High Voltage Break In 【ミニ四駆】Tamiya Mini 4WD #63

[@benson556]

I just did this on my Hyper Dash 3 from 26k to 29k. This was easy and fast. Do you think there is any negatives to this method? Like shorten motor life?

[@roscoechannel]

it won't significantly shorten your motor life, but you need to maintain the motor condition (clean - lubricate, etc). The motor life will also depend on how frequent you use the motor.

[@benson556]

Does this method work till this day? or is there any other new updated methods?

[@roscoechannel]

I still use this method.

[@zayyandzikraka3833]

bang.. sampe sekarang abang masih pake methode break in seperti ini..? atau udah ada methode lain yg lebih bagus.. sebab tiap saya liat mobilan abang lajunya kenceng bener.. 👍👍

[@mtz3808]

Hyper dash jcup series and standard series any difference?

[@roscoechannel]

Some says there is a difference. But I didn't do any comparison between them. So I can't say the exact difference between them.

[@h4735w0rn]

Luar biasa, setelah di breakin motornya, bersinar kaya di animenya dash yonkuro om

[@roscoechannel]

Omaigattttt

[@kuyanchannel181]

Mau tanya, untuk proses ke3 nya kenapa menggunakan Voltase 3.5v dengan durasi 3 menit ya?

[@roscoechannel]

Dulu sih diajarin sm guru saya, ktanya sesi itu untuk menstabilkan rotasinya. Wlopun pny saya ga stabil2... 🤣

[@dinan_dino]

@@roscoechannel wah bener bngt ini.. barusan saya coba di mach dash, pas masuk di tahap 3.5v rotasinya jadi stabil banget.. sedangkan wktu di 6v ga stabil rotasinya

[@roscoechannel]

Mantap jiwa

[@CebuTams]

Whats yhe name of the app rpm checker?

[@roscoechannel]

giri

[@krel4115]

hello i am from the Philippines.. I am a beginner in Tamiya mini 4wd racing.. i just want to ask what is a TMAC build set up and the BMAX build set up.. what are the differences between TMAC and BMAX set up... what aree the race rules for these set ups? can you make a video about the TMAC and BMAX set ups?

[@roscoechannel]

I'm not familiar with the TMAC rules. I guess it's better to ask the racer around your area to get an accurate information regarding the rules and machine setup.

[@krel4115]

@@roscoechannel how about the BMAX build? is there a BMAX race category that is only for machines that uses tuned motors?

[@HDAD419]

Hi sir Roscoe, did you modify your battery discharger to have a volt meter in it, or did it already have a volt meter when you purchased it? As far as I can remember tamiya dischargers doesn't have a volt meter built into it.

[@roscoechannel]

Yes. A friend of mine modified it. I don't even know how to make one. 😅

[@HDAD419]

@@roscoechannel aww it would be nice if your friend made a tutorial of how to make it. Anyways I'll guess I'll try to figure out how to make one or maybe call a friend that knows how to make one. On a side note thanks for the reply, looking forward to your next upload! More powers to you sir!

[@risnamulyono5865]

Bang,klo ciri fisik batre yg bagus... Yg sudah d brek in seperti apa? 🙏

[@roscoechannel]

Nggak pernah buat perbandingan, jadi nggak paham juga bedanya.

[@itzmee57]

Om kalo break in motor mach dash pro emang gimana? Apakah setiap break in dengan dinamo berbeda selalu ada cara nya tersendiri2 ?

[@hendowinata5054]

Om dosen mau tanya klu hyper dash pro biasa sama hyper dash japan cap 2020, beda ato sama sih rpm nya? Yg standard baru di buka dr baru nya

[@roscoechannel]

belum pernah bandingin nih

[@tnk9254]

Thank you for adding Japanese subtitles

[@roscoechannel]

You're welcome! 😁

[@alexanderluh9678]

Can i do a low voltage breakin then gradually step it up to high voltage?

