Thanks, I've been thinking about this since my uncle told he's been making his own fuel since he was 12 flying u-control planes in the 50s.
@thebug40463 жыл бұрын
Get a quality race grade methanol and a quality Castor oil as well this is just a last resort if you can get nothing else with the drugstore oil it's very hidden miss sometimes it will work sometimes not you will end of wasting a bunch of stuff
@jackjuhasz533 Жыл бұрын
a motorcycle mag in the 70's tested all the two stroke oils and castor oil was the best ! i raced b open enduro karts using blendzall. worked perfectly ! thanks for the new look at this amazing oil !
@thebug4046 Жыл бұрын
I run blendzall all the time it's one of the best oils I have found! 👌🏻🍻😎
@fps886797d3 жыл бұрын
I've had some really good times with this stuff, But as a nitro newbie with much to learn it can be very frustrating. A bit of advice: have a good engine to begin with, one that has almost no trouble running on nitro. Fresh bearings, good gaskets, hot glow plug and you'll be in for a pleasant surprise. I sure was...thanks Bug.
@thebug40463 жыл бұрын
No problem! Thanks for watchin! I do have a rc group on Facebook nitro/diesel/gas rc and more if you want to check it out just 2questions i will add you in lots of great guys in their and no BS
@Alt.F4.8 ай бұрын
My go to guy for all my RC needs. Thank you! ❤
@thebug40468 ай бұрын
No worries buds just use a better oil like klotz super techniplate oil. Food grade castor oil is a last resort if you absolutely cannot get anything else
@richardgordon-davis70710 ай бұрын
You can tell your Friend in the UAE that instead of Nitro Methane he can use acetone up to a max of 5% which gives the very same benefits as low nitro content fuel, ie easier tuning ,idling, throttle response and starting. I does NOT however work as a fuel booster. I use it in my aeroplanes.
@thebug404610 ай бұрын
Yup I told him that not long ago. Seems like it's working for him
@titodiaz64869 ай бұрын
So instead of methanol you use a acetone
@thebug40469 ай бұрын
@@titodiaz6486 it won't work. Methanol is what holds the catalytic reaction with the platinum on the coil of the plug. Acetone is believed to help with turning stability
@AlexandrosArt Жыл бұрын
Thank you so much you the best. 2 years later but still good info
@thebug4046 Жыл бұрын
Your welcome! 🍻💯
@FargothPLАй бұрын
I would like to confirm that it works. I did the tests on a modified Vertex VX .18 with the 3rd window unlocked. I don't know if it's because of the low temperature or the fact that the model had been sitting unused for a year, but it wouldn't start until I heated it up thoroughly with a heat gun. The engine works, but it sounds "heavy". The smell of the exhaust fumes is also a bit different. The model itself is not as "responsive" as on 20-25% nitro... but at least it works :) I used Castor oil for speedway motorcycle fuels (Puroline, beautiful royal blue color) and an N3 glow plug (HSP)
@thebug4046Ай бұрын
that's why I mentioned its last resort if you can't get anything else. Like here no more nitro in my area I burn 0% often but with a different oil that performs better. With tuning and compression adjustments it can perform pretty close to 10% nitro
@FargothPLАй бұрын
@@thebug4046 Not necessarily. In Poland (EU) we still can buy 16% fuel, but it's simply expensive. Many aircraft modelers make their own mixtures, because it's up to 50% cheaper than (0%) ready-made ones and they're sure of the proportions. It's worse with the availability of nitro parts and accessories... Every year the prices are higher, and the availability is lower :( BTW. I came across a guy on YT who showed how he makes his own fuel for his plane. He added 100 ml of acetone to 5 l of methanol. He said it serves as a stabilizer, so the oil doesn't tend to separate
@thebug4046Ай бұрын
@@FargothPL I did try the acetone added all it did was destroy the fuel system and add no benefits unfortunately but if you can get pure Castor oil and mathenal that's all you need for airplanes it's an 80/20 ratio by volume
@adr20sv3 жыл бұрын
This chanel should have more subscribers, keep the good advices coming!
@thebug40463 жыл бұрын
Thanks man! And maybe one day
@NitroFreak3 жыл бұрын
this stuff right here i love guys like you bug testing stuff and proving the not normal stuff sometimes will work great vid bro this was awsome
@thebug40463 жыл бұрын
Thanks man! And I got a few questions about it and that ass that called me out on it so I was like well! Time for another video or 3 haha and this is why I love this hobby All the experimentation and kind of mythbusting about stuff and showing ways around fuel if you can't buy it
@NitroFreak3 жыл бұрын
@@thebug4046 people hate on guys like you doing this stuff because u got it to work and the hater didnt thinkof it to many nay sayers and not enough to try and do it type people lol
@thebug40463 жыл бұрын
@@NitroFreak i 100% agreed man! Guy was Going on saying why not just do things the normal way and add fuel and go and my reply back wise obviously you don't understand the point of my channel because experimentation here this key if you want to watch someone just adding fuel and going there are millions of other videos on KZbin about that if you're gunna come here just to company about it scram! Lol
@martinguerra71073 ай бұрын
Thanks 4 share ur special mix.. I’m overseas and traxxas fuel here in Argentina is very expensive and castor oil and methanol is very cheap and easy to buy it… I’m trying this mix
@thebug40463 ай бұрын
Glad it helped ya! Use OS LC3 glow plug and remember to mix by fluid ounces 😎
@elizabethtores18693 ай бұрын
WHERE YOU BUY METHANOL IN ARG?
