Hipot testing. Cable Hipot Test. High Pot test. High potential Test. DC Hipot Test. Hi pot Test.

In this video
Hipot test is explained with respect to the following points,
1. Hipot testing kit
2. Hipot testing explained with example
3. Testing connection for phase to earth and phase to phase cable insulation test
4. HIpot test voltages as per the standards
5. Safety precautions during the tests
6. A Practical demo of the test
For business inquiries mail to: [e-mail]
Video URL: • Hipot testing. Cable H...
#hipot #hipottest #hipottesting #highpottest #highpotentialtest

[@pietervdberg7055]

Thanks for the clear explanation. It is good to show the diagram and then the test setup. Most videos only explain the diagram or only show the test rig. Then you get lost putting the two together.

[@ElectroGlobe1]

@@pietervdberg7055 Thank you so much for the comment.

[@pradeepraghavan2109]

Thanks for sharing...very informative topic and well explained

[@ElectroGlobe1]

Thank you for the comment

[@chaudhrymujeebali7565]

its really good information to understand Hipot testing

[@ElectroGlobe1]

Thank you for the comment.

[@tamilchelvanramasamy8733]

Lucid and elegant!!!!!! Thanks Sir

[@ElectroGlobe1]

Thank you for the comment.

[@karingulasrinivassrinivas4515]

Super 👌 sir your explanation is very good

[@ElectroGlobe1]

Thank you for the comment.

[@nerosmero1183]

Thanks for sharing this great experience. One question: How much the Hi-pot test results should differ between old and new cables? Regards

[@ElectroGlobe1]

Thank you for the comment. Either old or new cable, the high pot results such as leakage currents, voltage withstand time, should be as per the standards.

[@nerosmero1183]

@@ElectroGlobe1 what about the test voltage values?

[@ElectroGlobe1]

@@nerosmero1183 In the video reference standards are mentioned for test voltage values.

[@shaikhsiddiqui8560]

Very good information.

[@ElectroGlobe1]

Thank you for the comment

[@OmkarNikam-q5p]

Sir if you break it down to its components, How does your test transformer can produce up to 60KV of voltage from 230 volts. please explain.

[@ElectroGlobe1]

By using Transformers.

[@pietervdberg7055]

The test transformer in the diagram is a step-up transformer meaning the voltage is stepped up (increased) to the required kV level to do the test.

[@evervasquez2489]

Cuales son las valores maximos de corriente fuga o cual es el standard

[@jims9916]

Thanks. In my Hipot Kit for DC, In the diode how much oil should be there. In our case it is 50%. as there is a small hair line crack at the top of diode. is it recommended to test when the oil in diode is only 50%. What oil is used to top up. Thanks

[@ElectroGlobe1]

Thank you for the comment. It is advisable to refer to the manufacturers manual.

[@syedimam8261]

Didn't shown leakage current during test How much leakage current?

[@ElectroGlobe1]

Leakage current was around = 0.5 mAmp

[@syedimam8261]

Thanks

[@motivatednandu]

But when you apply DC voltage to primary of transformer you will get 0 output so how can you apply voltage

[@ElectroGlobe1]

Converters and inverters are used to transform AC into DC and vice a versa. At transformer ends only AC is applied. Transformer does not work on DC current.

[@pietervdberg7055]

The test voltage level is set by the controls on the incoming 230V before the auto-transformer. The voltage is stepped up in the Test Transformer to the required level and only then is the AC from the secondary rectified to DC and applied to the test object. DC does not flow through the transformer. The diagram shows only one diode but it represents a sophisticated rectifier unit that produces a smoother DC output.

[@wolfpackrc]

Good job

[@ElectroGlobe1]

Thank you for the comment.

[@chaudhrymujeebali7565]

GREAT MY FRIEND

[@chaudhrymujeebali7565]

You are doing well dear

[@syedaijazmohiuddin5237]

Sir, at end+ 1700 I am not getting please explain

[@ElectroGlobe1]

The Values are as per the standard.