[@roscoechannel]

Yes you can. There are various method of motor break-in. I'm used to this method cause it produce a motor that suits my playing style.

[@reinhardsasauw6536]

Brader.. Untuk Mabuchi apakah sama perlakuannya pake high voltage juga? Thank you

[@roscoechannel]

Betul

[@asruladli0541]

Mas... Kalo permulaan mau breaking kne pake batri low or full charge batri... Mas

[@roscoechannel]

For me, I prefer large voltage. I felt bigger torque in my motor.

[@cedricjacinto5777]

If its okay to break in again the motor, if they had already break in?

[@roscoechannel]

If you feel that the previous break in was insuficient, then I think you can do it again. Though I'm not sure about the effect for the 2nd break in...

[@rooseno]

what if you do the backward rotation first in every step of the break in process?

[@roscoechannel]

I never tried that method before

[@akbararya7243]

Bang, saya kan ga punya alat breakin motor. Kalo misal 4 baterai 1,5v saya seri, kan jadi 6v, terus saya sambungin ke motornya bakal sama aja nggak ya?

[@roscoechannel]

Bisa kok

[@anakkostan5368]

Saya masih bingung sih, tapi misalkan tidak di break-in apakah ada pengaruhnya sama lari mobil? Untuk break-in ini seperti inreyen di motor yah? Untuk test-run itu dimana?

[@roscoechannel]

Pengaruh dengan lari mobil pasti om Kalo inreyen motor saya gak paham om. Test run di graha tamiya bsd

[@anakkostan5368]

makasih infonya, semoga bisa selalu berbagi teknikal di dunia mini4wd

[@roscoechannel]

Sama2 om. Terima kasih sudah menyaksikan. Semoga bermanfaat 😊

[@AkbarGobz28]

Bisa dibilang bgtu Bang @PraztDR..break in dinamo, hampir sma kaya reyen motor/mobil yg abis ganti seher/piston..

[@warawiriwara]

om untuk break ini, contak clener diganti pakai wd40 apa bisa?

[@roscoechannel]

Nggak bs bro

[@centralproperty-mi8ie]

Kalau machdas pro apakah voltasenya sama? Itu alat breakin apa namany ya om roschoe?

[@roscoechannel]

G force mini break in system. Boleh dicoba

[@centralproperty-mi8ie]

@@roscoechannel siap om roschoe. om kok jarang bikin video lagi.? Padahal selalu di tunggu video2nya.

[@ragamdestinasi]

Break in diperbolehkan turnamen kah????

[@roscoechannel]

Boleh. Yang gak boleh dicoak. Tapi di Indonesia semua boleh kok. 😆

[@arielnezayoslin5998]

Bang, apakah harus brand new motor? Saya baru beli hyper dash pro blom di break in tp sudah di pakai, kalau saya break in setelah dipakai apakah masih ngaruh bang?

[@roscoechannel]

Sebaiknya break in sebelum dipakai jalan sama sekali

[@siwasmojokertokota2651]

kak roscoe untuk adaptor yang kakak pake di gforce nya itu pake adaptor apa kak

[@roscoechannel]

Adaptor sesuai angka di alatnya itu gan. Lupa angka outputnya. Tapi djual kok di toko2 online

[@Callme_Den]

Beli break-in sytemnya dimana bro

[@karismaprawinata5945]

sudah dapat info nya belum bro

[@roscoechannel]

Coba cej di toko online deh gan

[@karismaprawinata5945]

@@roscoechannel makasih gan info nya dan tutorial nya

[@yudhadwi1043]

Master, kalo murid pake nya wd40 boleh?

[@roscoechannel]

Jangan euy. Rusak nanti dinamonya

[@yudhadwi1043]

@@roscoechannel untung murid keburu tanya. Cuma punya WD soalnya. Hahaha Murid pernah denger yg di celup ke air gitu di break in nya master. Itu emang bener? Maaf banyak tanya ya master, murid newbie di dunia per 4wdan.

