Laminate inkjet or laser printer images and graphics on a guitar using my Z-Poxy technique. Z-Poxy Finishing Resin: amzn.to/2Kany4y
Пікірлер: 169
@WatcherintheRye Жыл бұрын
It's so cute that you 'invented' decoupage 😉
@HighlineGuitars Жыл бұрын
Hey everyone, I pinned the above comment for obvious reasons.
@stevestammet161610 ай бұрын
It's so cute that you liberated "Catcher In The Rye" for your tag. GTFOH hypocrite
@user-sg1qb5go1m3 жыл бұрын
Hello. There are many guitar masters in Russia, but they do not share their skills with others, they are very greedy people. You give knowledge to ordinary people. Great respect to you.
@runningwithscissors09113 жыл бұрын
Well, this is sure easier than all that transfer paper and reverse-the-image stuff. And it looks like the Z-Poxy doesn't alter or dull the colors! Thank you!
@dpajc05629 күн бұрын
AND better result too!
@mayfashguitars Жыл бұрын
Thanks so much for this video😄, you just helped my life, you will not understand😄 my client wants her picture on the guitar, I have been googling how to do that for hours now and I saw your video, been following you but yet to see this one then, thank God I found it now, so excited right now😁
@RaindropServicesNYC6 жыл бұрын
I have to admit, I'm really impressed with all your videos. I automatically give you a thumbs up every time I open one of your videos. Thanks a lot for taking the time to share your ideas.
@Chammoose3 жыл бұрын
You’re the man. Exactly what I was looking for. Thanks a bunch.
@bobroberts72786 жыл бұрын
The results of this method greatly exceed the previous. Very professional result. Great job!
@dpajc05619 күн бұрын
THANKS FOR THIS VIDEO, HOWEVER PLEASE MENTION YOU NEED TO HAVE A WHITE BACKGROUND (White GUITAR) BECAUSE THE PAPER WILL SOAK IN ANY BACKGROUND COLOR OTHERWISE
@chrisbardolph3 жыл бұрын
I've been looking for another way to do fabric top guitars, and I think I'll give the Z Poxy a shot.
@4dmind4 жыл бұрын
Works great on utterly flat surface applications. Does not work well with guitars with rounded outer edges. Also, you may have to experiment with printing technologies, because I had a high end print done as a master and the colors ran under the z-poxy. But I was able to achieve the desired aesthetic via some modifications - 1. I trimmed the graphic to the extent of the flat part of the surface only. 2. I used a black sharpie to blacken the edges of the cut graphic. 3. I sprayed black spray paint at the edges of the graphic to soften the delineation (you could do the same with an airbrush) and then 4. I put the final Z-poxy coat on, followed by Clear Coat / Polish sanding and budding etc.
@causetherat3086 жыл бұрын
if you have pickup covers you could use the cutouts to cover them as well. This is an AWESOME idea.
@spdxlz27172 жыл бұрын
Good good on the list guitar that is really good texter and good a good practice makes perfect
@sonicpickups4 жыл бұрын
I bet Art Resin would work really well for this technique too! Crystal clear and non yellowing. Nice work!
@daveellison88323 жыл бұрын
yeah leaving the paper on the guitar without the reversing image and paper removal DEFINITELY is more up my alley...hate epoxys though...i'm wondering if elmers glue may do me...we'll see...nice work, i'm gonna try this later.
@fishbinky3 жыл бұрын
did you try the elmers glue?
@stevesoldwedel5 жыл бұрын
I think, if I do this, I'll put the part that I cut away from the pickup cavities in the bottom of the cavity, just because.
@T13743 жыл бұрын
Nice. This is the video I needed. Thank you.
@HighlineGuitars3 жыл бұрын
You are so welcome!
@nanaandbump. Жыл бұрын
Cool stuff! Hey just thought I would share something I found recently - I have switched from using xacto to using disposable scalpels for real precision stuff. They are super cheap and quite significantly sharper than xacto blades for some reason. Anywho, just fyi, thanks for all of your cool vids!
@HighlineGuitars Жыл бұрын
Great tip!
@johnnypk19636 жыл бұрын
Dig it. Graphics, fabrics, metals lots of new mediums to use for a fresh look.
