Great job of making this very easy and simple to do. I replaced the bulb on my wife's 2007 Dodge Durango about 4 years ago and I wish this video was available then. I replaced the bulb via the trap door area back then because I didn't know there was a 10mm nut that needed to come off the back side. Compounding that problem was the red grommet thing that was still on after removing the old bulb and you can add 20 minutes of cussing until the grommet happened to fall off by itself. That was torture. Without recording the video of me doing this today it took me 5 minutes. Mike, thank you. Great video and tutorial.
@LeftieLori8 жыл бұрын
One of these days I'm going to come to KZbin first. Thanks for the video. Worked perfectly for my 2007 Dodge Durango.
@scottlemus97533 жыл бұрын
BEST VIDEO EVER!!! Took me under 20 min to replace both. Thanks 🙏🏼
@ms.mommie69858 жыл бұрын
Thank you a million for this video. It saved me $65.00-$100.00 to have a signal bulb ($6.00 for a pack of 2) changed by a mechanic.
@nickmenster92772 жыл бұрын
Thanks for the video! Helped out tremendously.
@orlando59132 жыл бұрын
Really helpful video. Thanks
@420frankp4 жыл бұрын
Why remove the housing when you can access the bulb through the wheel well?
@cameronearnshaw22597 жыл бұрын
Some of the directions I have seen show two nuts behind the access panel, but mine only had one, as in the video. You still have to pull HARD on the housing to get it out once all the nuts and bolts are loose because there is a ball and socket that holds the housing in place even when everything has been loosened.
@trendx2854 жыл бұрын
Just changed both sides. Thank you very much
@CombatArmsSapper8 жыл бұрын
Thanks for the video, I never would have found that rear connection under the wheel well without it. Great job!
@russellcox90378 жыл бұрын
this was a real help, I had no idea where that 3rd but was or how to get to it. I even had the same grommet issue on the drivers side! hilarious!!! thank you very much!
@tjrooger10925 жыл бұрын
FWIW... If you're only doing the headlight bulb, you can work through the little access flap under the fender. Then you don't need any tools, or even have to pop the hood. Takes about 3 minutes, if your hands are small enough.
@danteboutthatbiz18757 жыл бұрын
Thank you so much for this video i was told it would be $100.00 for me to get my headlight changed i can do it myself now!
@randomconsumer44943 жыл бұрын
You just did the exact same thing I did.............. I fucked with it for 20 minutes. Dude....
@jvasseli7 жыл бұрын
Concise, informative. Just an amazing help. Thank you!
@fredf5218 жыл бұрын
thank you for posting this excellent video. I cannot believe the ridiculous design for changing a headlamp. you were lucky that the wheel cover vent was torn off. It scratched the s**t out of my hands maneuvering inside that small space, especially with the tire in place. I suspect someone tore it off out of sheer frustration. Thanks to you I am no longer a one light "padiddle"
@LeftieLori8 жыл бұрын
I was lucky my hands were small enough to fit. That was a crazy place to put a nut.
@cameronearnshaw22597 жыл бұрын
Not really too bad. Just need a 10mm socket with a 6" extension and it's a piece of cake. The hard part was knowing where the hidden nut was. Thanks to the video for showing that.
@b.arturom.73664 жыл бұрын
Thanks MIKE WADE just changed my lights!!
@henryklassen33627 жыл бұрын
Thank you for the video, I took the top 2 bolts out but couldn't take the light off, and now I know why, there's a nut on the bottom, thanks.
@Chuckufarley246 жыл бұрын
Great video. Thanks!
@LuisLopez-ve5jt3 жыл бұрын
Amazing video! 👍 All done with only one hand!!! I bet this guy would be a great camera man, if you know what I mean! 😉
@theycallmedonkey66642 жыл бұрын
Hey I don't mean to be an ass but I just reached thru that "nut access" twisted the bulb out and changed it that way and didn't have to pull the entire assembly... just a thought
@sw3dishla8rat4 жыл бұрын
Thanks mike!,,,my problem I have a 2007 aspen,,every time I install a new bulb on the passenger side it lasts for about a week and then goes out again,,,there must be a short somewhere causing it to blow?, thoughts?
@nasmr12342 жыл бұрын
Very Clear
@frankmashione1393 жыл бұрын
Thank you went smooth
@pattonchannel917 жыл бұрын
Thanks a million for this video! Note to viewers! Watch the whole video! The old RED grommet was what about sent me to the looney farm. Then I watched the whole video.
