalarao8578]

Hi brother..,Namaskaar. When I watching your videos I feel working on any circuit board is very very easy. Thank you.have a great day 🙏

[@HaseebElectronics]

It's my pleasure

[@W1RMD]

Thanks! I love these SMPS videos. Thanks for sharing and happy Monday to you!

[@HaseebElectronics]

You are so welcome!

[@deadshotpadilla9848]

I became your student now..thank u for sharing

[@HaseebElectronics]

Thanks and welcome

[@dantronics1682]

Just a quick question, the 2 *330 200v were in series so why didnt you reuse them? effectively they will be 165 uf at 400v

[@kenarf3332]

same quastion.

[@consolechips]

When you’re using a bridge rectifier to convert 230V AC to DC, here’s the calculation: 1. Calculate the peak voltage of the AC signal: • Multiply the RMS voltage by the square root of 2 (which is approximately 1.414). • 230V multiplied by 1.414 equals roughly 325V. • This 325V is the peak voltage of the 230V AC signal. 2. With a bridge rectifier: • The output will be pulsating DC with a peak of approximately 325V. It is always safer to use capacitors that are rated to the peak voltages just in case one fails and the other will go down with it.

[@temyraverdana6421]

A great solution. Thanks for teaching this

[@HaseebElectronics]

Very welcome

[@Hadadoh]

I successfully diagnosed and repaired a laptop charger with a burnt current sense resistor. Previous I had only been able to repair the ones with a blown main electrolytic capacitor. Thanks to your channel and diode gone wild. Currently I have a general overview of an smps power supply.

[@gauripartapshanker9197]

Knowledgeable and informative vedeo thank you so much.

[@HaseebElectronics]

My pleasure

[@randyagnes2997]

hello haseeb, what is that soldering iron with desoldering pump and where did you buy it?

[@qasimgujjaruk]

Great work Love from England UK Keep it up 🌹❤️🌹

[@HaseebElectronics]

best regards and special thanks

[@HarlavanisPanagiotis]

Awesome video dear friend, have a blessed weekend 😊

[@HaseebElectronics]

best wishes and sweet regards

[@nagarankush]

Sir is it possible to convert a SMPS of input 220v to input 110.

[@gerardsunderaj1420]

You need to apply thermal paste between the bridge rectifier and the heat sink.

[@panasotaelectronics8005]

Ma sha Allah sir thats great video for us.its very helpful video

[@HaseebElectronics]

It's my pleasure

[@arun.karekar]

Very informative....thanks sir ji.....

[@mtrltoolman]

Wonderful informative video sir! Thanks!

[@HaseebElectronics]

best regards dear brother sure i will arrange to explain the feedback circuit very soon. i noted it

[@daberechinwobi9299]

Won't it affect the transformer winding

[@HaseebElectronics]

no. as the existing 110v configuration also provides 310VDC at dc rail. as the 220v modification will now cause to increase voltage at dc rail. please check video number 788 for more details

[@vijayakumarkumar9190]

Very good and useful information sir thanks for sharing this knowledge to us

[@farooqzaman7496]

Ma sha Allah Good information sir

[@hugoegon8148]

Good idea! I would let the capacitors installed, just delete centre connection. As MOV on 230 V input usualy 275 Volt types are used. Why you choose 420 V?

[@HaseebElectronics]

if we remove center connection, the capacitance will become 330/2 = 115uf. and the power supply will start fluctuation. we need to use 330UF capacitor it is good to use 275 to 480V RMS MOV in second stage protection. as it is connected in between EMI filters, so it protects form the ringing of the EMI filter higher voltage range as 330-450V is much suitable at this stage

[@hugoegon8148]

@@HaseebElectronics Did you test this? I doubt it, because the circuit after the caps "saw" these series caps before and worked fine. If you change only the way how the caps will be charged (from 110 to 220V) the capacity for the following circuit could remain the same.

