Heavy Flywheel Pulse Motor

[@rexgeorg7324]

Imagine the energy of a ten ton flywheel

[@strangescience3414]

I do similar stuff on my channel

[@RavindraSDhande]

Thank you very much for this video it saved my time. i wanted to try this on a heavy flywheel. thank you so much.

[@strangescience3414]

Looking for axle 001 page. Is he using a capacitor or what???

[@valveman12]

If you looked on a Scope, this voltage you see is actually a pulse and not a steady voltage like DC. You are correct in your assumption that you are getting BEMF from the coil collapsing. If you let this run on a battery, it would eventually stop because in fact you are not charging the battery. If you measure the average value of the voltage you see on the meter, it would be less than the value of the battery and therefore what looks like you are charging the battery, you are actually depleting it at a very slow rate.

[@NovaJackson]

+valveman12 If you took all the pulses that are far larger than the battery voltage and leveled them out using a capacitor and a choke you could end up with a steady dc voltage greater than the battery voltage.

[@valveman12]

+Jackson Steen As soon as you put a load on it, your voltage will go way down. Your voltage pulse output will be a function of the amount of current you are drawing. An Oscilloscope will verify this. There will always be a loss. You will never get Overunity or anywhere near it.

[@DS-ol2dv]

KZbin is so ripe with shills, it's exhausting.

[@boboclown7875]

yes!!!! this can do overunity. it's perfect. the heavy flywheel acts as a motor itself. you can get away with sticky magnet issues. great job great thinking sir. nice video.

[@valveman12]

+Bobo Clown No it can't do Overunity. Nothing can because everything has loss.

[@MistLostWinder]

+valveman12 that's a good response if you want to limit the possibilities. even if overunity is impossible, its still nice to see something that can take very little and still go a long way. I mean if we all had your thinking we wouldn't go after solar energy or invent hybrid cars. efficiency is the goal.

[@valveman12]

AGENT G Really! If you had my thinking? what do you know about my thinking and my Education based on one comment? Maybe it's your lack of understanding but I don't know that because I don't know your background.

[@MistLostWinder]

+valveman12 I don't care about your education. its obviously something that limits your knowledge and input. If you didn't hear it from a textbook or a professor, you shut it out. Do you think Heisenberg gave a shit about what Einstein had to say? or Tesla gave a shit about what Edison had to say about the limitations of physics and what we think we know? laws are broken all the time. What do the laws of physics say about the probability of a planet like earth existing? yet here we are. If perpetual motion is impossible its only because we haven't learned how to create it yet. in the 1920s, television was science fiction, yet a guy from a small town invented one. don't you think that says a whole lot about educated people? its always the run of the mill people from colleges who go around telling dreamers that everything is impossible. If this guy had a PhD you would not be telling him his ideas are useless.

[@valveman12]

AGENT G Physic Laws are broken all the time? When? It's not like a traffic Law. These are Laws that govern how our Universe works. Man didn't make up these Laws, they were there for use to discover. BTW: Tesla and all the other people you mentioned followed those Laws of Physics that you claim can be broken. Get your facts straight. You go ahead and make your Perpetual Motion Machine. Good luck with that.

[@captainmarkgray8856]

Use a diode to keep the juice from running backwards (running in one direction only = into the battery). Research wind generator diodes for a starter.

[@balloutyves]

Bonjour, ou peut on trouvé le schéma électrique, de ce moteur a impulsions ? MERCI

[@pksharmakolkata]

Hello what is the link to Axel0001's video ?

[@nikson1520]

Please horizontal or vertical Wheel have = work ? ???

[@edgarrapisora2712]

Could you send electric circuit parameter? Thanks

[@mohitable12345]

how much power (watts or amperes) does it consumed? and how was the weight of the metal disk?

[@TrustingJesus67]

I like what you did. I'm going to do the samething this fri. 7/1/11 when my reed switches come in. I have a heavycart wheel and 10 magnets I'm going to hopefully make fly around.

[@christopherpowers7736]

I am not sure I agree with your comment. The bemf on a pulse motor is easily collected and stored or put back in the driver. Usually this can add 20-30% efficiency.

[@philiptimber7977]

Do you sell the machine ?

[@professorfidelcat]

wow the flywheel is heavy and it still spins, even 290 rpm is good enough to add additional coils to tap more out put from the system to charge another battery like a bedini..

[@GG-od2tr]

Nice work.

[@upmperthay]

You could put a ring with a lid it to reduce the wind resistance. :-)

[@Zodliness]

In a rudimentary capacity this crudely constructed device touches upon John Bedini's Monopole 'Big Boy' generator.

[@jccooluser]

Try with the EZ spin circuit and what type if bearings are you using

[@NovaJackson]

Jose Cardona I used the original bearing that came with the flywheel from any car.

