Home Automation using arduino bluetooth | Smart Home | Manual and smartphone | part 1

The home automation circuit is built around an Arduino Uno board, Bluetooth module HC-05 and a 1-channel relay board. The number of channels depends on the number of appliances you wish to control. Arduino Uno is powered with a 12V DC adaptor/power source.
This channel to share exciting videos of Arduino projects,Electronics and electrical easy diy projects to share with you I hope this projects will be helpful for you to create something new .
Do not Forget to like comment and subscribe my channel.
SUBSCRIBE LINK:-
/ @slideas1
Arduino Code :-
www.mediafire....
My Other videos :-
1. How to control DC motor and Stepper motor with L293d motor driver Arduino
• How to control DC moto...
2. l298n motor driver with control DC motor & speed control unipoler & bipoler stepper motor
• l298n motor driver wit...
3. servo motor arduino
• servo motor arduino |...
4. Top arduino projects 2021 for covid 19 | coronavirus protector | Sterilize Stationery
• Top arduino projects 2...
5. NEMA 23 | NEMA 17 | NEMA 34 with TB6600 stepper motor driver and Arduino
• NEMA 23 | NEMA 17 | NE...
6. How to Build a Low-Cost KZbin Studio
• How to Build a Low-Cos...
7. How to use W1219 Temperature controller/DUAL Display
• How to use W1219 Tempe...
8. How to make an LED VU-meter using Arduino.
• How to make an LED VU-...
9. LED chaser with 32 effects |led patterns with Arduino | Code in Discription
• LED chaser with 32 eff...
10. How To Make Automatic Touch Less Non Contact Water Tap At Home/office
• How To Make Automatic ...
11. How to make best car reverse parking alert system using arduino / DIY / arduino projects
• How to make best car r...
#HomeAutomation #ArduinoBluetooth #SmartPhone
projects,and,products,home automation,How to make home automation using Arduino and bluetooth,how to make home automation project,home automation projects,home automation using bluetooth module,hc 05 bluetooth module interface with arduino,hc 05 bluetooth module working,Bluetooth module hc-05 with Arduino,home automation in hindi,bluetooth based home automation,bluetooth based projects,automation,home,home automation using arduino and bluetooth
home automation using arduino,home automation project,home automation arduino hindi,home automation arduino uno hindi,home automation using arduino uno and bluetooth module,control room lights with arduino,control room lights with mobile,home automation using arduino and bluetooth,home automation,home automation with bluetooth,home automation arduino projects,home automation arduino projects hindi,arduino projects hindi,arduino projects with code,harsh sharma,omhome automation,arduino projects,smart home,homeautomation easy,arduino,mrarduino,project for begineers,home automation bluetooth,home automation x,home automation ideas,home automation system,home automation 2019,home automation diy,home automation hub,home automation india,home automation arduino,home automation arduino project,home automation arduino uno,home automation bangladesh,home automation by arduino,home automation best,home automation cheaphome automation,wifi,bluetooth,blynk,application,app,smartphone,controlled,how to make,work,tutorial,how to control,appliances,devices,lights,fans,code,program,mit app inventor,development,how to make app,raspberry pi,arduino,relay,design,wireless,viral science,viral dodhia,easy,free,project,final year,build,connection,automate,house,home,automation,google assistant,ok google,voice,gsm,gps,command,robot

[@osmondbooysen9641]

Great tutorial. How would we connect this in a way that allows switching it off via bluetooth if its manually switched on?

[@jailbreak7750]

turn on switch don't switch off, stay on. turn off from u'r handphone. is it safe?

[@reynaldoacobajr.9006]

better to use 3-way switch so that you can turn on/off thru phone or switch. in that way, the logic will be like XOR.

[@naveenwilliam3594]

Hello bro i have a small doubt if the bulb is manually on through the switch can i turn it off with bluetooth and vice versa and i dont know how to wire it that way can you tell me how to do that if you know plz

[@VivekGupta-xp2np]

Nice Dear , tried with many video but this one really solve my issue. thanks

[@slideas1]

Thank u

[@tumpalasindhu5382]

everything is good but light doesn't controlled with bluetooth. what is the reason? what can i do to make light controlled by bluetooth app?