[@name1sname244]

Hi related to inverters What is the function of the cap across the battery please

[@ziadfawzi]

Thank you very much for this information. Can l use this method with any 110V power supply please? or it will work only if the power supply has the same design like the one in video.

[@HaseebElectronics]

if it using this configuration, it will work in that time if we have single capacitor, then we need step down transformer. that will much safe solution

[@feebyewok]

Terima kasih telah berbagi cara merubahnya saudaraku🙏🙏

[@CliveTrezona]

This was very interesting. Thank you.

[@HaseebElectronics]

best regards

[@electroniquepassion]

Good information 👏👏👋

[@1greatcommission]

Love you sir. Pls will the pulse xformer still be safe to use for long?

[@akimelectronique]

TRÈS BONNE VIDEO. DIS MOI FRÈRE, AS TU MODIFIÉ LA TENSION DE DÉMARRAGE ? NORMALEMENT L'OSCILLATEUR VA RECEVOIR UNE TENSION SUPÉRIEURE

[@julianhilaire1762]

Why is it in converting 110 volts power supply to 220 volte the secondary side of the power supply's voltage does not increase but remain the same. Can you explain to me please

[@alanp7]

the voltage on the output doesn´t increase, because there´s a integrated circuit that manages the cicles of PWM (on the cold side of the board), and this IC is coneccted to a transistor and the transistor to the chopper (high frecuency transformer, the big yellow block) .If the main supply increases from 110 to 220v the IC changes the cicle automatically to adjust it to the desired voltage (12 volts, 5vsb). I have the same question years ago when I was learning about SMPS, I hope my answer helps you!.

[@AyansolaAfolabi]

​@@alanp7thanks for this useful info. I'm also confused if the cold side voltage or current won't increase after this modification, now it all make sense now. Thanks.

[@hichamtassi1753]

Very useful. Could we use the existing capacitors and make them in series or the total capacitance value will be too low ?

[@HaseebElectronics]

i already recorded a detailed video. it will be published in upcoming days. because many viewers asked this question. we can use both 220v capacitors in series but it is best to use single 400v capacitor. because in series the capacitance will remain 330 uf but its ESR value will increase and also the center pins will create parasitic inductance or stray inductance, which will decrease the capacitor efficiency

[@hichamtassi1753]

@@HaseebElectronics I just saw your video, thank for the explanations, i ignored the ESR parameter. Thank you

[@palwindersandhu2031]

Excellent sir.................Thanks

[@natnaeltmariam4872]

You are very good. Thank you for the video.

[@HaseebElectronics]

best regards

[@muhammadishtiaq24]

Excellent explain thanks for sharing

[@HaseebElectronics]

best regards and special thanks

[@m9xm9x]

great video and much knowledge do you have video on convert 220v to 120v xbox clasic v1.6 psu?

[@arabindatuladhar3861]

great explanation sir ,very helpful

[@Edmorbus]

Keep up the good work

[@HaseebElectronics]

most welcome

[@JAMSHIDMOBILELAB]

MashaALLAH good job 👍🏻 ❤❤❤❤❤

[@HaseebElectronics]

best wishes dear brother

[@JAMSHIDMOBILELAB]

@@HaseebElectronics I’m very much obliged to you! ❤️

[@kaizen1071]

Harika bir video olmuş. Teşekkürler kardeşim. Sen bu işin ehlisin.

[@HelgiThorisson]

That was very informative.

[@HaseebElectronics]

it is my pleasure

[@inforclin]

Sou seu fã... parabéns

[@HaseebElectronics]

muito bem-vindo. fique abençoado

[@tksalalah]

Does primary ic pwm need any modification. As I have Yamaha ats1080 that input 120vac I need to modify its inner power primary section at 220ac is this possible plz reply or I need to buy step down adapter

[@HaseebElectronics]

i suggest to watch video number 894 & 792 before conversion if you will modify as in video number 894 then no need to alter PWM IC section .

