{1146} Beko washing machine control board troubleshooting

Рет қаралды 5,015

Күн бұрын

Пікірлер: 41

@karltest1314 4 ай бұрын

Really good video. Another way, before cutting the track at 14:35, if you inject 1v 1A (or 2v in this case) where the removed cap was, you should feel the shorted component get warm. You can detect the warmth by thermal camera, blowing the board with freezer spay so that ice forms, or the back of your finger. 2A works better but higher you go more chance of overheating the track Thank you for the video

@abdulazizbinsaleh4730 4 ай бұрын

Thank you for the vedio. These controller mostly have a firmware that is difficult to find for appliance. Even if the ATMEL controller is available the firmware will note be available. Thanks

@tekno-tekin 4 ай бұрын

Ürün yazılımı açık sağlam olandan çekip atılabilir.

@HaseebElectronics 4 ай бұрын

program can be copied from similar model MCU we need M64+ ADP AVR Programming Adapter Socket for ATmega64 TQFP64

@mohsenSL 4 ай бұрын

@@HaseebElectronics I think frameware with this model is locked. Can't be copied The pcbs are designed for you in a very bad way. Any fault on the output of the board is kill the microcontroller

@vijayakumarkumar9190 4 ай бұрын

Very good and useful information sir thanks for sharing this knowledge to us

@HaseebElectronics 4 ай бұрын

best regards

@Trucam2020 4 ай бұрын

Haseeb, Thanks. You a true master.

@HaseebElectronics 4 ай бұрын

You are welcome

@W1RMD 4 ай бұрын

Great diagnosis! I assume that these ATmega a64 microcontrollers are not replaceable. Looks like even if it were available, you would have to program it and too many pins close together to solder, although if it could be soldered, you would be the one who can do it. Take care!

@8500gtNvidia 4 ай бұрын

Thank you for this video Master Haseeb! Very nice knowladge

@alterybabylon 4 ай бұрын

Analytic trouble shooting found the. culprit thanks for sharing

@HaseebElectronics 4 ай бұрын

yes when we find the reason of dicontinuation that is satisfying

@MizanurRahman-sz5yw 4 ай бұрын

Nice Investigation....Thanks Brother.....

@muhammadishtiaq24 4 ай бұрын

Thank you so much for sharing this informative video keep sharing❤❤

@hugoegon8148 4 ай бұрын

Very good analysis. Thank you for sharing. 👍🙂

@6689hamza 4 ай бұрын

بارك الله فيك اخي حسيب

@rolanddejesus8685 4 ай бұрын

thank you very sir for sharing this video...

@ministeriomundialliberando8403 4 ай бұрын

Very helpful, as always. So, if I replace an ic, let's say one RTL8196E, do I need to reprogram the new one in order that it can works?

@yamansaadO Ай бұрын

وعليكم السلام ورحمه الله وبركاته ❤

@giorgostexnikos6976 4 ай бұрын

excellent analysis

@josephshantimba8124 4 ай бұрын

Thank you for your important information

@gamiwv 4 ай бұрын

Is it preprogrammed ? Do you have a "dump" of the firmware (and a programmer) to program a new one ? AS EVERY TIME efficient damage approach !

@HaseebElectronics 4 ай бұрын

program can be copied from similar model MCU we need M64+ ADP AVR Programming Adapter Socket for ATmega64 TQFP64

@pr-ts1jl 4 ай бұрын

Good job .

@stoptheirlies 4 ай бұрын

Hi Haseeb, good video, what de solder station is that you are using please. Bob

@chinnarao326 4 ай бұрын

Resp Sir! Very Nice Vedio Sir. Sir Microcontroler New Replacement Sir or Non Repairable Sir. Or New Controler IC is there Market Sir or not available Sir. -- ChinnaRao Paderu Andhrapradesh

@HaseebElectronics 4 ай бұрын

if microntroller is damaged, then it is better to destroy it because most of the microcontrollers are locked

@mimisabu2121 4 ай бұрын

Emeğinize sağlık hocam

@kaizen1071 4 ай бұрын

Teşekkürler Eşref hocam . ❤❤❤

@mouhamedreda8768 4 ай бұрын

Toujour le même problème dans cette carte mère beko ( court-circuit au micro contrôleur )

@anwarjamal8908 4 ай бұрын

Sir what is the used of inductor in power supply secondary side and inductor calculations

@davidhollfelder9940 4 ай бұрын

The old/defective microcontroller likely has (or had) custom firmware/code in it. How would you get that? BTW, my 20+ year old Kenmore washer, still has the original mechanical timer, and still works. As with all the new/newer modern cars, they’re full of these specialized electronic modules, that will soon be no longer available. What then? PS, in the near future, I see a whole field emerging, replacing these with emulators, using Raspberry Pi or Arduino computers and hat/add on boards.