[@dammdaniel9953]

Jumper wires

[@EWaB-ou4lc]

May be that you did not connected the system correctly

[@libinmathew1068]

Bulb 💡 glow chythooo???? Reply

[@VishalMudgal-gw5jn]

Define Pin 13. And I think the Circuit is very easy.

[@Sazia_Cooking_Creativity]

Wonderful video Thanks Brother

[@slideas1]

Thank u bro....

[@uwiringiyimanawilson3473]

you are a good teacher. by the way, can you teach me how to make arduino programing

[@slideas1]

Welcome and following my channel .....

[@bgm4019]

Bro can I use hm 10 blutooth module instead of hc 05 and need to make some changes in code please reply

[@aljayramos5437]

can I use different switch?

[@pradeeppatidar-f4l]

nice👌

[@ayodgaming123]

සුපිරි වැඩක් bro😃

[@slideas1]

Thank u bro

[@bkcganeshblogs]

How to increase buttons in Arduino bluetooth control App .only 6 are provided.

[@bkcganeshblogs]

Give me answer sir

[@Allroundtube--113]

Can i use it over long distance???

[@donaldiro5398]

Can this work with HC 04 Bluetooth module

[@suranjanghimire659]

Thank you

[@chidiayoanasonye9243]

Plz I don't have a PC . how can I upload the code using my android phone. I tried with arduino droid IDE app on my android phone and all I could get is a blinking relay and light connected to the relay . Why is it not turning on and off through Bluetooth controller app on my phone ? . plz assist

[@amzsingh6376]

Thank you Bro, one trick that can fullfill my 5-6 hr, please remove RX and TX pin before uplode code

[@slideas1]

Thank u

[@atiya_belim]

Hey . Please tell me the code will be same for different Arduino right Mine is slightly different so this code will work?

[@yupadyy204]

Hello, I am from Indonesian Can I ask what happened when we turn on the light with Bluetooth and we disconnect Bluetooth with Arduino? Are the light will turn off?

[@slideas1]

If the bulb was lit at the time of disconnecting the bluetooth, it will continue to be lit in the same way. If the bulb is off The bulb is still off.

[@kelvingathiru6567]

So technically your neighbor can control your devices if he's connected to your Bluetooth?

[@Tech.Tricity]

Hello sir please how to upload aurdino code please provide information step wise Please reply sir 😊😊

[@multinogaming07]

Can we control our room c link fan by Arduino Uno by proper circuit structure?

[@swapnalipadaval5449]

What is the component of 220V Ac plz tell me name of this component

[@meeraliakbar12]

Can i do this project with arduino nano??

[@slideas1]

Yes of cose

[@armylovergolusinghrajput3618]

Three bulb lagar kar ek video bana dijiye

[@Mupparapuvyshnavi]

How much is the total price of components?

[@Tukaram_Achugatla]

The Code file is not opening...😥

[@madhyamdhartalvar]

Bro सही से open कर

[@osmanelkinani]

There is a fatal error in that you are powering the lamp from 220 volts from the relay and the switch side

[@supritgawande8261]

Can you please send this programing link ? The link given by you is not opening

[@slideas1]

Code in discription ...download

[@shaheryaraslamm]

When we are entering password for Bluetooth It is going in saved not connecting.. please explain

[@AbdulMajid-vn8lw]

Hello, your given link for downloading the code isn't working. Please share the code.

[@tienngo6357]

Can i have a Diagram of this project Sir ?

[@vinay6492]

Complete circuit was working but had a problem with the bulb it's not glowing

[@nathanieldavidmodesto3243]

Have you resolved your problem? Regarding the bulb not glowing?? Do you face any problems when you upload your code?

[@piyushkumarIITD]

Hi all, I'm unable to open the Arduino code link, can you make it available in another way?

[@slideas1]

E malli please ?

[@bharadwajthangella-bz9jv]

Bro i need the correct code

[@gameofdeath1731]

i have bought 12 v i can observe the green light turning on and off.but bulb is not glowing i checked connection

[@nathanieldavidmodesto3243]

Same.problem brother, have you resolved it yet?

