Homemade CHAINSAW BIKE

[@l1nked16]

Hey I have a problem so I welded the sprocket on the outside of the clutch and I’m using the stick 7 speed on my rear wheel so when I hooked it all up I couldn’t pull start it unless I lifted the back wheel up because it was to hard because of the chain so I had to lift the back wheel up but when I did that the chain fell off cause it was loose, do you think that’s cause I need a chain tensioner?

[@ultramake]

That's probably it

[@vi23a]

you could have also tried starting it by pushing (most chainsaw clutches can whitstand a lot of braking force and still run BUT they get really hot...)

[@anci8044]

Your new subscriber

[@frigglebiscuit7484]

may have warped the clutch drum with all the heat from welding, and the clutch is now touching. just sand some of the clutch off i guess, and it should be good.

[@Rob337_aka_CancelProof]

Configure it like a mid Drive using a triple chainring on the cranks with the original chain on the inner sprocket and the one that goes to the chainsaw on the outside sprocket which means the petals will always be moving unless you can figure out a way to put a Freewheel on the front sprocket somewhere but I'm not sure how you do that and the tensioner on the rear derailleur will probably do what you need it to do because that would make a huge difference I think with the low torque and inadequate speed that leveraging the existing gears would be a game changer except when you're starting out which with the higher gear ratio would just put undue stress on the motor chain and everything else. That would also allow you to mount it inside the triangle where it would be better balanced and feel a l'ot more natural and require a much shorter chain that you probably wouldn't have to worry about coming off just an idea you may not have considered and good luck hope you get it worked out

[@b-ill2195]

You made your own sprockets... you are the man 😁

[@montimahner9357]

In all the videos at the end the saw doesn’t sound under any load. Just seems like you pedaled really fast and coasted by in the video frame because each pass was so limited in distance covered. Just saying that saw doesn’t sound like it’s under any load at all.

[@beckettevans7228]

Typical chainsaws run at around 13,000rpm, and for a 20" wheel, 10MPH is like 300 RPM so ideally you'd have a 40:1 reduction from the chainsaw to the wheel... in this (and many other videos) it looks like people us a regular 13t sprocket at the saw and a 40t sprocket at the wheel giving you like a 4:1 reduction...... That chainsaw IS idling and probably burning the clutch.

[@daber111286]

@@beckettevans7228 czyli bardzo duża zębatka na koło, a duża przy pile

[@azuosals]

Que legal ótima idéia brother. 👏👏👏

[@ibrahimkacmaz3225]

Teşekkürler🙏

[@zbuhihsnov6284]

👍👍интересные

[@jacobramirez4894]

Amazing editing and skills wow

[@ultramake]

Just watch the new clip ;D.

[@MrJosh066]

❤❤❤❤ perfect

[@chriscordray8572]

All that weight should have been lower inside the frame and just use the pedal gear thats on the inside of the pedal set of gears

[@mikkolempinen2717]

Put the tensioner to the slack side

[@земляниин]

Талант, по монтажу даже заметно👍

[@BiGMiAMiTV]

Awesome ❤

[@BlackstoneMalone]

I would have had to clean and shape my brackets! I know it works and is well designed but I would have to grind down and shape the metal and paint it.

[@chrisaskme811]

I would have made it better than yours

[@ciclotronforever]

Nice build. Your gear ratio is wat off, even worse than my first friction drive builds but I realy like your ideas ! The video montage is very nice too !

[@qualityreno9689]

Very inventive! Good job

[@motosill_garage]

Монтаж на высоком уровне!

[@mundodobetove3047]

Parabéns muitos bom mesmo Deus abençoe sempre sua vida amén 👍👇👍 Deus abençoe todos meus escritos amén 🤔😳👏👏👏👏👍👍

[@ilighencea5915]

Жирный лайк тебе! А констрцию натяжителя взял на заметку ✋ Благодарю!

