Ok so here's the story about putting it back together the camera died and I didn't know it so you'll not be getting that video you'll be getting the Chrono test and accuracy with the hammer spring adjustment
@restolsarlАй бұрын
get yourself a few Euro /Dollar rubber doormat, the ones with the "mudholes", you can park your screws and parts in them, and it prevents scratching everything!!
@shaneburnett2881 Жыл бұрын
This video is awesome. I have been looking for this a year now. Thank you. I did almost 2 turns. Went from 5 mags to 4 mags per fill. Reassembly was very easy. Im shooting .177 calibre. With HN Baracuda Hunter 10.49gr i was getting 18ftlbs. When i test again i will post the improvement
@airpower7692 Жыл бұрын
Cool thanks. Let me know how it goes
@kmom777 Жыл бұрын
Thanks to that video more people will fill comfy to buy the in invader knowing how to disassembly and and do lubrication
@johnnybbgunner21369 ай бұрын
You and I both need a decent rifle stand/work bench. Great video.
@airpower76929 ай бұрын
I finally just got a folding table it works great
@asoasotriadio Жыл бұрын
The first one to make a video on it good job. Are you going to cut the stock like you did with the blitz or leave it as it is?🤔
@airpower7692 Жыл бұрын
Leave this one like it is
@airpower7692 Жыл бұрын
Chronograph tomorrow
@asoasotriadio Жыл бұрын
Hey Roy, can do me a favor? Could you measure the gap where the magazine fits? I would like to know what is the longest pellet that can be single loaded
@airpower7692 Жыл бұрын
15mm good luck getting your fingers in there
@shaneburnett28817 ай бұрын
I need you help. Sometimes the rifle does not cycle. The bolt fails to go all the way back to ready the next shot and i have to cock it manually
@airpower76927 ай бұрын
Sounds like a bad old ring around the cup in front of the barrel or the cup is not in the proper position or you have a bad magazine try to let it cycle without a magazine
@jasontan79208 ай бұрын
I want to be sure we can remove airtube with air? Then replace another one sith air too?
@airpower76924 ай бұрын
I can't remember i don't have the gun anymore to go check
@user-ip6dh6pt2l4 ай бұрын
How is you hatsan invader now? Would you still recommend the hatsan invader? Im planning to buy a semi auto pcp rifle. Or other suggestions? Thanks
@airpower76924 ай бұрын
I only had it a week and sold it but the guy i sold it to likes it and it still doing good
@EDETAN754 ай бұрын
Hello my friend, what was the purpose of disassembling the weapon to give it more power? I have had the same one for a month and I would like to know if this way the invader is given more power, thank you and greetings from Spain.
@airpower76924 ай бұрын
Should have a video on the power level after i did this and before because i can't remember the results that far back but it got more power but you lose shot count cause of more air use
@@airpower7692 Thank you very much friend for answering so quickly, I don't mind losing a few shots, what I want is to get a little more power, I will wait for the warranty to pass to modify it, from today I subscribe to your channel because it is very interesting and you are the only one that explains how to dismantle the hatsan invader on the entire network, greetings from Spain.
@EDETAN754 ай бұрын
@@airpower7692 Thank you very much
@airpower76924 ай бұрын
@@EDETAN75 your welcome. I do this to just about every air gun I've owned so far
@peteralexben Жыл бұрын
hello i would like a shooting rest/vice to support the gun ,to get the hands free. use some heat to get the locktite broken ,where possible
@vr6516 Жыл бұрын
Hello, can we loosen more than two turns? Thanks.
@airpower7692 Жыл бұрын
Yes maybe up to 4 but your shot count will drop way down to around 3 maybe 4 shots if lucky
@raybaker1841 Жыл бұрын
That’s the only way to adjust the hammer spring, to take it apart?
@airpower7692 Жыл бұрын
You don't have to take it all the way apart just take the stock off then loosen that set screw on the hammer and then turn the adjustment screw in the back counter clockwise and tighten your set screw back. I took mine that far cause I couldn't break set screw loose
@user-bf1wq6xn9h Жыл бұрын
Hola mi problema es que el mio dejo de autogarce solo osea tiras el primer disparo y no se vuelve a cargar 😢 que podria ser el problema ?
@alvaromilla1982 Жыл бұрын
😂 que pones mal los balines en el cargador
@gumbystown Жыл бұрын
Already taken it apart
@airpower7692 Жыл бұрын
Yep! Put it back together to but the video camera died
@user-bf1wq6xn9h Жыл бұрын
Hola mi problema es que el mio dejo de autogarce solo osea tiras el primer disparo y no se vuelve a cargar 😢 que podria ser el problema ?
@airpower7692 Жыл бұрын
Could be a number of things like the switch i describe in another video that's behind the trigger or it could be in the trigger assembly itself i really couldn't tell you I'd have it in my hands working on it