[@gameofdeath1731]

relay module is not letting current to flow on bulb

[@gameofdeath1731]

the green is also like low voltage

[@sherollin]

can we still control even we going out...that far from home

[@Saiteja-bg9gj]

No we can't cause Bluetooth range is not so far, for that a wifi controller need to installed in your home.

[@sanjingot6486]

What is the name of the wires you used to connect the relay module, light bulb, and switch?

[@sasmitasahoo1787]

Jumper cables Three categories M-M F-F M-F

[@rishith3010]

How can we connect multiple lights in this?

[@slideas1]

Use a model with several relays

[@danielikhmall3539]

But do we need to change the coding?

[@norbertkiss112]

Pls code 8ch relay panel.

[@kkr_gaming_]

What is the exact price

[@gameofdeath1731]

can it be any codeing issue

[@ranjithbandara4950]

Aiye oya Arduino uno Programming karala den නැතිද ..oyata permanent කළොත්..

[@gameofdeath1731]

codeing any thing we have to change a bro

[@polepeddibharat1315]

Bro nidhehara program vunthe naku petu link petu bro

[@leonelolvera9560]

Es un interruptor de 2 vías ???

[@jb_labs]

Unfortunately not. If one is on, then it cannot be turned off by other ie AND gate

[@karangamer3865]

From where i can order this model

[@boringmemes5718]

Sir the code given in the discription gone expired an alternate code for it ?

[@slideas1]

Send mail

[@boringmemes5718]

@@slideas1 i don't have mail please send the code in comment section

[@sanjaysaravana7218]

What if I on both of them

[@SyedAun-dn8tu]

circuit diagram?

[@chidiayoanasonye9243]

Could you please show step by step on how to program the auduino

[@slideas1]

Good idea ...👍

[@karlsaariste]

you can also just download the code

[@mdtareqrahman3163]

How much arduino and relay?

[@badabomaxime7053]

svp je veux que vous m'expliquer comment faire pour créé le code c'est inpeut floue pour moi svp sinon j'aime votre video

[@gameofdeath1731]

how should we erase old command

[@keep-lung-heart.6689]

hello bro the code is not working

[@tradingview5363]

cAN I RUN A CIELING FAN INSTEAD OF BULB?

[@slideas1]

Yes definitely

[@salmamulla8572]

What about that wires ... What are they called....

[@slideas1]

Jumper wire and auto wire

[@asada1939]

What happen if both switches and bluetooth turn on

[@slideas1]

Even then the bulb is on

[@jonalddejesus6726]

it looks like a 3way switch

[@arielmvoto3012]

Salut peux tu m'envoyer le lien du code bluetooth s'il te plaît

[@raj1.88.]

Code was which language

[@MiskirDires]

The code

[@uwiringiyimanawilson3473]

plz help us to study arduino code

[@YogeshKumar-ue6sm]

4 relay ke liye code do na

[@dhanooshb2871]

How to download that application which we can connect in bluetooth

[@slideas1]

Click the arduino library link to download

[@rabiulislam3406]

app link plz

[@adilabusafa]

يتعذر الاشتراك ولا يوجد جرس-يتعذر الاستجابة لكل طلباتك-يتعذر التعليق-لا أعلم .

[@kolarucovaipasanga7672]

Block diagram venum bro

[@kolarucovaipasanga7672]

Ppt venum pro

[@vamsimylavarapu9352]

Code link not download bro

[@slideas1]

Re try bro....its working ....

[@ohasaliyo971]

are you sri lanka

[@slideas1]

Yes 👍

[@daniyelutellagorla4198]

To slow

[@Mythologstory]

Arduino code bhejia sir

[@slideas1]

Code in description ....download ....

[@alyaaahmed4462]

can i have your code ,plz ?

[@slideas1]

code in discription...download

[@kulesiswarkulesh2032]

@@slideas1 where the code in description ? Please reply

[@slideas1]

@@kulesiswarkulesh2032 www.mediafire.com/folder/4ovq4kljc9utw/bluetooth

[@kingofscience1437]

Tell bro Please

[@Art_Raunak]

Bro plz reply

[@slideas1]

naino ke saath bhee aisa hee kiya ja sakata hai.