@thebug40463 ай бұрын
@@elizabethtores1869 ARG? where is that?
@CustomBuiltDIY Жыл бұрын
Have you ever tried to mix methanol and two-stroke oil mix like sthil full synthetic two-stroke mix?
@thebug4046 Жыл бұрын
Dose not work. You need klotz castor oil or klotz super techniplate oils they are designed for that. This is with drug store castor oil is last resort fuel people that cannot get those oils. I have many other videos explaining it
@vyaraalarie9 ай бұрын
im curious, what's your opinion on VP powermaster fuel? all my hobby store stocks is traxxas top fuel and powermaster master basher 20%
@thebug40469 ай бұрын
The master basher is better than top fue. l but still way to much oil. Basher fuel is solid to people that don't know what they are buying.
@vyaraalarie9 ай бұрын
@thebug4046 I see I see. I talked the owner into ordering the 9% oil variant of the vp fuel, and he also ordered some sidewinder fuel. Here's hoping it comes in soon
@thebug40469 ай бұрын
@@vyaraalarie right on
@andrewwilliams3394 Жыл бұрын
So i have been using this 0% nitro fuel for bashing for a month with great success. My next goal is to find a replacement oil for "air filter oil" which is grossly overpriced for rc use. ANY SUGGESTIONS ?
@thebug4046 Жыл бұрын
Lucas air tool oil or you can mix it 50/50 with ATF works great for after run oil and motocross air filter oil from bel ray is what I use
I’m confused, how are you making fuel without nitro and could I use it on a Traxxas record 3.3? Will it go very slow and affect anything?
@thebug40466 ай бұрын
Well to twist your mind a little bit there is no such thing as a Nitro engine they don't exist what you're seeing made in the video is what's referred to as glow fuel which has just 2 ingredients these engines do not require Nitromethane to run. And yes I have several videos running 0% nitro in 3.3 engines you will need an OS LC3 glow plug klotz super techniplate oil and methanol. In a 90/10 mix all mixtures will be done in fluid ounces. Very important. You will need to tune a little bit leaner and make your idle gap bigger and that's about it. It won't make as much power as 20% nitro but still plenty power for bashing.
@yoster7711 ай бұрын
This is super cool, but I wish it was cheaper. I can't seem to find a gallon of Methyl Hydrate for less than $30 or so. About the same exact price I can get 1 gallon of Nitro from the hobby store.
@thebug404611 ай бұрын
Yeah it's really not worth to do this it's basically a last resort if you can't get anything else. Like a guy i talk too in Egypt it's illegal to have nitro in any % so they burn 0% nitro over there
@trevor52905 ай бұрын
I used paint thinner from big box store. Pretty much the same as Methyl Hydrate in fact it is MH. Only$17CAN per gallon.
@crazynitroeverything44823 жыл бұрын
I've been doing something similar. Using 30 percent nitro 23 percent oil heli fuel. Add 50 percent methanol and a tiny bit of castor. Makes for a good basher fuel 15 percent nitro 12 to 14 percent oil.
@thebug40463 жыл бұрын
No as long as it works
@MehmetSutas2 жыл бұрын
Can 2 stroke engine oil be used instead of castor oil
@thebug40462 жыл бұрын
Nope won't work. Unless it's klotz castor oil or klotz super techniplate or maxima 927
@Troubledboy882 ай бұрын
You ever experiment with nickel plating a worn out sleeve? I recently did a DIY pinch and it worked really well, so I don’t want to mess with it yet. I saw a guy plate his piston on here, but that seems nonsensical to me, as the friction would be far higher. I have been nickel plating for a little while but never tried a sleeve so I’m curious
@thebug40462 ай бұрын
Most of the sleeves are brass with Chrome plating a lot of old ones were nickel plated I haven't tried experimenting with plating yet but at something I might look into in the future we will see. 🍻😎
@Troubledboy882 ай бұрын
@@thebug4046 good to know! I don’t know how well nickel would plate over chrome. Might muck it up🤣
@thebug40462 ай бұрын
@@Troubledboy88 they have been using nickel plating for years but it does require higher Castor oil for sheer strength in the fuel witch will make it last much longer
@WaschyNumber1 Жыл бұрын
Does Castor Oil go bad if it is mixed, or is it possible to store it than infinite?