[@roncabais4362]

the best break in for engine is at no contact of power current. then clean process.. then put it the motor for break-in status in between two powerful motor like 2 plasma or ultra then the next day motor for break-in run for a power current for 1 hr standard battery then take rest for the motor for an hr. then run the motor backwards. rest for an hr again. then clean.

[@roscoechannel]

Thx for the info. What's the reason for waiting until the next day?

[@roncabais4362]

actually its really like the concept of break-in an actual engine. you will give a resting process. it depends on your taste if an hr, a few hrs or a day of a rest.. just count succedingly according to the counting process.. there is also a runtime on how many hours so that it will giveout the full potential of the new motor til last

[@roncabais4362]

just give a try. we do that here in Phils at Plasma and Ultra dash motor for open circuit events

[@roscoechannel]

I see 👍 Thank u

[@roncabais4362]

kzbin.info/www/bejne/q6W8eomvd9BmqMU Here watch this event Ultra dash vs Plasma dash FULL TAMIYA SETUP no rewind no stir.

[@ericalvarez6263]

What specific app do you use on RPM meter?

[@roscoechannel]

Giri rpm checker

[@rizalboyani]

Bang mau nanya brp ya voltase yg bagus untuk break-in dinamo ?

[@roscoechannel]

Nah itu ada dijelasin d video

[@deddyazwar8641]

Om 1 mesin maksimalnya berapa kali di break in...???

[@roscoechannel]

1x saja

[@deddyazwar8641]

Thnks om

[@hendriknikijuluw1352]

Om bikin tutor velg shaft tembus dong

[@hattahadiputra6873]

Beli alat break in dmn mas?

[@roscoechannel]

Di toko online ada kok

[@albaihaqi2817]

Pemula kaya saya lihat kaya gitu bingung om,alatnya namanya apa jg ga tau di kota saya ada apa ngga jg saya ngga tau.wkwkwk Berapaan om alat break'in sama pengukur voltase baterai?

[@roscoechannel]

G-force mini break in system

[@albaihaqi2817]

Berarti kalo motor baru harus di break in dulu ya banh?

[@roscoechannel]

Betul sekale

[@albaihaqi2817]

Harus punya alat break'in sama yg buat cek voltase baterai jg brrti. Di kota saya belum pernah lihat alat kaya gitu bang.

[@roscoechannel]

Coba aja order di toko online. Kayanya uda banyak yg jual

[@Kiko-oj2jj]

What app did you use for the rpm

[@roscoechannel]

I think I've mentioned it in the video

[@Kiko-oj2jj]

@@roscoechannel thanks but I didn't heard it can you pls tell it

[@roscoechannel]

Giri

[@muhammadfatihazhar8470]

Gan mau nanya kalo gear buat ms bisa tidak dipakai di ma

[@roscoechannel]

Bisa gan. Gear untuk MS dan MA sama kok.

[@muhammadfatihazhar8470]

Roscoe Channel terima kasih Gan atas infonya

[@AxavierTamiya]

Pake aplikasi apa itu om?

[@roscoechannel]

Giri RPM checker gan namanya

[@irwantea90]

Bang sambungan colokan nya pake apaan?yg buat kelistrik ny

[@roscoechannel]

Pake adaptor

[@yordankuz]

kmaren liat agan main di tamiya JT, apa semua motor agan di break in makanya bs kenceng gt?

[@roscoechannel]

Betul sekali gan. Semua motor sebaiknya di break in agar performanya prima

[@yulianitahaniastuti7796]

Buat stb boleh bang?

[@roscoechannel]

Boleh aja tgantung motor apa yg diijinkan

[@securetoastcheese3959]

omg, new intro :D

[@alexandradeguzman8193]

can i ask if what app did u used for getting the rpm

[@roscoechannel]

The name is Giri RPM checker

[@budisetiawan3930]

Bang,beli adaptor nya Gforce nya dimana ya ?

