Hikvision KIS 602 IP Video Door Intercom Kit DC12V Electric door lock connection

VDP Buy Online India : amzn.to/3p4aTkn
Electric Door Lock Buy Online India : amzn.to/37y0Fmk
Hikvision kis602 IP VDP indoor station DC Electric lock connection setup video

[@vitaliyprosto78]

Один нормальный человек , кто показал , понятно, как нужно подсоединить! Спасибо. Thanks so much

[@abraheemkharboush5076]

بارك الله فيك مزيدا من التقدم والرقي Thank you

[@jamesmeader2261]

This video is really good I’ve got the same KIS-602 and have wanted to install an electric lock when I have time. I’ve taken screenshots and notes from this video. Subscribed as well 😊

[@Techlogics]

Glad it helped

[@xavierdeplinval2032]

Thank you for this video! Very clear! I have a HIKVision DS-KV8202-IM: PoE is working but, do you know if there is a 12V output? I don’t find it, but there is no interrest if I can’t supply a lock with power… ? Thank you!

[@leonidruiz4214]

Thanks , great video ! How would it trigger a gate opener to close it back ?

[@bogdandiuk4839]

If your outdoor unit restarts after you open the door: - You need to use external 12V power adapter for your electromagnetic lock instead of 12V output in your outdoor unit. or - You need to use Power Booster Interface (in russian its called: "блок управления замком", so you can google it). It consists of one 240 Ohm resistor, one 4700x25 polar electric capacitor, two 1n4004 diodes. It has 3 wires (contacts): input 12V, common GND, and output for electromagnetic lock. It costs ~$3 If the Power Booster you have bought is not powerfull enough to open your electromagnetic lock, try another one from another manufactor. I think that 4700x25 capacitor is not enough powerfull and you should try 4700x35 capacitor. But I'm not sure.

[@miteshjariwala8456]

Really good presentation. 👍

[@jameswalker3869]

Not really telling how to install it in the actual door. I bet you it is impossible as the moving part of the lock has the cables that need to be connected to the doorbell which is fixed.

[@Asad-vk5om]

Hi, that's an amazing video. Can you show how to set up this 'DS-KIS603-P(B) IP Video Door Intercom Kit" Electric door lock connection?

[@yevhenpohonyaychenko8941]

Very good.thank you

[@jassji]

thanks your video saved a lot of time and effort. IN 602 after doing connections as per your diagram the lock works fine but the strike takes a long time to come back to normal. What to do??

[@jassji]

Bro please reply if there is any solution

[@mxhammed]

Thank you so much.

[@user-rv6fj2zg8x]

This way will work only of you have short cable but if you connect to longer cable and due to high resistance this will not deliver enough voltage to camera during unclocking the door which take high current and as a resukt this will reboot the camera everytime you unlock the door. Connected as normal and found perfect operation.

[@yuricona4158]

Hi, nice tutorial! I was wondering if it's possible from the hikvision app to disable or "long press" the door unlock button to avoid unintentional opening. Thanks you :)

[@linkhyn]

Hi! Is it possible to avoid the use of the call button, and only take and advantage of the camera and the remote unlock door? How would it be?

[@amon5828]

THE BEST WAY TO SUPLY THE LOCK WITH 12 V IS SEPARATLY FROM OTHER SUPLY

[@jafaratili9228]

@TECLOGIC I have connected it and (sometimes) when I press the code the outdoor unit restarts. I looked into the door strike internals and both 12V cables meets inside the unit and shorts, how can I solve it?

[@touchlessgatessrinagar5408]

For dis 603-p model , I want to connect an electromagnetic lock on the door , how to wire it with the outdoor unit , I guess if poe is used to connect the outdoor and indoor , the outdoor can be used for the lock . connect the com and gnd on the outdoor station , 12v dc and no to the lock wires , am I right ?

[@iebooo0]

Can this be used with cat 3 instead of cat 6 between the doorbell unit and the internal screen somehow?

[@shattamovement6601]

Thank you 😊

[@gastogneTV]

I am not getting this to work with the KV6113. This has terminals with the same wiring (12VDC, COM, GND, NO) but when I connect the 12VDC w/ COM and the GND and NO to my 12VDC lock, nothing happens. Even when I connect the 12VDC and GND to my lock, nothing happens. Do the terminals need to be activated of some sort?

[@kmosama5904]

Hello, Bhai ager hamey electric lock jis ki yai video hai aur magnetic lock donon chaheain Hoon tu Kia wo aik he setup pr lg skty hai plz iski koi video bnaen

[@vako1969]

If it's will work on DS-KD8003-IME1? and with Electric lock BEFO 0611? Thank you

[@asifkapadia4001]

DS-KIS602 OR DS-K1T501 which one is latest and which one is more recommended

[@jeetendrakumar6011]

Very nice sir

[@Techlogics]

Thank you

[@ProduccionesAbanto]

una consulta no se si me podria ayudar segui todos los pasos pero tengo un pequeño problema con la chapa eléctrica que aveces habre y aveces no creo q le esta llegando muy poco voltaje a la chapa quisiera ver si me podrian orientar de como hacer la conexión para q la chapa le pueda yo poner su conexion de 12v. Espero su ayuda

[@edwardklkxd]

Ok tengo una inquietud , la puerta solo puedo abrirla cuando tocan el timbre.. pero no me funciona habrirla si alguien sale de casa . translation: Ok I have a concern, I can only open the door when the bell rings .. but it doesn't work for me to open it if someone leaves the house

[@_kick_buttowski]

If i give the power to poe via the outdoor unit, and the door lock coil gets damaged with time, can it damage my poe switch or intercom?