[@Art_Raunak]

@@slideas1 thanks a lot sir i complete it

[@slideas1]

@@Art_Raunak great 👍

[@alemayehudemssie7166]

eeeee

[@techwithalan7554]

Bro the code was not open pls put the code on comment pls

[@slideas1]

char val; void setup() { pinMode(13,OUTPUT); Serial.begin(9600); digitalWrite(13,HIGH); } void loop() { if(Serial.available()){ val = Serial.read(); Serial.println(val); } if(val=='1'){ digitalWrite(13,LOW); } else if(val=='2'){ digitalWrite(13,HIGH); } delay(100); }

[@For_the-love_of_physics]

Oyage number eka denna puluwanda

[@mdmirajulislam1690]

.

[@idagottidivyasri771]

Pls send me the code

[@slideas1]

Code in description ,download ....

[@idagottidivyasri771]

It's not opening pls send it to me

[@slideas1]

@@idagottidivyasri771 mail please

[@idagottidivyasri771]

Mail not working pls send to me comments code

[@slideas1]

char val; void setup() { pinMode(13,OUTPUT); Serial.begin(9600); digitalWrite(13,HIGH); } void loop() { if(Serial.available()){ val = Serial.read(); Serial.println(val); } if(val=='1'){ digitalWrite(13,LOW); } else if(val=='2'){ digitalWrite(13,HIGH); } delay(100); }

[@silversurfur69]

I followed the video but my bulb didn't glow what to do

[@aljayramos5437]

can I use other type of switch?

[@최은우-d5t]

your outcome is different to your circuit diagram, in your diagram the arduino is powered by the 220V AC but in your actual circuit it's powered by 9V DC. Is there any chance of getting the diagram with the physical switch and 9V DC adapter?

[@qadeer1685]

Arduino uno Bluetooth 4 channel relay

[@danielikhmall3539]

Can we switch off the light using phone eventhough the switch button is on?

[@jb_labs]

I'm pretty sure you can. It seems both the switch and Arduino is connected to the same terminal on the light bulb, so arduino can turn on the lightbulb, regardless if the switch is off. U could think of it as a OR gate Problem is, if the light switch is on, then it cannot be turned of via the app, it needs to be done by the light switch. And same if the app is on, the app is only way to turn off.

[@lawalnasir2003]

perfect and lovely

[@polepeddibharat1315]

Bro program kinda description lo ledu bro okasari program link petava bro plz

[@dnyandeotembare5064]

4 relay program code chahiye

[@Somipra-vk6mi]

Are relay pickup nhi le rha

[@gameofdeath1731]

emergency help bro please text fast waiting for your reply

[@rKj4795]

What if we don't use adapter ?

[@Kaunderdasen1]

Do you have coding if we want to implement voice control for this exact project?

[@slideas1]

kzbin.info/www/bejne/npyyhop_q5upY9k

[@rahulshahane6383]

There is analysis in my uno r3 board , perhaps I had not been completed my project 😢

[@rahulshahane6383]

Is Unor3 is suitable for this project ?

[@djblanscky]

my bluetooth module is JDY-31 how can i do to pair it.

[@MathiTamilGaming]

What if we turn ON both the Switches ( Mobile and Manual) ?

[@slideas1]

Bulb on

[@fabma4763]

،*❤

[@Chujie28]

Hello sir can i get a new programing coding link , the link on description is expired

[@slideas1]

char val; void setup() { pinMode(13,OUTPUT); Serial.begin(9600); digitalWrite(13,HIGH); } void loop() { if(Serial.available()){ val = Serial.read(); Serial.println(val); } if(val=='1'){ digitalWrite(13,LOW); } else if(val=='2'){ digitalWrite(13,HIGH); } delay(100); }

[@jenariyak6632]

Please give me other program

[@dilshankasthuriarachchi4737]

Hi there gm is this relay module without optocoupler?

[@slideas1]

GM ,yes without optocoupler.......

[@zeeshanmuhammad1114]

@@slideas1 any vedio about to control geyser according to your timing and temperature

[@bunnyshhh3020]

Count download arduino code.🙁