@JackbenchWoodworking5 жыл бұрын
I love your channel, Chris
@EmmanuelVassilian27 күн бұрын
does someone get copyright issues by doing this or is it no big deal? thanks! btw it turned out very beautiful, you are the boss Chris! keep up the good work.
@HighlineGuitars26 күн бұрын
Only if you manufacture and sell them.
@vnidk15 жыл бұрын
Great video Chris. If you could, would you print the graphics on one single sheet of paper to avoid possible visible juncture between the pieces?
@Stratolinerator Жыл бұрын
How much prep work do I have to do on the guitar body if I will be doing this on both sides? Should I paint the body with a primer? Must I smooth everything with wood filler first or does the paper smooth the wood out enough. How high of a grit do I need to sand the wood to prepare it for the lamination? What's the best brush-on polyurethane to use for this technique? Sorry to ask so many questions, but this will be my first attempt at a DIY. Thanks
@brianpetersen34296 жыл бұрын
Great tips!
@radsketchpad6 жыл бұрын
Cool experiment, the results look great on both versions you did (mod podge vs. z-poxy). I guess choosing between the two methods would just depend on the style of your art/graphics? Thank you for showing us your technique!
@MrLaurizio5 жыл бұрын
Wow! That Looks amazing!
@burningbastardguitars2 жыл бұрын
I would love to see how you made the image and made sure it would fit the guitar so perfect.
@HighlineGuitars2 жыл бұрын
Uh oh, not you got me thinking about a future project!
@burningbastardguitars2 жыл бұрын
@@HighlineGuitars would really be interested to see it.
@burningbastardguitars2 жыл бұрын
@@HighlineGuitars any chance of this happening?
@eturnxl8372 жыл бұрын
I’d like to see as well
@TheSteelheadStation Жыл бұрын
Did this suggestion ever happen?
@FluidRat5 жыл бұрын
Oh my goooooooooooooooooooooooooooooooooooood, thank you. I have been scouring the internet for the past 3 days trying to find a better method of image transfer than the modge podge. Something about modge podge makes me think that you'll never get crystal clear pictures, and with a project that I'm planning, I need it crisp. One question though. Since this isn't relying on the white filler to give white tint to colors, would it be better for me to paint the body completely for an even coat, laminate and sand (where needed,) /THEN/ apply clear over the body? Thanks
@SkyscraperGuitars6 жыл бұрын
Cool technique.
@gtrman1263 Жыл бұрын
So is that just regular printer paper? And zpoxy doesn't bleed the image at all? That is extremely cool. I haven't seen your other video on this. I'll probably check it out too. But this looks super easy
@pixpusher6 жыл бұрын
Looks great!
@hastyberford6 жыл бұрын
Very cool. Please add on a finished photo when it's all done and put together.
@ashlieghcarboni64892 жыл бұрын
I tried this w/ zpoxy and a guitar. The Abigail guitar, sadly the 90% of the ink faded to white. I guess u need to use a laminator 1st.
@hillip15 ай бұрын
Hello. Great video. Thanks for sharing. If I am doing this with a black guitar , do I need to paint it white before starting
@HighlineGuitars5 ай бұрын
Test on scrap. I don't know if it will work over black. Me thinks it won't.
@bronzesnake70043 жыл бұрын
Looks fantastic! Thank you for the instruction! Jack ~'()'~ Canada Manly!
@shaneh9286 жыл бұрын
Pretty sweet! 👍
@StuntcatTV4 жыл бұрын
Thank you!
@johnewald31485 жыл бұрын
That's supercool!!
@Mooncalf20125 жыл бұрын
There are some affordable 13 x 19 printers on the market now, I found a used HP Photosmart large format photo printer at a local thrift store for $10. Have you also tried iron on print paper or water-slide decal paper? (Both would require reverse printing technique.) I have a need to cover the entire outside surface of a Telecaster with a seamless printout, I may have to create texture maps in a 3D program to accomplish this...
@wheresthepick11 ай бұрын
Helllo buds...i wanted to know whats clear coats..is it those glossy finish ?or
@tonthatlong29325 жыл бұрын
thank you, yea!