[@rrenyson]

Very Nice Video, can we connect this unit to make telephone calls and use this as a instrument, like if get a PSTN call on RJ11 is there a way to make calls using your Airtel Landline number

[@Techlogics]

Not possible

[@00MorningDew]

I have 3 wires to the door lock. When I connect Brown to GND, Yello to NO1 and Green to NC1, it works with an external 13V DC adapter. When connected to built-in 12V, it does nothing. The problem with the external DC adapter is that the door lock (motor) _ beeps every second. What do you think the problem might be?

[@eyespycctv]

Hi everyone just wanted to know can i run 1 cable from the ds-kis to the strike lock and to a keypad or does it have to be separate? Please advise Because i need to have a a keypad to enter and a push button to exit installed

[@SumiX3D]

how to find positive and negative terminal of electic RIM lock ?? like secure eye as you mentioned in the video

[@Techlogics]

The Rim lock is magnetized by the copper coil only No PCB/Circuit, So that not mentioned +ve / -Ve polarity, Any wire you can use for +ve & -Ve

[@tv-ladik]

Could you please tell me what the latest firmware of this indoor station is (DS-KH6320-WTE)?

[@akhtartherocks]

Need a VDP solution for 3 door lock, each door has separate lock and it has to open seperatley..

[@mijailin01]

Hello!! please could you give some info about how to disable the voice the answers my intercom when I take some time to answer the door? I hate it says the voice that says that no one can answer and to leave a message, i prefer not to have the message. Can you help me? Thanks!

[@CCTVOperator2939]

Rimound kit kese use kerenge sir

[@shiripova]

Hello, is it work on ds-kv6113?

[@sjonmx]

Same question :D

[@guganappu3353]

Hi I am using kis604-p(c) How to connect the lock wiring I don't no tell me anything

[@aslammeethal3876]

Is it's working with motion ?

[@Techlogics]

Motion notification we can receive from app

[@felipefranciozo7722]

hello friend can make this video or some scheme to connect two locks?

[@AbiabangYT]

two lock with same open just pararel the cable

[@CCTVOperator2939]

Smps bhi use hoti h kya sir

[@Techlogics]

For lock smps not required, because from the door station we will get DC12V supply

[@mannamsudheer9480]

Boss him connect app lo register number change karna how

[@rrenyson]

How to connect a external door bell switch

[@Techlogics]

No option for that, but you can connect like alarm input. refer user manual

[@hammoudaelbachir5103]

Thanks. I try to power thé lock from thé door station but it disn't work

[@Techlogics]

The DC 12V lock only will work

[@hammoudaelbachir5103]

@@Techlogics thanks

[@hammoudaelbachir5103]

@@Techlogics I use Electric strike 12V

[@mjaballah]

@@hammoudaelbachir5103 did you figure a way of doing this?

[@drizzle_fog]

howmany indoor station support on 1 outdoor station

[@Techlogics]

we checked upto 2 indoor devices, i think we can connect 2more also

[@drizzle_fog]

@@Techlogics i already connected 5 indoors, but customer need 2 more indoor station , so that i asked the doubt

[@Techlogics]

@@drizzle_fog it's a villa/apartment VDP solution product, so more screens can connect

[@KUMARGT65]

price

[@shankarparab4334]

Music itna loud?

[@mfkhan2112]

U should speak, it would be helpful & a shorter video

[@moazum1]

Can I connect it to Alexa

[@Techlogics]

Not compatible

[@midhunbabuk950]

Wireless elle

[@jameswalker3869]

This is ridiculous, am I going crazy? the part of the lock that has the cables need to be fixed, how can you install this lock that will be moving along with the door sheet when opening or closing, and connected to the fixed doorbell? it doesnt make sense!!!

[@a.alghofaily]

its work with your steps and the device works perfectly, but when you open the door without answering the call, the device will restart by itself !! where is the problem ??

[@Techlogics]

you lock may be defect / give Lock power supply separately

[@a.alghofaily]

@@Techlogics i will try to change the lock , but the lock working good when i answer than open , if i open before i answer the rest issue coming , do you think i have to update the firmware ? Or its from the lock ? Thank you

[@Techlogics]

@@a.alghofaily Give separate power supply for lock

[@cipher-1]

@@Techlogics I think connect directly is a wrong way. Will work if have good ps but how long time???...

[@a.alghofaily]

@Fou2de ايه نعم ، ركبت محول خارجي لان الجهاز ما يتحمل كهرباء القفل ويعمل ريستات

[@najdiyassin]

Null explication

[@thedecentboy0078]

Dont buy any product of hikvision worst company i have ever seen in terms of after sales service they only have their service center in mumbai only. If your product has any problem and manufacturing defect than you have to send it to mumbai on your own. And it will take around 1 month to come back to you. I have recently purchased same model ip vdp its comes with poe switch just after 20 days my poe switch light starts blinking and it stoped giving power supply to my doorbell and tft screen/indoor station. If any body of you are planning to buy dont go for this shit company instead try godrej which gives door service and you may try hawkvision also but dont buy hikvision products.

[@alphak8526]

My outdoor unit restarts