Repair coolant leaks in the engine block, head gasket, radiator etc with Holts Wondarweld. www.holtsauto....
Пікірлер: 74
@ammar13863 жыл бұрын
I thank this wonderful company that saved me from disassembling and maintaining the car engine. Thank you with all my heart. وللأخوان العرب والله المادة رهيبة إذا خلط الزيت مع الماء ركب علبة وخلي السيارة تحمى وبعدين طفيها واتركها للصبح او ٨ ساعات وإذا يطلع فقاعات وصوت من ضغط من علبة ماء الرديتر أو الرديتر يكون رأس الماكينة ملتوي حط علبتين ويتسكر الإلتواء ويشهد الله جربت الطريقتين والحمد لله نجحت ١٠٠% والله ولي التوفيق
@حسينعبدالله-ت2ظ3 жыл бұрын
اخوي عمار الله يعطيك العافية ... بالنسبة للمنتج كم من الزمن اترك السيارة شغالة اذا وضعت المنتج ؟
@AbuYasmeen23 Жыл бұрын
شو صار معك
@ابنسالمالطياري6 ай бұрын
@@حسينعبدالله-ت2ظ15 دقيقة فقط هكذا قال في الشرح التوضيحي في الفيديو
@fortitudevalance84242 жыл бұрын
I have used it in my Land Rover’s previous engine just to seal off any micro cracks that may appear as a preventative measure. I did not drain the Wondarweld for at least 3 days and I replaced the thermostat anyhow.
@abelghita76324 жыл бұрын
How many bottles for a mercedes sprinter 2004 2.2 diesel?
@عبداللهعبدالرحمن-ه6ذ Жыл бұрын
Do i leave the pressure cap open or close during this process?
@24kwsths6 ай бұрын
i thing yes
@inspirasiimaginasi Жыл бұрын
This product is unavailable ON-SHELF in Malaysia.
@judenrahim4839 Жыл бұрын
dalam lazada ada jual
@inspirasiimaginasi Жыл бұрын
@@judenrahim4839 Saya prefer beli offline dari rak kedai terus. Tak gemar sangat beli online, kecuali terpaksa.
Tuan buka thermostat n tuang terus atau tuang dlm sparetank? @@inspirasiimaginasi
@MsVishnu99 Жыл бұрын
How many hours starting the vehicle process time
@24kwsths6 ай бұрын
In the video it says to leave it for 15 minutes until the thermostat opens. I read somewhere to leave it for 3 daysto drive it . I did it for half an hour out of 3 times because the thermostat opened at 15 minutes... if you are asking how long do you leave the vehicle when you turn it off with Holts Wondarweld in it, it's good to leave it for 8 hours and then wash it well!
@yafa4000.4 жыл бұрын
Very excellent. I used it in my car.
@ابوالبراء-ط8ق4 жыл бұрын
السلام عليكم اخي كيف نستخدم المادة لان التعليمات بالانجليزي ولك جزيل الشكر
@yafa4000.4 жыл бұрын
@@ابوالبراء-ط8ق ®شرح مادة المكينه® اول تكون السيارة واقفه بارده وبعدين تفك نصف مويا الرديتر وبعدين تفك بلف الحرارة وبعدين تفك ليْ الخرطوش من فوق الرديتر وتخلط الماده بماء وتصب وتسكر لي الخرطوش وتزود الرديتر اذ باقي له وتشقل السياره ساعه وتشوف كيف الحرارة. وتخليها الين اليوم الثاني وتمشي فيها لو تمسك خط افضل.
@wengsiongsai28152 жыл бұрын
How ?is it function well?
@تمامالشحادة11 ай бұрын
.
@ساميالحربي-د4غ10 ай бұрын
@@yafa4000.التعليق غير واضح
@kamborno19313 ай бұрын
Your quick answer will be appreciated. I ordered the product and I will have it today, but I am facing a problem in disassembling the thermostat, as access to it is difficult in my 2008 Mazda 5. I will add it to the other hose. Will this help?
@longshotdiedtired1582Ай бұрын
It’ll work just fine as long as you remove the thermostat
@srenthorning51954 ай бұрын
How it work if its on the pressure side , kompression will blow i away or
@taykokhuat Жыл бұрын
What will happen if after repaired, the Holt's solution is not drain off?
@24kwsths6 ай бұрын
it will clog the radiator cooler and maybe the thermostat too. Works with water, not antifreeze!!
@إبراهيمأحمد-ه6ث4ز13 күн бұрын
good 👍
@richardoloot12952 жыл бұрын
i have oil in my expansion tank, so there is a crack from internal oil channel to internal coolant chanel. There is NO external leak visable. How can this product distiguish this type of crack, i dont understand how it can work/if it can work in my case?
@mrahmedar18 ай бұрын
Dear, regarding the V8 engine, one or two cans are enough
@almubakh7 ай бұрын
Does it work for turbocharger leaking?
@masonichisenga30324 жыл бұрын
I have been told to pour this straight into the radiator and that it will fix the leaking radiator.
