Hisense LED TV (no power repair)

How to modify a power supply. Tips and Tricks. please like share and subscribe. Thanks

[@Terracote1]

Thanks!

[@tevzTVTevatronics]

Welcome!

[@lexstarv.p.9171]

Your demonstrations are so clear and precise, thanks again for another awesome video.

[@brucewalker1908]

Your videos are just fine. Ignore the complainers.

[@JeanDAVID]

you are the best electronic guy on tv repair !

[@payusavisit3482]

Very useful and éducative conversion 🎉

[@ayubtechke4294]

This is not for beginners if you understand what is happening no matter the noise you will get it 😂. Nice work Sir

[@ssee9130]

Very interesting thank you 🎉

[@aminulvivo1420]

Good video sir 🌹

[@priyanshirajshivanshiraj5044]

Good job sir

[@deejayrahman]

Sir!!are just good when it comes to electronics..am soo lucky I found ur channel cos am really learning alot from you

[@tevzTVTevatronics]

Thanks and welcome

[@Fardeenfarwest]

Thanks Tevz for these video. Excellent work. ❤

[@pacmanbob4260]

I think the back ground noise is great ! I’m watching a repair so I don’t mind - I especially like the rosters ! !

[@bobanmanic1235]

Thanks a lot for the video.👍

[@venerandarain3]

thanks for sharing your modification skill sir. glad to watch your video again after several days.❤

[@aungzawoo9926]

i always see your video good teaching i love it

[@kaizen1071]

Teşekkürler Tevz bey. Harika iş. Sağlıklı günler.

[@bachirhannouta5532]

Thanks from moroco

[@NorlysHernandez]

nice repair master as always

[@tevzTVTevatronics]

Thanks 👍

[@bshi0288]

Thank you very much for your video uploading.By the way, it is possible to cutoff end of solder suker with small scissor,And It will make you to use your solder suker without detach soldering tip from pad as you did in your video (4:50-5:10)

[@prabhuprabhu4274]

Nice

[@pak_guru_toro]

Awesome modification

[@tevzTVTevatronics]

Thanks

[@PasinduDilshan-we7so]

Wow 😮

[@hasantamer9199]

good

[@greendata1]

that was awesome

[@rajeshjadav1240]

Nice. ❤

[@tevzTVTevatronics]

Thanks 😄

[@balabala6610]

Thanks sir

[@heikobarisch3235]

Respekt Mega ein IC rettet einen kompletten Fernseher. Dankeschön für das lehrreiche Video. LG.Heiko

[@karanahuja6302]

Your repairing videos are excellent and your camera quality is awesome. 😊😊

[@tevzTVTevatronics]

Thank you very much!

[@electronicrepairservice2020]

Awesome modification, excellent repair! Yes, videos do take a long time to produce, I have some from 6 months ago that I haven't edited yet. It's hard to do both - work and edit videos.

[@yowunpansilu]

Tevz we need other electronic repairs too not just tv s

[@jerrythabo9045]

Thanks Mr Tevz your videos are the best ❤

[@JoeCentralTech]

Like always nice work

[@yuliantoanto3884]

Terima kasih sudah berbagi ilmunya

[@darfor12]

Thankyou about this informations

[@emilioemilio1710]

Muchas gracias por compartir!!!

[@aungzawoo9926]

❤❤❤❤❤❤❤

[@noureddinecherradi5037]

Good work thanks

[@krasag]

Полезен видеоканал да специалисти в ремонта на радиоелектрониката

[@ifeoluwaomoyeni]

Thanks for sharing🎉🎉

[@leevan1424]

good job thanks

[@hakanbagonu176]

Türkce altyazı olsaydı daha güzel olacaktı👍

[@entechdroidboardemulator9533]

I want to come over and learn

[@shalenprasad1342]

Very nice video sir thanks 😊

[@tevzTVTevatronics]

Most welcome

[@lorenzolopez8512]

Jejje los que sabemos un poco de electrónica,el audio es lo de menos solo con mirar lo que hace sabemos que está haciendo

[@gabrielcuevas5837]

Saludos amigo.

[@sultanrasulhanow6690]

👍

[@bineshchauhan8713]

Thanks sir Please give small diagrqm of new modification on paper for screen shot, so new lerner understand and imove them work

[@shopyd]

Hello sir.your videos are perfect and very helpful.is there a way to contact you for asking questions about tv repair.i repair tv and others too.thanks

[@sunsys0]

#important

[@tevzTVTevatronics]

Indeed

[@Nosan얼음속붕어]

한국의 동부대우전자 TV L43S6550BK 같은 보드입니다!

[@tevzTVTevatronics]

Im not sure

[@riasoria7411]

Please don't skip adds❤

[@robinsonsoto8471]

Can you provide more information on the instalation of the Strw6053n.

[@estebansuarez2957]

Hola tvz y no era mejor hacer un bypass como hizo en otro video ademas se ahorra en componentes 🤔

[@shaik5336]

I'm the first like and comment ❤

[@shafiahmad6795]

I am your subscriber and also give like to your each and every video that you upload

[@tevzTVTevatronics]

thanks

[@GODofAbrahamIsaacandJacob]

@tevTV, what kind of device do you use ? To Discharge you're Capacitors ? Do you use a ground Clip, attached to wire, attached to a Resister, that attaches to Discharge metal Rod, that you simply touch to main, Capacitor.+ Positive Terminal ? For 5-10 seconds ?

[@tevzTVTevatronics]

the resistor 220 ohms 20 watts.

[@mahmoudnaser453]

hello Mr tevs,I, didn't see your for long time, where are you, may be you go to travel or you leave your house ,or something else ,so are you ok or something wrong?I hope you're good health,but I have a question,are you from maylasi,or Singapore or in the area of nearest,

[@tevzTVTevatronics]

I'm just busy with the repairs. I am from the Philipines.