@rogerboswell5483 Жыл бұрын
Can I use a picture from a thrift shop to do that to my guitar? I always see cool picture printed on paper on frames.
@pgmaillot8 ай бұрын
Question... How good will the inkjet ink picture look after several years? Isn't it wearing off over time and UV exposure?
@HighlineGuitars8 ай бұрын
It looks as good today as it did when it was made. The inks used are UV resistant.
@BenjaminJohnson6 жыл бұрын
This is super cool! Thanks for sharing. What weight of paper are you using?
@HighlineGuitars6 жыл бұрын
20lbs.
@-Thunder5 жыл бұрын
@@HighlineGuitars Great tutorial! Is there any reason to not use printed vinyl? Especially for an arch top guitar?
@jesusgirarte-sandoval7535 Жыл бұрын
What about the holes for the vol pots or the holes for the bridge? Did you do drill those out afterward?
@HighlineGuitars Жыл бұрын
The holes for the controls were drilled before and the holes for the bridge were drilled after. The control holes don't require absolute precision positioning, but the bridge holes do. For that reason, I waited to drill the bridge holes after the art was laminated and the neck was installed. That way I could line up the bridge with the neck.
@emilzd2 жыл бұрын
Hi. I like your videos. What I'd like to know is the lifespan of colors on the guitar. How long can we hope to have the same quality of colors? Are they going to fade like regular printed photos? Thank you for your answer.
@HighlineGuitars2 жыл бұрын
It will only fade if left out in the sun. Eventually. Who knows how long that would take. However, if you leave a guitar in the sun, you deserve whatever happens to it.
@rugs4free655 Жыл бұрын
With this you started with a body sanded down and smoothed to 220 Grit? Could this be performed on an already painted guitar?
@HighlineGuitars Жыл бұрын
I've never tried it with a pre-painted guitar body.
@Fast4VVard Жыл бұрын
just wondering if this technique would work on vinyl wrap or if there is a way of doing that on a wrap?
@KD88RET5 ай бұрын
When you say nitro gloves, is that the same as nitrile. I've searched for nitro gloves in the UK and all I get is nitrile.
@HighlineGuitars5 ай бұрын
You miss heard what I said. I said nitrile.
@Stratolinerator Жыл бұрын
Do the graphics look better if you use Photo Paper instead of regular paper, or is the Photo Paper too thick? What kind of primer did you use over the unfinished wood?
@HighlineGuitars Жыл бұрын
Photo paper is too thick. I used regular white acrylic paint for a base coat/primer.
@Stratolinerator Жыл бұрын
@@HighlineGuitars thanks thanks
@TheSvartulfr4 жыл бұрын
I wanna see this finished with hardware and a sound sample
@HighlineGuitars4 жыл бұрын
No photos of the finished guitar. It was shipped out before I had a chance to take any. I never record sound samples. There's no point.
@ndn25895 жыл бұрын
Gorgeous
@traceridpath66146 жыл бұрын
When designing your collage of sci-fi images, what software tool did you use? And secondly, how did you get the shape of the guitar body into the software you used to create the collage? It appears the collage making software recognised the boundaries/borders of the guitar shape. Any additional insight is greatly appreciated. Thanks
@HighlineGuitars6 жыл бұрын
Trace Ridpath I used Adobe Illustrator and placed the images in a document large enough for a guitar body and used an outline shape of the body to mask the collage.
@johnpiotrowski31085 жыл бұрын
How about showing the finished guitar????
@kenthefish83862 жыл бұрын
What is the paint u used on the body before you used the z-poxy
@HighlineGuitars2 жыл бұрын
Probably a water-based acrylic from Hobby Lobby.
@TheAirtime235 жыл бұрын
Great idea! How can I print an image to the exact dimensions of my guitar?
@HighlineGuitars5 жыл бұрын
I used an outline I created for the CNC file as a mask for the design and printed it at 100% on multiple sheets.
@musicmaze6403 жыл бұрын
Would this work on a carved top, like a Les Paul? Love your videos, by the way.
@HighlineGuitars3 жыл бұрын
Yup.
@BoudreauGuitars6 жыл бұрын
Cool!