[@roscoechannel]

Tokopedia ada gan

[@budisetiawan3930]

Merk nya apa mas ?

[@roscoechannel]

Baru saja saya cek, nggak ada merk nya gan. Disesuaikan saja dengan outputnya G-force.

[@budisetiawan3930]

Ok mas trima kasih info nya 😊

[@christchen3153]

Kalau menurut saya 5v kyknya kegedean deh om, kasian mesinnya...:) Saya pake breakin 2.8-3v dpt rpm 31rb...:)

[@roscoechannel]

Judulnya eksperimen om. Hehe. Mgkn tgantung voltase batre, saya ngetesnya di 2.85v kan rpmnya.

[@VitoChad]

Itu kok di kasih tape tamiya

[@dccuttingsticker6745]

Yg saya tau Dinamo gk boleh d bukan tp boleh d coak walau gk semua regulasi sama bg kalo boleh saran break in ala speed dengan membuat garis leher angkur pke pincet segaris Lena mampaatin lubang coak dinamo he he agak ribet penjelasan saya sory bg he

[@roscoechannel]

Peraturan resmi Tamiya Mini 4WD nggak boleh sama sekali. Bisa dibaca di Official Rules Tamiya Mini 4WD. 😎 Coak, dibuka, dicongkel, diintip leher angkur atau leher ayam (lho kok ayam?) nggak ada ceritanya dimodifikasi kalo berdasarkan rules resmi Tamiya. Kalo peraturan toko2 ya dibebasin aja tergantung tokonya.👌🤣

[@rifqifarisazzaki3657]

150k ya?

[@roscoechannel]

?

[@VitoChad]

Jelasin fungsinya ok

[@deniashar8686]

gan subtitle indonesianya di ksh dongg

[@roscoechannel]

Yes gan, menyusul ya. Maaf soalnya belum ada media buat edit subtitlenya. Nanti pasti dimunculkan gan. Harap maklum.

[@deniashar8686]

oia mau nnya gan klw casan HiTEC AA/AAA CHARGER X4 bsa di pake power bank ngecharge nya?

[@roscoechannel]

Gak pernah pakai gan. Jadi gak bisa kasih jawaban. Saya hanya pakai Powerex.

[@roscoechannel]

Subtitle Indonesianya sudah tersedia ya. Untuk video Motor Basic Knowledge juga sudah tersedia. Monggo ditonton + diserbaluaskan. Terima kasih gan.

[@deniashar8686]

gan alat yg ijo namanya apa trus fungsinya buat apa aja gan

[@spacezone2216]

Kedua

[@kiflialhadar5315]

Oppo

[@MrFilthyfingers]

Boss why is it you break in to only 27k plus rpm instead of those doing 38k rpm.. Any reasons ? And if so will you share of how to break in till 38k using dis device? Thank you!

[@roscoechannel]

Wow, HDP 38rpm? Well, actually the RPM displayed will depend on the voltage received by the motor. With 2 batterries, I've never find my HDP reached 38k rpm. But I'm quite satisfied with the motor coz I'm aiming to get a high torque motor rathern than a high rpm motor. So it's fine. 😁

[@desiikasari4923]

Dinamonya kasih tamiya tape biar apa sih bang

[@roscoechannel]

Buat penanda aja

[@temennyakepin3775]

Budayakan bahasa indonesia wk

[@roscoechannel]

Siap! 😆

[@johnkamantigue9893]

First again XD

[@roscoechannel]

Thanks man! Much appreciated! 👍

[@johnkamantigue9893]

Thanks for the tip also!

[@ぴゃんねる幸村]

日本語にしてください

[@roscoechannel]

はい。少々お待ち下さい。字幕を作った後にまたコメントします。

[@roscoechannel]

日本語字幕はすでに利用可能です。

[@RieskyCH]

Ngapain ngomong inggris bang. Budayakan bahasa indonesia