[@Gadgetmall]

what if we add 20 magnets in a alternating config on the bottom n s n s etc then a very lage coil or several coils and generate power with out cores i n the coils for a no cog output. i bet you can rectify that power and loop it back to the source.. this coukd onky work becuse you have the advantage of gravity assisted wheel u like a lightwwight one that would stop quick. im working on just that with an 80pound hit miss flywheel

[@balloutyves]

Je cherche le schéma mais rien,dommage.

[@McDonalds_vesh]

is that sling blade

[@EnsyongTv]

And so it is a kinetik force acting on a flywheel.. In my openion, it depends on howmuch force you applies on the flywheel, same output it will apply back on... 😅

[@fearbabyriffs]

Thank you for video. Can anyone tell me how to attach a homemade aluminum disk (flywheel?) to a bicycle axle (bolt)?

[@whiskey2446]

That's awesome great work think you can email me the schematics, I would like to try to build one, thanks

[@NovaJackson]

UNUBIS 3049 Hi UNIBUS; Just see the reply below to "delphinny"

[@kuyanatnatdkrx7]

combine that with NASA's levitating magnetic flywheel and you get a flywheel that has only has theoretically zero friction only taking air resistance into account which means its a flywheel that doesn't decrease in energy due to losses.

[@hiranthachamara1762]

I'm from Sri Lanka, good luck,,

[@delphinny]

do you have the schematics? thanks

[@NovaJackson]

***** The electric circuit is simple. Just run the dc in a series circuit through the reed switch then through the coil and back to the other battery post. The coil is just a couple of hundred turns of enameled wire and the core of the coil is made of a bunch of soft steel wire cut to length and glued inside the plastic spool. You could just order a spool of transformer wire and use as it comes on the plastic spool and fill the empty core with the soft iron wire. I made my own reed switch from a simple contact switch (from dead vcr) and glued a tiny magnet on the long arm with the north facing out to repel from the magnets on the flywheel causing the reed switch to close and open with each pass of the magnets.

[@kamrankhankami7793]

Isn't it produce enough energy to make the system perpetual?

[@chronus9083]

no, dumbass. no such thing as free energy or perpetual motion

[@davidedgar7338]

i need a flywheel rig on my bike.

[@corrythew]

And it dos what besides spin ? ...I think I'm missing the point , sorry

[@professorfidelcat]

it uses little energy and doesn't consume like a conventional dc motor, if you can add more coils around the perimeter, you can tap additional energy from the moving magnets to produce more energy like an alternator to recharge another battery perhaps..the axis of the spinning wheel can also be used to propel a fan

[@NovaJackson]

corrythew The video is simply to demonstrate a simple construction of a basic pulse motor. The kinetic energy stored in the flywheel could be harnessed by v-belt to a small dc motor acting as a dc generator or whatever.

[@NovaJackson]

professorfidelcat Hi Prof; The additional coils on the perimeter would cause too much drag which would slow the flywheel down. Better to take the power off the smallest diameter of the flywheel via v-belt then to a small generator. The output of which could be fed back to the battery and thus perpetual motion?

[@dapskool1573]

valveman12 said it all.

[@vincentrobinette1507]

Now, shut it off, move the solenoid and reed switch away, and let's see how long it takes, for the flywheel to coast to a stop!

[@HistoryEmpire2.0]

Good job

[@rexgeorg7324]

the flywheel will reach weightless ness at a certain rpm

[@davidedgar7338]

interesting. i suspected this. almost like centripital orbit.

[@edsonfernandes4997]

free energy

[@65bug519]

back emf from the collapsing field is how ignition coils on engines work nothing new about it

[@MrKurtt76]

My name Kurt tech I want to ask you I want to build one like you can I have diagram all part to build it?

[@mattmoreira210]

You could add more coils. ;)

[@NovaJackson]

+Matheus Moreira The problem this would pose in this very crude experiment is that the mechanical reed switch I used cannot operate or switch on and off fast enough. The reed switch is the limiting factor. The reed switch could be replaced with a magnetic sensor whose pulse would then be fed to a heavy current switching transistor to deliver the pulses.

[@mattmoreira210]

+Jackson Steen indeed. A Hall-Effect sensor, or even some feedback coils would make it. ;)

[@isaacsrandomvideos667]

Cool

[@lando8398]

Check k out bedini ssg. You'll get plenty of energy from your back emf

[@nunu4555]

lookz awsum =) iv been dreaming tuwardz suhmthin liyk this, but this werkz awsum =)

[@aralanmaniyar1007]

nu nu d

[@aralanmaniyar1007]

nu nu f

[@aralanmaniyar1007]

K

[@operarioanderson7981]

John Bedini.. :)

[@winstongrundy7289]

Nice job.lets talk

[@jansolovsky6298]

Pokus pro školáky , prakticky není k ničemu.

[@mohabathaghnejad7555]

free energy haghnejad