@michaelkennedy21906 жыл бұрын
Looks great! You don't have to worry about the Inc bleeding when you use the z poxy ? I have an Inc jet printer. I guess you need to test on a piece of scrap.
@nonolaporte31956 жыл бұрын
From what I understand, the fact that the z poxy reaches the ink from the back, through the paper, keeps the ink in place. A mistake would be to apply the top coat of z poxy just after applying the paper, because the ink would not be bonded to the poxy yet.
@ThePremixPilot3 жыл бұрын
This Z poxy wont cause any ink runs right? Or bleeding?
@Dreamdancer114 жыл бұрын
Do you think that mixing zpoxy with things like mica powders would be valid for an easy and relatively quick finish?Thanks again for your great content...
@HighlineGuitars4 жыл бұрын
Yes, absolutely. Experiment!
@deltapunk6 жыл бұрын
awesome video, thank you for the tips. what would you use if you wanted the graphics to have that "old "yellow look, like old comics or news papers. Thanks
@HighlineGuitars6 жыл бұрын
I would use Photoshop to mimic the old newsprint look.
@seancraig53455 жыл бұрын
Does the Z Poxy level itself pretty well before it dries and cures?
@nicoleeman22575 жыл бұрын
Z-Poxy is very sensitive to temperature. If you want it to level better you can warm it with a hairdryer (paint stripper). Keep the hairdryer (or paint stripper) one to two foot (30 - 60cm) away from the surface to prevent overheating. The Z-poxy will cure faster and way much harder than at lower temperatures. The down side is that you might blow dust on to the surface with the airflow. Be careful because the Z-Poxy will get very runny when warm/hot and you might blow it over the edges with the airflow! Hot curing will make Z-Poxy glass like hard.
@jaa24123 жыл бұрын
Awesome technique! Can I use wipe on poly as a clear coat over this? Regards
@HighlineGuitars3 жыл бұрын
I'm not sure. The only way to know would be to do some tests to see if it'll work.
@koontzman1236 жыл бұрын
What if my guitar had a binding? Remove and cut the picture in and then reapply binding? Or remove binding and do a round routing on the top. I think it's not possible to leave the binding on and cut the transfer to where the binding edge meets the guitar.
@HighlineGuitars6 жыл бұрын
I would remove the binding, apply the picture, trim it to the edge of the binding channel with a fresh razor blade and reattach the binding.
@koontzman1236 жыл бұрын
@@HighlineGuitars thanks, there had to be a way.
@stephencraig85789 ай бұрын
I keep hearing people talk about napa in their videos. I can't find out what it is online. Could you let me know what it is,please?
@HighlineGuitars9 ай бұрын
Naphtha. It's a solvent.
@stephencraig85789 ай бұрын
I spelled it wrong. You'd think it would still come up in a search. jeeesh! Thx for letting me know. 👍
@terribleligadelmal45413 жыл бұрын
what could be a substitute to Z poxy? in my country they dont sell it and shipping companies dont want to mess with cans and sprays
@HighlineGuitars3 жыл бұрын
Z-Poxy is basically a very thin, slow curing epoxy. Any epoxy with similar properties should work.
@terribleligadelmal45413 жыл бұрын
@@HighlineGuitars Thanks. Last time, i used a epoxy that wasnt clear, more like an ambar color. Fortunately it was on wood so it looks like a varnish. Do you think metallic paper will work, like those to print photos? it should right ?
@everydayshowday51514 жыл бұрын
Wow! I do want to ask how you would do this technique around 45-90 degree bent rounded edges?
@HighlineGuitars4 жыл бұрын
I wouldn't.
@fishbinky3 жыл бұрын
is it necessary to prime with paint? i have a black guitar i want to try this on
@HighlineGuitars3 жыл бұрын
It's always a good idea to prime before painting.
@TheKloneKilla2 жыл бұрын
How do you deal with a very uneven surface after you have done a few coats of epoxy?
@HighlineGuitars2 жыл бұрын
I level sand (carefully) if the surface is uneven. I usually start with 400 grit and work my way up to 800 grit.
@TheKloneKilla2 жыл бұрын
@@HighlineGuitars Thank you - really excited to see how this turns out!