@masonichisenga30324 жыл бұрын
It worked like a charm! 🤸🏿♂️
@MrRichard570004 жыл бұрын
@@masonichisenga3032 i believe it s disignd for cracks in cilinderheads and cilinderbloks.....
@masonichisenga30324 жыл бұрын
@@MrRichard57000 yes, that's why I was sceptical about it being able to fix my radiator, plus not following the instructions to pour it down the water pump.
@MrRichard570004 жыл бұрын
@@masonichisenga3032 well the instructions say pour it in the engine block(behind the thermostat) important is that you use only water, no antifreeze.... I'm curious if the wonderweld is going to make an improvement in my case.... I just let it in there and before the winter I chance it with antifreeze...
@masonichisenga30324 жыл бұрын
@@MrRichard57000 I am curious, in the case where the cylinder block has a crack as it were, doesn't that mean that oil and water are mixing and if that is the case, don't you have a host of issues that won't wait for you to pour this stuff in it...
@nickgenericusername4 жыл бұрын
Thank you for this. Unfortunately all the mechanics i've asked about using this product just say to pour it directly into the radiator...
@nickgenericusername11 ай бұрын
@Pitirisek unfortunately I had no luck making this product work for me. No idea how far gone that engine was...
@24kwsths6 ай бұрын
No, it's better in the thermostat position. A trick to avoid removing the thermostat is to drop it into the radiator's radiator pipe which is right below the thermostat! In fact, you can join the 2 pipes of the radiator together so that it doesn't risk getting clogged when you drop it in for the repair!!
@24kwsths6 ай бұрын
@Pitirisek I have read up to 3 days and then rinse well.
@CliffordPeterViljoen6 ай бұрын
As my thermostat sits below the engine block, can I then just throw it directly through the outlet pipe into the engine block from the top?
@24kwsths6 ай бұрын
@@CliffordPeterViljoen I assume that since in the instructions the engine must be cold and run with the thermostat closed for these 15 minutes until it opens as it says, the water will not turn before the material takes effect. because it is greasy and to get it in contact with the whole head and the head gasket, add some water after the Holts Wondarweld into the pipe you will pour it
@rasinapnah95742 жыл бұрын
I just put this holts in my expansion tank cooler few minutes ago? It need to drain it back or just let the liquid in that cooler? Help me
@wengsiongsai28152 жыл бұрын
Is it function?
@americantruckeringermany83946 ай бұрын
@@wengsiongsai2815 do you are alive?
@wengsiongsai28156 ай бұрын
You died Holt can't save
@americantruckeringermany83946 ай бұрын
@@wengsiongsai2815 who you or ?
@24kwsths6 ай бұрын
It wasn't for this expansion tank. But for the thermostat pipe and it definitely wanted emptying and flushing after 3 days
@ahmedazzam85342 жыл бұрын
اين.يباع.هذا.المنتج
@bluemoon2702 Жыл бұрын
عند محلات زينة السيارات ٣٥ ريال
@احساسشاعر-ض6ف Жыл бұрын
@@bluemoon2702خديتها اليوم ٢٥ ريال من بنى ماللك حدة
@bachakhanbielefeld82193 жыл бұрын
Tank you
@sasookicool11852 жыл бұрын
كذابين ماده فاشله عن تجربه وخصوصي ماكينه المنيوم
@jgijljhj85726 ай бұрын
ومكينة سوناتا2008حديد؟
@donjuanjt Жыл бұрын
@HoltsAuto Your urgent response will be greatly appreciated as I need to use the product now. When using it in a vw golf mk1 1.6i afx engine, do I need to remove the thermostat? As my thermostat does not mount to my cylinder head but instead, the bottom radiator hose where it connects to my water pump, where my thermostat is seated, inside a flange on the water pump.
@HoltsAuto Жыл бұрын
Hi there, as this is technical question, could we please ask that you contact our technical team at info@holtsauto.com they will be able to advise. Thank you!
@24kwsths6 ай бұрын
To work well it obviously needs to drop into the cylinder head so you can drop it into the pipe that comes out of it and goes to the water cooler.
@MrRichard570004 жыл бұрын
used it to repair a minor crack or leakage from cilinder gasket.....can i leave the wonderwelt in the engine for a few days,ore do i have to flush it out wen it cooled down?????
@MrRichard570004 жыл бұрын
@Ons Huis the thermostat opening is big enough I think, I could worry about the radiator tubes.... Radiator tubes are 1.5mm I estimate but cracks over 0.75mm can t be repaired I thought? Anyway for now it s flowing and cooling as it should, still have a bubble from time to time which will remove a bit of coolant from my radiator..... Overall till now mildly content, we made progress because I have less bubbles and air as before.... Maybe it needs a few day more ?
@kelvinchua3973 жыл бұрын
May i know is it safe to keep the wonderweld in the engine? How long u flush it out?
@24kwsths6 ай бұрын
In the instructions it says when it cools down, elsewhere I have read 8 hours after it has been washed off. In a parts store they say after 3 days with gentle driving!