@_adams_46248 жыл бұрын
This saved my day! Thanks for putting it out here. 👍🏻
@mannypaulin66044 жыл бұрын
You are amazing. Thank you
@christianyenzer25244 жыл бұрын
I just changed the lights within that little door with out taking the whole light housing off thanks
@markc73675 жыл бұрын
I would have never guessed where to access the fenderwell bolt on my 2008 Aspen. I think i will replace all 3 on each side while i have them out. I also have some moisture beads in mine im concerned about. Also need to point them lower if possible. Always getting the hibeam flash from oncoming traffic.....? GREAT VIDEO !!! MANY THANKS!!!
@SeanJonesYT6 жыл бұрын
Thanks mike! Great video. Unfortunately while taking the nut off the back, it along with my extension fell into the wheel well. Do you know of any good way to get to this area so I can fetch those back?
@agent6t86 жыл бұрын
Sean Jones can you get to it after taking the headlight out? It should open everything up. Good luck!
@caseysmith94566 жыл бұрын
Can't you replace the bulb through door in wheel well without removing the entire housing? I can see the bulb through the door in the video. Seems like that would be easier and possibly the whole reason the easy access door is there
@agent6t86 жыл бұрын
Casey Smith you have to remove the housing, it is by design. If you could somehow remove the old bulb, it would be nearly impossible to put the new one in without touching anything. Any contaminants on the bulb, especially oil from your skin, will greatly reduce the life of the new bulbs.
@caseysmith94566 жыл бұрын
Mike Wade I had a bulb go out last night which is why I watched your video. Today I bought a new bulb and used the access door method to replace it. It was hard to see what I was doing and the tight space made it difficult to maneuver but I was able to replace it in about 7 minutes using only a screwdriver to open the access door.
@patriots1on15 жыл бұрын
Casey Smith did you have to break the access door to get in there?
@aaronporter80247 жыл бұрын
OK !! now does your truck have that same small trap door in the wheel well ?? and do u also have to have an extension piece to remove the housing unit the same way in this vid ???
@Karopine4 жыл бұрын
Great vid. liked/subbed
@xtremejaimeable6 жыл бұрын
Can I put Aspen headlights and grill on Dodge Durango? Have a Durango but would like to add a few parts I see in the Aspen.
@agent6t86 жыл бұрын
Jaime Gabriel Quiles the entire front end is different. I am sure it is possible, since the Durango and the Aspen share the same body, but you would be replacing -everything- from fenders, flares, hood, etc. And even then, the doors may not line up.
@alvarosalazar8682 ай бұрын
Thak you👍🏻👍🏻
@loriweinkechristianson34826 жыл бұрын
I have a 2011 Gran Caravan Crew can't find the exact way to change my bulbs. Can I get some help please?
@jhickey95765 жыл бұрын
Or if your hands are small enough.
@savoiejp7 жыл бұрын
I was able to change the bulb on the Durango 2004 I had without removing the headlight. Does not work on my Aspen 2007 though
@aldw407 жыл бұрын
Thank you!!
@aaronporter80247 жыл бұрын
I also have an 07 Chrysler Aspen and the thing I couldn't do was take the whole housing unit off to change the bulb to I took the truck back to the dealer and had them change out the bulb for me !!!
@cameronearnshaw22597 жыл бұрын
You have to pull hard to remove the housing, straight out the front, even after everything is loose!
@DjKamikazee8 жыл бұрын
good video
@zackskinner43835 жыл бұрын
Can do this on 08 aspen awd 5.7 just need flat head
@GoodGuyy7026 жыл бұрын
Thank you
@VL9796 жыл бұрын
How do you replace the wire harness to the light bulb?
@agent6t86 жыл бұрын
VL979 that I do not know. If you have damaged the harness somehow, it is probably incredibly easier (and cheaper) to splice new ends than it is to replace the entire harness. If you need to replace everything for some reason, I would suggest you take the new harness and use it as a guide to remove the old one, replacing everything as you go. That harness is likely integrated in to many things, so be ready for a lot of disassembly.
@VL9796 жыл бұрын
Mike Wade thanks bud, I ended up jus splicing the ends off and put in the new one. Thanks for the tips though.
@muggaphilly20723 жыл бұрын
Did you know you couldve changed the bulb under the wheel well where yours was broken at🤦🏿 Thats why cheysler/dodge made that entrance no need to remove the housing.
@gijr99983 жыл бұрын
size of the bulb??
@agent6t83 жыл бұрын
Hello, sorry I don't remember, I just went into Autozone and told them what I needed and they gave it to me.