[@ilighencea5915]

@Diribejcho Diribejchev ✋ я так и не сделал этот натяжитель...еду без него. Это лишняя нагрузка на мотор.. У меня д8э ,колесо задняя немецкая на 28 (3 переключения) к ней приспособил звёздочку от мотоцикла дельта... Также и цепь Пока еду, нет проблем никаких, и шпицы не ломаются если правильно с места стартануть.🙂

[@Rob337_aka_CancelProof]

Interesting gear ratio which won't result in very high speed but I wonder how it does for range (on a full tank)? Does it have enough torque to tweak that gear ratio enough for a topspeed similar to what you get from pedaling and I wonder if you configured it as a mid drive with an extra chain ring a rear derailleur and cassette that you could leverage to make up for the limitations of limited torque and top speed resulting in something much closer to a normal bike or pedaling your ass off with a nice set of legs

[@chriscordray8572]

You could have use a bicycle gear and weld in on the backside of the chainsaw clutch

[@أبوجكدار-ص6ح]

👏👏👏👏

[@josephpennington5767]

Is that the best ratio you have figured out with using the chainsaw? I'm about to try putting a chainsaw on a trike I have so I'll have the motor on the front tire so there is less wear on the motor any suggestions would be appreciated

[@istvanilosvai2962]

Why didn't you get a cheap motorcycle throttle? It would have looked better too.

[@Tech_481]

Ya or even used the brake lever or the shifter on the bike

[@1349FDJT]

People always have something better in mind. Hw many have you built

[@teammouse]

@@1349FDJT lol true

[@thatoneguythatlikesship]

​@@1349FDJT how many have YOU build

[@1349FDJT]

@@thatoneguythatlikesship zero

[@krisrx8]

How kilometres going

[@макс-б5ж5х]

Такую хрень я делал 10 лет назад. Цепь велосипеда нагревается и клинит.😂😂😂

[@reyprieto5043]

👍👍👍👍👍👍👏👏👏

[@Eer-y8z]

Is the clutch getting hotter?

[@ihsanyuksel1618]

Bizde hic bir sey yok biz nasil yapacaz bir tek bisiklet var biz yapamiyoruz beyim sizde her seyi var.

[@СергейЗадорожнюк-у4п]

Ребята оцените поршневую группу на бензопиле даже место под декомпрессор отлит качество супер

[@malinuygur1392]

Where did you find the paper for the sprocket

[@theprimous1039]

XD

[@Lrixu]

Why do you place the shoe lace?

[@Tofft706]

Where can i find the model on the freewheel?

[@krisrx8]

how much is running

[@Alb969]

How many kilometers speed?

[@ultramake]

It can go around 40kmh / 25mph, but I made too little reduction. So, a chainsaw does not have the power to start a bicycle, but it can maintain speed.

[@loicminjauw6872]

How fast does it go

[@torstentvhd4003]

Да ли бисте могли да пошаљете копију документа који сте користили за израду опреме?

[@pavlestojanovic9631]

ово нема у београду

[@gregp4744]

Can you send the model for the sprocket ?

[@brianbassett4379]

I'll wave as I ride by and your broken down on the side of some road.

[@DeluWremia71]

2мм...маловато будет. Хотя бы 4мм.

[@cesarlopezortega8657]

Y el reductor ?

[@anonymously241]

What is the top speed? 👩‍🔧

[@kahshsnaja]

The gear ratio is wrong You need to put a smaller gear on the front and a really big on the back

[@ultramake]

Yes, I was wrong about that.

[@robertcranga9265]

Si fumul unde se duce?🤔

[@celialima1891]

Y la bujía la quito y ya no la pudo allí que pasó?

[@ultramake]

Quité la bujía para bloquear el pistón. Después de eso, devolví todo como estaba.

[@тарасищук-д4я]

Невірю ,що він поїхав.То можливо з горбачка ,або накатом.Передаточні розрахунки не ті.Ведуча зірка завелика ,а ведома замала.Оберти бензопилки високі.Я не писав би якби не знав на своєму шляху.

[@ДмитрийЧеревко-у1в]

Перевести на русский.

[@krisrx8]

How km

[@ultramake]

I don't know, I didn't measure speed.

[@krisrx8]

Ok thanks

[@krisrx8]

It is going full speed

[@krisrx8]

40

[@krisrx8]

30

[@codybarnes8335]

🤔 this is sus I'm calling baloney

[@pavlestojanovic9631]

то срби

[@ultramake]

Нећемо националистичке испаде пајо

[@JuanCarlosBarreraBautista]

Speed? 40m/h mmh?

[@benderzadunaiskiy9957]

Пилосипед

[@ernestoalvarez9963]

1q

[@andreilyshkin8211]

Возле машины по чаше вари