HEAT EXCHANGER BASICS | CLASSIFICATION | MODE OF HEAT TRANSFER | PIPING MANTRA |

  Рет қаралды 26,520

Piping Mantra

Piping Mantra

Күн бұрын

Пікірлер: 13
@khosrosafaie9761
@khosrosafaie9761 2 жыл бұрын
Great 👍🌹🎉🌹👍
@maheshnevase9650
@maheshnevase9650 4 жыл бұрын
Kindly make video on heat exchangers drawing reading And its internal parts And its maintenance procedure
@Naresh-mu4ws
@Naresh-mu4ws 3 жыл бұрын
Hello mem I have Small doubt in one pipe line will install one control valve why upstream and downstream pipe line was reduced
@PipingMantra
@PipingMantra 3 жыл бұрын
To have on size lesser control valve which cost less
@Naresh-mu4ws
@Naresh-mu4ws 3 жыл бұрын
In some gas lines one place line was expanding and some places reduced what is the reason mem
@cck0728
@cck0728 6 жыл бұрын
As usual excellent video. Why to roll the pipe? Is there any effect of pipe rolling on process ( fluid characteristics)? Thanks for your valuable time.
@PipingMantra
@PipingMantra 6 жыл бұрын
Sorry Abid i dont understand your Question. could you please mark timing where I talked about it. however rolling is the one of the process by which pipe is manufactured.... if you are asking for this, please reply we will discuss... thank you.
@cck0728
@cck0728 6 жыл бұрын
@@PipingMantra Thanks for your prompt reply. Sorry for the inconvenience. I didn't mean "rolling" while manufacturing of pipes. Also, this question is not related to any of your video. Rather I should have asked, in isometric drawings; piping rolling is given (if required). Why to roll the pipe? Is there any code for rolling the pipe? Is there any effect on process due to this rolling? Thanking you for sparing your valuable time.
@PipingMantra
@PipingMantra 6 жыл бұрын
@@cck0728 ohkay... rolling is just that you are using elbows (90 or 45 in piping ) have the same effect (pressure drop, i think you remember K factor). Rolling normally used when we can't provide std elbows (90 or 45) in confined space. As per my knowledge there is no such std available for that but yes rolling have an effect on fabrication, need to machined (cut, end preparation, grind etc) elbow at shop or site according to angle mentioned in isometric #ideally .
@cck0728
@cck0728 6 жыл бұрын
@@PipingMantra Thanks for your prompt reply. Please keep on contributing with your valuable expertise.
@Yjdjdjfjfjc
@Yjdjdjfjfjc 2 жыл бұрын
Buenos días, saludos desde México, estoy interesado en tomar un curso relacionado al mundo de las tuberías, me puedes dar información por favor
@gulfjob369
@gulfjob369 3 жыл бұрын
Make your narration speed less
@PipingMantra
@PipingMantra 3 жыл бұрын
You can lower the speed of video.. We want our video to have max information in short duration
Tuna 🍣 ​⁠@patrickzeinali ​⁠@ChefRush
00:48
albert_cancook
Рет қаралды 148 МЛН
REAL or FAKE? #beatbox #tiktok
01:03
BeatboxJCOP
Рет қаралды 18 МЛН
So Cute 🥰 who is better?
00:15
dednahype
Рет қаралды 19 МЛН
Shell and tube heat Exchanger maintenance-leak test methods-4
10:14
Technical Engineering School
Рет қаралды 68 М.
How Shell and Tube Heat Exchangers Work (Engineering)
15:13
saVRee
Рет қаралды 1,5 МЛН
Understanding Thermal Radiation
17:33
The Efficient Engineer
Рет қаралды 302 М.
Shell and Tube Heat Exchanger | Floating Head Type | Oil & Gas
3:56
Technical Piping
Рет қаралды 103 М.
Heat Exchangers types(Classifications), Selection of Heat Exchangers
21:53
Concept Connect (Chintan Modi)
Рет қаралды 4,7 М.
PIPING FITTINGS | PIPING MANTRA |
15:09
Piping Mantra
Рет қаралды 31 М.
Tuna 🍣 ​⁠@patrickzeinali ​⁠@ChefRush
00:48
albert_cancook
Рет қаралды 148 МЛН