[@bshi0288]

Thank very mcuh for reply! I plugged in AC cable and checked DC voltage of AT24C04 IC which seems to be eeprom for this 29 inch LG CRT TV.I placed red probe to pin #8 of AT24C04 and black probe to pin #4.It measured 5.084Vdc regardless of clicking power switch.I also pressed channel button and other button on the remote controller But It won't make LG 29 inch CRT TV to display any screen at all...

[@tevzTVTevatronics]

try hang the eeprom

[@bshi0288]

@@tevzTVTevatronics What is meaning of hang the eeprom? dose it means to replace AT24C04 IC with new IC?

[@tevzTVTevatronics]

@@bshi0288 just hang it and try it, if the tv turns on it? it means it is in standby mode. or it has an EEPROM program issue. Check if you have a remote try to remote it, but resolder back the EEPROM before you remote it.

[@bshi0288]

@@tevzTVTevatronicsI resolderd all pin of EEPROM(AT24C04) on the bottom of PCB and I repeated to plug in AC cable and push power button on the remote and unplug AC cable, more than ten times. I noticed that whenever I push power button on the remote,DC voltage of B+ filter capacitor(160v 100uf) suddenly became 120Vdc and it gradually decreased until it reach 38Vdc.But Unfortunately, No matter how repeat plug in, push power button and plug off,It won't display any screen at all

[@bshi0288]

A few days ago, I noticed that there is no faulty in the HOT area. So I doubted maybe there was loose contact on the pin of IC,Beacuse This CRT TV was manufactured over 25 years,So solder joint would not as tight as twenty five years ago. And it seems that weight of its PCB is about 2kg,I think that Whenever I deposited this heavy PCB on the floor,this would put pressure on the pin of IC.So there would be minor crack on its solder joint. I soldered all pin of LG8708-08A, GL3812,TB1231N and Turner TUSHB-A07A at the bottom of PCB, and It finally displayed screen! In fact, I have another CRT TV(LG slim 21fu1r-ns of 220 voltage) which was not able to display any screen.So I did IN CIRCUIT Testing all of capacitor with ESR meter. I found a capacitor which has no ESR and capacitance value at all, It was connected to horizontal coil(250v 1uf). So I replaced this capacitor and other capacitor which is located in the vicinty of FBT(250v 4.7uf) and in the vicinty of Vertical Deflection Booster(STV9326)(35V 100uf) which has somewhat higher ESR value,So I also replaced these capacitor,too. After replacing three capacitor,It finally succeeded to display a screen,But,the screen was very bright and It displayed lines across the screen . Worst of all, IT IS NOT ABLE TO CONTROL BRIGHTNESS with screen adjust potentiometer on the lower FBT... Besides I heard a weird static sound near CRT anode cap whenever I turn off this 21fu1r-ns CRT TV I really want to control brightness with screen adjust potentiometer on the lower FBT and get rid of weird static sound. I really very much appreciate you if there is workaround to repair these problem.

[@cmcchrisable]

I wanna reach out to u to ask for guidance on a tv repair

[@johnluisborja6480]

Spokining dollar pla toh c master wla akong mpupulot d2 bye😂

[@Junior-ff7ee]

Hie some of your videos you did not put str on heat sink why or am wrong?also may you do a video of modification of a double mosfet power supply ?

[@tevzTVTevatronics]

Ill try.

[@mahmoudnaser453]

may be????????

[@user-up2hn2yi6o]

What is the name you used the temporary fuse??

[@tevzTVTevatronics]

resistor

[@jaym5938]

Why using the STR-W6000S so much? It seems a bit of a pain having to jerry-rig it. Is it a lot cheaper?

[@tevzTVTevatronics]

This TV is cheap, could you let me know what you want to replace it? a power supply that is more expensive than the tv?

[@bshi0288]

I have 29 inch LG CRT TV which did not display any screen at all. When I plugged in its AC cable I measured DC voltage of B+ filter capacitor(160v 100uf), it measured 38Vdc with DMM. But as soon as I click power switch,It suddenly soared to 120v and gradually decreased until it reach 38Vdc. And I also measured pin #9 of STR-S6707 in the HOT area with analog meter and it also soared to 7.3-7.5 Vdc as soon as I click power switch, and gradually decreased until it reach 6.4Vdc. I purchased another STR-S6707 and replaced primary STR-S6707 with it by soldering but that would not fix this voltage decreasing problems.. Would you give me a clue What cause this symptom of decreasing voltage of B+ filter capacitor and VCC of switching ragulator?

[@tevzTVTevatronics]

Some power supply goes to a lower voltage when the system is in standby mode. try press the channel up or down or other power booton. Check also the 5 volts standby.

[@esilvap26]

Lightning damage.

[@tevzTVTevatronics]

I think so

[@damochannel1752]

Sir san po kayo located

[@tevzTVTevatronics]

laoag city

[@mahmoudnaser453]

the board I think it's built with digital reiciver

[@tevzTVTevatronics]

No, It is not.

[@michaelngobeni5640]

Do you sell smd components

[@tevzTVTevatronics]

No

[@FSX3000]

how the hell do you just know what mosfet to replace with and how to connect it ? how did you learn these things

[@tevzTVTevatronics]

We can learn from our experiences and knowledge. Even Chimpanzees are capable of innovation. They can come up with new ways to solve problems, such as using a stick to reach termites out of a mound.

[@preston963]

Dodgy as fark!... Not impressed!... Been a tech 40+yr.

[@ZafarIqbal-qy9qe]

❤❤❤❤❤❤❤

[@dominggobautista3468]

Thanks sir

[@tevzTVTevatronics]

Welcome

[@dominggobautista3468]

Thanks sir