[@Magsyboy]

Can you make xbox 360 fat falcon, or jasper power supply 220v conversion

[@ramakantsingh728]

Brilliant information

[@HaseebElectronics]

it is my pleasure

[@abrhamteshome34]

Thank You

[@HaseebElectronics]

You're welcome

[@Sachinraik]

Hi sir I'm looking a suggestion. I bought a new 220v xbox one supply . But when I connect this adapter to the power socket entire house trips. All other appliances works fine on the same socket. Any suggestions on what could be wrong?

[@HaseebElectronics]

that power adapter have short circuit. it needs to test it carefully

[@Sachinraik]

@@HaseebElectronics Can a TV repair guy can test and fix this ?

[@Franco_FC]

Hello haseeb, I have a 12v 40A power supply, it has a problem that when it is turned on without a load the output voltage is 19-21v and when a load is put it stabilizes at 12v, it has the KA7500 integrated, I already checked the feedback and Everything ok, my suspicions are in the transformer, when it is without load it makes a rather annoying high-pitched noise, what do you think it could be? the IC or the transformer?

[@HaseebElectronics]

the ic and transformer are looking good. if it is providing enough output power then there is nothing wrong some power supplies need dummy load. if there is a dummy load resistor in output. check it if there is no resistance you can Install 100 ohms 2 watt resistance at output Terminals I think it will solve the problem

[@Franco_FC]

@@HaseebElectronics Thank you so much

[@mtrltoolman]

Sir, can you please make a video about feedback circuit in smps power supplies that nit have a tl431 ic and some other with no optocoupler. For example the power in video #749. Thanks in advance.

[@ktm3883]

good job ❤❤❤❤

[@bertor111]

Good job, I don't think the capacitors should have been removed. Can you explain why they were replaced?

[@kobeteey4570]

that because the older caps highest volt is only 200v .. in order to convert 110v to 230v you need higher volt caps .. if u use the older one it will explode .. that why he change the mov also .. and he also check the brigde rectifier.. same thing

[@bertor111]

@@kobeteey4570 but when he removed the ac line from the middle of the capacitor, the capacitors are in series 200+200=400v!

[@kobeteey4570]

@@bertor111 its for safety purpose .. he use 400v and 450v .. more volt the better

[@husseinshnati5522]

Is this funny safe and guaranteed it’ll work I’m taking it to a shop but they said it’s not guaranteed but if I took the risk and did it anyways would that blow up my Xbox or just the battery I need answers asap please if anyone has any information I would really appreciate it!!

[@husseinshnati5522]

Fully*

[@sersheva]

Thanks for your video. The new voltage will be aprox 330Vdc, the Vds max of main switching Mosfets needs to be more than 330Vdc I think that has to be taken into account also.

[@TheMrRezystor]

The mosferts are getting the same voltage as before. Previously the capacitors were in series, and each was charged to about 160V (peak of 110V AC).

[@محمودنجيبالقط]

My adapter doesn'thave the same jumpers how can I convert it ?

[@ssmm3630]

thanks a lot

[@HaseebElectronics]

You are most welcome

[@ssmm3630]

​@@HaseebElectronics thank you . I send a gmail for you than I have a question .

[@olusegunlateef7571]

great work

[@HaseebElectronics]

Many many thanks

[@isaacattigah5595]

Thanks 🙏🏽

[@juancosta200]

For ps2 110v ton220v??

[@lockdowntimepass7019]

Sir ji 5kw 48volt inverter kaa two igbt module see simple inverter yaa igbt module drive circuit banane dhaneyavaad

[@jackssesanga7601]

dear sir, more video on this 🙏

[@HaseebElectronics]

sure

[@jackssesanga7601]

@@HaseebElectronics and basic diagram or explanation on how common PSU works with SMPS

[@susantaatha6468]

Nice explain

[@englishrupe01]

Really useful tutorial, thank you.

[@shefqetkaralliu6816]

Grazie 🤩❤️👍

[@HaseebElectronics]

best regards

[@wilsonluilui]

HELLOW SIR,I have a charger input is 110v output is 7.2v but the CIRCUIT ONLY have one 250V CAPACITOR supply to point A and B not like your video circuit can i change a 400V capacitor can work .

