Herocut hc8000, myplasm, plasma cnc

[@DazFab]

Nice job on the machine. im trying to build my own cnc also using myplasm..it looks a great software.

[@CncWoodMetal]

take myplasm is a very intuitive, simple software. I recommend

[@DazFab]

@@CncWoodMetal thanks

[@michel54000]

Good morning I would like to buy it can you tell me what tension did you take I want to buy a 220V but I'm afraid I don't have enough tension at home I have a maximum voltage of 40a is this quite sufficient Thank you for all your info

[@CncWoodMetal]

Mialem 230V. Zmienilem na 400. 230 potrzebuje bardzo duzych przekrój przewodow i duzych bezpiecznikow.

[@michel54000]

Thank you for your answer another question Remember which wire section (mm2) and fuse amprerage? And thank you for your answers.@@CncWoodMetal

[@PaweWWnukuLaboratory]

Przydały by się jakieś zgarniacze przed łożyskami, konstrukcja super!

[@CncWoodMetal]

Masz racje;) przydały by sie jakies szczotki

[@michel54000]

EN 220v Thank you for your answer another question Remember which wire section (mm2) and fuse amprerage? And thank you for your answers

[@CncWoodMetal]

2,5mm2 oraz 16A

[@michel54000]

Good morning, Thank you very much for your answer it will allow me to be able to buy this position. with your info I know that I can use it in my garage my electric installation will suffice for the power. All my power sources are equipped in 2.5mm2 with 20A circuit breakers. In addition I will take this one but knowing that I will use it that 50% of its capacity. You have a nice machine congratulations for work. Michel@@CncWoodMetal

[@HerisonCamposmota]

To use it on the CNC, did you need to make any adaptations to this plasma source? Hi, the way you bought it, you can use it just by making calls.

[@CncWoodMetal]

is ready to use after purchase. The plasma has connectors for voltage measurement, plasma start and plasma supply

[@N0b0dy24]

Kinda late but what plug it uses

[@CncWoodMetal]

What plug it uses??? J understsnd

[@N0b0dy24]

@@CncWoodMetal wall outlet plugs

[@CncWoodMetal]

what plugs are you talking about? the ones at the control box?? or the one at the plasma source??? or maybe you're talking about other plugs?? do you want me to give you the trade name of the plugs??

[@wearetherandombros7782]

Hello that cut looks amazing, i am using a cheap non pilot hf plasma and its killing my board. Do you have any interference issues with this plasma ? I am considering buing one asap. Thanks in advance

[@CncWoodMetal]

I have no problems. cuts very well.

[@antreasioannou3535]

hello again sir, i got one and its pretty good. i only have 2 problems and i cant find a solution. what distance do you use from the nozzle to the metal ??? and what kerf width did you use in the software?@@CncWoodMetal

[@tomcio2]

Czy os Z jest z regulacją wysokosci podczas cięcia ?

[@CncWoodMetal]

Tak. Za to odpowiada sterownik thc

[@MetalicznyTom]

Piękna maszyna💪tu widzę masz po jednym łożysku na wózkach a w projekcie twoim są dwa.Ktora opcja jest lepsza?

[@CncWoodMetal]

Dwa lozyska

[@mich7931]

Hey, how is Herocut - did You have any problems with it? On last film I saw You still have it and by tear on torch cable I assume it worked more than few hours, right?😀 I'm thinking of 230V HC7000 +hand torch because it is priced

[@CncWoodMetal]

I didn't have any problems. I recommend 400V. such a current from one phase. you will need to have a strong installation

[@Shernomorskiy_baniy_shan]

Приветствую !!! Я так понял с пневмоподжигом? Как она стоит брать?

[@Shernomorskiy_baniy_shan]

Какой метал по толщине берет без проблем?

[@CncWoodMetal]

Yes

[@CncWoodMetal]

20mm

[@SuperEvgen1986]

​​@@CncWoodMetal20мм на пробитие берет или от края? Спасибо

[@CncWoodMetal]

@@SuperEvgen1986 ja cialem 16mm od wewnatrz. ale 20mm według specygikacji tez daje rade.

[@Koordiant]

Пневмоподжиг ?

[@CncWoodMetal]

Tak

[@matevz4]

Hi. I just purchased HC8000 cutter. Does the cooling fan starts to spin when you turn on the device or it spins only if needed? You made a nice CNC and I hope it serves you well 💪

[@CncWoodMetal]

Wentylator kreci sie w razie potrzeby. Ale u mnie po 1 minucie ciecia sie włącza. Po skończonym cięciu jest załączony okolo 3-5 minut

[@matevz4]

@@CncWoodMetal ok, thank for the answer

[@matevz4]

@@CncWoodMetal thank you