@TheKloneKilla2 жыл бұрын
@@HighlineGuitars My finish is cloudy from the sanding. Will clear coat solve that?
@HighlineGuitars2 жыл бұрын
@@TheKloneKilla Yes.
@fphrigian81836 жыл бұрын
Is that white primer, or paint? And, what grit did you sand it down to? Great job!
@HighlineGuitars6 жыл бұрын
I sprayed 5 coats of flat white acrylic after sanding with 220, 320 and 400 grit.
@laurielindquist39073 жыл бұрын
Does crystalac finish work like 2 part epoxy. I’ve pained a design with acrylics on my guitar and am looking for the perfect finish. I don’t have a sprayer so I would have to brush this. Your opinion would be great. Thanks
@HighlineGuitars3 жыл бұрын
No. It's a 1k water-based polyurethane.
@laurielindquist39073 жыл бұрын
@@HighlineGuitars will it leave brush strokes?
@NITE_SHIFTING2 жыл бұрын
Hello, how might I get in contact with you about having you do a guitar body for me like this project?
@HighlineGuitars2 жыл бұрын
I don't make parts or accept commission work. Sorry.
@tommybyrne80925 жыл бұрын
Have you tried using the Solarez asyour finishing clear coating on the image transfers... ?
@HighlineGuitars5 жыл бұрын
Nope.
@GlennPeoples6 жыл бұрын
I've been wondering recently about putting enamel clear coat on epoxy. So that should be no problem then?
@HighlineGuitars6 жыл бұрын
Why put an enamel clear coat over the epoxy? Just use the epoxy as your clear coat.
@GlennPeoples6 жыл бұрын
Yeah, I was actually thinking of doing it the other way around for silly and overly complex reasons. But you're right, one type of clear layer over another is dumb. I'm just going to sand and re-finish.
@anitabonghit27585 жыл бұрын
i assume this technique will work with a hand drawn pen drawing, right?
@HighlineGuitars5 жыл бұрын
An ink drawing should work fine. I would recommend doing a quick scribble with the same pen on the same type of paper and test the technique on some scrap wood. I'd hate it if the hand-drawn art was ruined by something incompatible with my technique.
@m0ch3r5 жыл бұрын
Hi , im gonna try this method on my own project , but i have little question . I want to do this stuff on guitar with binding, what would you do. Secure the binding before the zpoxy magic , or scrape the zpoxy from binding??
@m0ch3r5 жыл бұрын
and one more , do i need to paint the top with white or i can try it on raw wood ??
@HighlineGuitars5 жыл бұрын
No way would I attempt it with binding in place. I would do apply the graphic first, coat with Z-Poxy and rout then binding channel. Then I would glue on the binding, scrape it flush with the surface and cleat coat.
@HighlineGuitars5 жыл бұрын
@@m0ch3r If you don't paint it white, you'll see the wood through the graphic.
@m0ch3r5 жыл бұрын
@@HighlineGuitars ok , another question , acrylic paint , then zpoxy 2 coats , can i clear coat with poly paint ?? ty for answers , they are very helpfull :)
@MrLupodiinverno4 жыл бұрын
Hello sir .as a beginner what is the best finishing coat you suggest,and what is the best for a pro?
@HighlineGuitars4 жыл бұрын
Crystalac Brite Tone
@TAPION952 жыл бұрын
where did you get your template to make the design???
@HighlineGuitars2 жыл бұрын
I make them.
@jeffpotts61876 жыл бұрын
What about colorfastness? Will the graphics fade over the course of time, or will they still remain bright?
@HighlineGuitars6 жыл бұрын
They will remain bright forever as long as it is kept out of direct sunlight.
@mspguitars67406 жыл бұрын
Personally, I would use a surfboard epoxy like System Three's SB 112 because of its clarity and UV inhibitors. But it is quite a bit more expensive than Zpoxy. Great technique Chris!
@bonehawkofficialbookingand92822 жыл бұрын
Does the bond between the paper and Zpoxy topcoat seem as if it will not separate?
@HighlineGuitars2 жыл бұрын
It’s epoxy, so no.
@bonehawkofficialbookingand92822 жыл бұрын
@@HighlineGuitars mainly curious because I’ve used this technique with a different brand of epoxy and the resin came off in one piece away from the printed paper.