[@electronicshelpcare]

Good

[@Kricris]

I need the same process but for a gamecube power supply, from 110v to 220v

[@davidsonkofi858]

Real electronic technician brain at work

[@joeatact]

Good Job

[@HaseebElectronics]

best regards and special thanks

[@mushtaqobaray7529]

V good info

[@SujitChatterjee-h5y]

I watch your all videos, very useful videos, thanks for sharing. I need 110 volt to 220 volt DC 16 amps SMPS, normally not available in market. If you suggest me some circuit it will be helpful. Thank you so much

[@allaal8139]

Good job please sir what I do to change my 220Ac\24 power supply to 110Dc input 24Dc output

[@bican4397]

selamün aleyküm üstat, bende tam olarak bu konuyu arıyordum, elimde aynı smps trafosundan var ve 5-6 tane, primer katındaki komponent bozulmuştu, hepsini degiştirdim fakat kısa devre kalkmadı, devreyi incelerken aşina olmadıgım bir köprü diot bağlantısıyla karşılaştım, köprü diotun AC volt girişleri, jumper ile kısa devreydi neden böyle yapıldığını anlamaya çalışıyordum ve internetten de araştırdığım halde bir bilgiye ulaşamadım dün, fakat bugün senin videona rastgeldim iyi oldu, bilgilendirmenden dolayı çok teşekkürler, Allah CC razı olsun 👋😊

[@iofirm7454]

110V 전원 공급 장치를 220V로 변환하는 방법

[@razaelectricaltips]

Asslasmalkaum, bhai mashallah nice sharing information video good work 🌻🌷🍁🥀

[@HaseebElectronics]

Many many thanks

[@HaseebElectronics]

wa alaikum salaam bhai

[@carolinediyandvlog]

Big like 54 super filmik pozdrawiam serdecznie i życzę miłego tygodnia 😄👍

[@DARK__KING]

شكرا جزيلا

[@AbdulMomenZargar60]

Walikum Salaam Jee Aap Ka Good Name Keya He

[@vkproduction1166]

Sir if i need to use my smps with 90 volt how can I do it ? Let me say my questions i have a battery of 92 volt dc battery I need a conver to 12 votl output How can I do it ? I am useing a ac smps I can use the dc voltage because it will convert ac in to dc so i thought to give the power supply in the dc line at the capacitor i need some help I need to chaing the winding of the smps please reply I love you video ❣️

[@MalikArshad477]

bhai jan mujhay 600v to 24 volt ki pwer supply banani h 220v ko 600v ma uprade krny ka triqa btadn plz🤌🤌🤌

[@nayanjagirdar8408]

👌👌👌👍

[@rashminaik6039]

Great....

[@HaseebElectronics]

thanks a lot

[@saifurrehmanshahid4669]

Why you removed my comment I didn't say anything wrong to you.

[@HaseebElectronics]

no brother i don't remove any comment either if there is any comment is negative or hateful. it is opinion of my viewer. so respect the opinion of my viewer. sometime KZbin holds some comments like spam words. that are blocked by youtube community privacy etc. otherwise every comment is valuable for me

[@HaseebElectronics]

i remember that i never saw any comment from your name ( Saif ur Rehman Shahid) please write your comment again as a new comment or you can send to my whatsapp [phone]

[@saifurrehmanshahid4669]

@@HaseebElectronics I try to add a website address for the reference to see how simplified the 110 to 220 conversion with same capacitors.

[@HaseebElectronics]

oh yes website links are not allowed in comments for my channel you can send whtasapp 00962-79-5324272 or Gmail I'd [e-mail]

[@meassavuth4649]

❤

[@tvbox8478]

👍 ✋

[@HaseebElectronics]

best regards

[@MrGigglesGalore]

Wtf extremely confusing

[@dumitruoancea977]

I

[@Edmorbus]

Excellent explain thanks for sharing

[@HaseebElectronics]

best regards