HG Tx & Rx Pairing / Binding

[@البروالمطر]

The 3 pos switchs on this transmitter is working great on flysky transmitter. Just plug and play..

[@jamestennant-eyles9870]

Hello Pradeep, just to say I tried my HG P602 with the tx from my HG P408 and the 602 now works fine. So it's definitely the tx that’s at fault. I got a refund from Banggood of £150 because of all the issues with the 602, so that would easily cover the cost of a new tx. However I may not bother and just use the on tx for both vehicles. I took the back off the tx but could see any obvious issues,so I’ll keep it for spares. Did you find out if the 16ch tx will operate an 8 channel rx? Best wishes, James.

[@3dhub51]

A very important question, can this controller and RX be used for drone and fpv ? Like darwin fpv. Please help

[@pradeepkumarts999]

Sorry for very late reply, Answer is No. Because the throttles are forward and reverse function one but for FPV's we need only increase or decrease and moreover it have very few adjustments for Drones and FPV'd. For you economical one is Flysky or there are lot of other brands for FPV.

[@petersaunders6947]

Hi Pradeep I bought a HG802 from cross rc and it arrived 5 days ago, everything was going good and then the controls went nuts, going forward for a bit and then going full speed reverse, steering was erratic and the tipping function is very jerky. Do you think it could be the receiver or the transmiter, they both have full batteries and will not bind

[@jamestennant-eyles9870]

Hello Pradeep, Your video is helpful, thank you. I have just purchased a HG P 602 six wheel truck. I have discovered that the tx and rx bind as you explain, with a steady light. After binding if I take the tx more than 3 mt from the rx the tx unwinds the rx light blinks. Can you suggest any solution to this? Is the problem likely to be the tx or the rx? I also have P 408 which works with no problem. Can I use the tx and rx from the P 408 in the P 602, in turn, to find out whether it is the tx or the rx that is at fault. Thank you for your help. James.

[@pradeepkumarts999]

Hi James. Hopefully it should bind if it belongs to came brand but sometimes, it will not work as the circuit and frequency will be different. I do not have these models or those Tx & Rx to experiment and help you. My suggestions: 1. In 602 its meaning of Unwinds means unbind I hope and I am suggesting based on this. a. I feel the issue is because of cut or loose connection in Antenna in either Rx or Tx. The reason I am saying as “antenna” is its unbinding after certain range. b. There can also be loose connection in battery / Antenna / internal circuit or antenna of either Tx or Rx would have been cut in transit. This needs to be inspected and corrected. c. If you are still not able to find the fault, or any burns in the internal circuit then it will be an IC problem and you will have to experiment by replacing any one first. d. Ex: replace receiver and check if it works if not next will be Tx. I suggest if any of your friends have same model check with that Tx & Rx so we can find the fault is in Tx or Rx. e. For experiment, try binding the Tx with 602 & 408, there is no harm. Either it will bind or not bind. Binding process will not cause you any issues. 2. In my 802 experiment, I observed the 8 channel Tx was not binding to 16 channel Rx. Generally, I have observed HG and Huina Rx has issue. Lot of my Rx’s stopped working abruptly for no reason. Then I went on to cost effective and good range set of Flysky.

[@jamestennant-eyles9870]

Hello Pradeep, Thank you for your reply. As this is a brand new car, only just received, so I have submitted an enquiry to Banggood. I will wait to see what they will offer. If they do not offer a satisfactory solution I will try the ideas you have so kindly suggested in your message. Best wishes to you, James.

[@pradeepkumarts999]

@@jamestennant-eyles9870 Definitely they will help, i have received good support from them and like u i too had so many issues from Bangood. sometimes i feel they sell damaged product and their packing is not good like Aliexpress or Wish.

[@jamestennant-eyles9870]

Hello Pradeep, I have heard from Banggood and they have offered me £150 refund, which will enable me to purchase a new receiver and transmitter and other parts if necessary, so I am satisfied with their response. I like taking things apart to repair them and this gives me a good excuse to do so! Normally I only buy self build kits. I have bought quite a lot of things from Banggood, about 60 things over the last two years, trucks, planes, model engines, and many upgrade parts. Generally I have found the quality has been very good, but I agree their packaging is sometimes not good. I have never bought anyth8ng from Wish. Have you found them a reliable company?

[@pradeepkumarts999]

Yes

[@jamestennant-eyles9870]

Hello again Pradeep, I understand you cannot pair a 16 ch rx with an 8 channel tx, but can you pair an 8 ch rx with a 16 channel tx? Best wishes for New Year. James.

[@pradeepkumarts999]

I have not tried it, I will try and confirm over this weekend. Hopefully it should get paired.

[@pradeepkumarts999]

Hi James, I tried few methods and it did not pair ( 16ch Tx with 8ch Rx).

[@jlast450]

@@pradeepkumarts999 So you can't pair the 8 ch receiver with the 16c TX?

[@pradeepkumarts999]

@@jlast450 No, it did not work for me

[@jlast450]

@@pradeepkumarts999Thats weird. Normally with other brad receivers they are compatible with different model same brand radios

[@geoffreymaggi1010]

From where can I buy a Trasped 8c radio receiver please ?

[@pradeepkumarts999]

From Bangood or AliExpress, both are good. I recommend for AliExpress.

[@geoffreymaggi1010]

@@pradeepkumarts999 Thank you so much ..

[@khelifihebbache8032]

Hi, thank you for this nice vidéo, i want to bye this radio, but befor that i beye it tell me if it is nice, if it is a nice quality....( I need it for my robot)

[@ThuatBui]

Hello Pradeep, does 16ch compatible with crane P803 ?

[@pradeepkumarts999]

Yes, but if u have TX model of YK002. If your TX is YK003 model it will not support other than 8 channel receiver.

[@ThuatBui]

@@pradeepkumarts999 I have YK002 and 16ch rx. It seems not working with the crane P803. At least from the user manual, they said "compatible with YK003" and didn't mention YK002.

[@pradeepkumarts999]

@@ThuatBui Did you follow the binding method i have shown particularly for YK002? The binding method for 002 & 003 is different. Pls share the video of Tx, Rx and the process you are following if issue persist.

[@ThuatBui]

Hi @@pradeepkumarts999 , it's not about pairing/binding the YK002. I was able to do that with YK002 and control the truck, but only not the crane P803. While YK003, I can control the truck and the crane. I guess the question is if YK002 compatible with the crane P803

[@pradeepkumarts999]

@@ThuatBui can you pls share photo's of receiver and transmittor to [e-mail] or upload video.