@daverudge18155 жыл бұрын
Does the paint on the guitar have to be white for this method?
@daverudge18155 жыл бұрын
@Thom Waters I did a test on a spare block of wood and some flat black spray paint and found that because the paper absorbs the z-poxy it became dark or tinted by the colour behind it. Looks like flat white is the way to go
@scivanpoon2 жыл бұрын
Easier with a white guitar, or your laser printer need to able to print white.
@warheadone52435 жыл бұрын
LONG WORKING TIME
@johndoe655516 жыл бұрын
so does the zpoxy settle itself down completely flat and leveled?
@HighlineGuitars6 жыл бұрын
To some extent, it will level. You can also thin it with denatured alcohol to help it level better. However, I find it easy to level sand after a couple of coats.
@johndoe655516 жыл бұрын
I see, thanks for the advice. The company I work for is starting to build guitars and I'll basically be the guy who does the painting so I've been really looking into going some graphic stuff like this as well.
@christhompson55533 ай бұрын
No respirator???
@HighlineGuitars3 ай бұрын
No need.
@peterdvideos6 жыл бұрын
I really enjoy learning from your channel. But I would have preferred the graphic image be oriented so it's seen properly while the guitar player is playing rather than sitting on a guitar stand.
@HighlineGuitars6 жыл бұрын
The guitar will be for display only.
@fluidalchemist682 жыл бұрын
Hey Chris, how did you avoid the amber hue with z-poxy? Thanks
@HighlineGuitars2 жыл бұрын
I didn’t. It’s there, just not a big deal.
@fluidalchemist682 жыл бұрын
@@HighlineGuitars oki doki, thanks!
@fluidalchemist682 жыл бұрын
@@HighlineGuitars I see, no worries.
@davidatwood10773 жыл бұрын
How did you create the template?
@HighlineGuitars3 жыл бұрын
For the body or the image?
@davidatwood10773 жыл бұрын
The image,I did find the link to eguitarplans, but I'm not sure if the right one is there. My wife purchased a Bex gears DYI kit. It is the Fender Stratocaster version I believe. This is my first attempt at building a guitar and I liked your video on transferring an image. Thanks for your help.
@melanisticmandalorian2 жыл бұрын
You break my heart, how you choose to pronounce Z(ed) in Z-poxy.
@HighlineGuitars2 жыл бұрын
That's how the company that makes it pronounces it.
@harcourtmudd4 жыл бұрын
Beware of the Tone Police..... Ooo you know what I mean the thin cracked lacquer is the righteous path brigade. I'm not sure all the Tone wood hype is correct. Somehow I got a cheap Ibanez that has the wrong wood with the thick rock hard poly finish that sounds great. I have other Ibanez guitars that cost much more with better build quality that can't touch it. Tone wood with thinner finish and better electronics. Should be better. Not! Got lucky and don't know what is magic about it.
@HighlineGuitars4 жыл бұрын
My theory is that tone often comes from how a specific guitar, because of it's "feel," enhances a player's technique, which brings tone along with it.
@harcourtmudd4 жыл бұрын
@@HighlineGuitars I would like to agree I bring something to the game. However I have to just sing the praise of a cheap Ibanez that some how puts other much more expensive guitars I have to shame. It got me on a Ibanez buying binge. The cheap Gio still ranks above them all. I have since bought a Explorer that has the feel you describe and it also has the tone to match. But it has nothing in common with the cheap Gio. It also cost much more..
@dronebaronnoncommercialpho5494 Жыл бұрын
You should consider taking this video down or inputting more information. While the thot is nice, myself, David Imrie, And Ashleigh Carbonie have all done damage to very expensive guitars using Zpoxy. I used the same type you did, and the same thing happened to both mine & David Imrie s guitars, it went on nice & thick and smooth as can be, as it started to dry is slowly kept separating till it dried like mountains. This was over a very well prepped black paint sanded & prep cleaned to 400 grit.
@HighlineGuitars Жыл бұрын
I'm not going to take down a video because a couple of guys I've never heard of screwed up. I and many others have used Z-Poxy without issue. In fact, that guitar still looks brand new 4 years later.