@thebug4046 Жыл бұрын
As long as it's captain an air tight container it will last basically forever. When you mix racing Castor oil with methanol or gasoline and it gets cold enough and can separate so occasionall you want to shake your fuel to be sure that it's thoroughly blended.
@WaschyNumber1 Жыл бұрын
@@thebug4046 thank you very much
@thebug4046 Жыл бұрын
@@WaschyNumber1 no worries
@edwardsedgley17146 ай бұрын
So I'm an aircraft mechanic and we have a ton of unused Eastman 2380 jet turbine oil and it is pretty high in viscosity. Do you think I could use that instead of castor oil. I've always was curious.
@thebug40466 ай бұрын
Great question! To be honest with you I have no idea but you could always try to mix some with methanol say a few ounce of each and see what happens. if it's petroleum-based it will separate. And won't mix. Klotz super techniplate oil is what you want a good oil for making glow fuel. Definitely update me on how it goes! 😎🍻
@edwardsedgley171421 күн бұрын
Howdy! Long time man! . So I mixed 2380 with some VP racing fuel to see if it will mix and not separate. And.... It mixes perfectly! I'm now planning to truly make it. Nitro fuel mixed with jet turbine oil works as of now lol@@thebug4046
@thebug404621 күн бұрын
@@edwardsedgley1714 I wouldn't suggest it as it's a very thin oil and might not have enough film strength witch will result in engine damage. The oils used to make rc fuel are 60w usually and have a certain sheer strength. But if it mixed try it in an engine that you don't care about. Just something to keep in mind
@edwardsedgley171419 күн бұрын
@@thebug4046 absolutely agree. I'll definitely test it out here soon. I'll let you know how it goes on a bench test
@andrewwilliams3394 Жыл бұрын
Hello There, i gave up Nitro RC (Truck bashing) because of the cost of the fuel so was interested to see your video, so i have set up an old engine on a test bed and am off to home depot to get methanol, i have caster oil, i have a couple of questions, 1. what plug would you recommend its a force .26 engine, long reach plug. 2. how should i change the needle settings from the regular settings before trying to start. OH by the way there were two .009" shims in the engine. I have removed one of them. 3. How to clean up internals of engine after running to prevent gumming up. Thx in advance Andy
@thebug4046 Жыл бұрын
this is a last resort fuel if you literally can't get anything else. what I would suggest doing is getting klotz super techniplate oil It won't varnish your engine and it tunes a lot better just keep in mind as fuel does not tune as easily and is more sensitive to weather. Run a hot glow plug OS LC3 and pull a head shim or two depending on how many are in their. If it has 4 pull 2. It's 13oz fluid ounces to a a gallon of methanol. Food grade castor oil can have other stuff in it and you will have to clean your engine a lot or it will get to sticky to run. Also we pay 70 a gallon for 30% nitro i run mostly small block engines so i don't burn a lot of fuel. Klotz super techniplate oil is available on Amazon or ebay if you live in the USA. Maxima castor 927 works great as well as blendzall original green label castor oil And the needle settings will probably a lot leaner but you will have to tune for your environment it will be different for me than it is for you
@andrewwilliams3394 Жыл бұрын
@@thebug4046 using maxima 927 castor and home depot methanol works out to about $12.00 CAD for a quart thats half price compared to 20% nitro. so if it runs ok i will be happy. Have just watched your video of you running a buggy on this fuel and it seems to run fine. I am only bashing so high performance is not an issue. one last question does it affect the life of the glow plug. Just as a side note back in England in the 60s we used to run control line planes using 0% nitro without problems. I was interested to see your diesel engines, i used to run an ED Racer on home made fuel. Thanks for all your help, keep up the good work
@thebug4046 Жыл бұрын
@@andrewwilliams3394 Good choice on oil I haven't had any problem with plug longevity and yes I used to fly control line airplanes as well with 0% fuel. You can actually buy 0% pre made at some hobby shops still It's just a little more sensitive in car engines. But for bashing and messing around it's good enough
@andrewwilliams3394 Жыл бұрын
@@thebug4046 glow motors we used to run in the 60,s were DC merlins, DC spitfires and Wenmack hotshots, things were a lot simpler back then.
@thebug4046 Жыл бұрын
@@andrewwilliams3394 that's awesome and yes I agree
@joshuadulaney5559 Жыл бұрын
How did you need a pro 15 connecting rod? They usually take it oem 😏
@thebug4046 Жыл бұрын
Because someone said i couldn't make one and I did to piss them off lol
@stephensparkman52336 ай бұрын
Nice video bug enjoyed it with a beer lol but anyways my 2.5 rustler is idling high and it’s rolling not really bad but enough to piss me off lol the idle screw is all the way out do I need to mess with the high are low speed needle bug?
@thebug40466 ай бұрын
Are you sure the throttle trim isn't holding it open? And if you are on Facebook im an admin in the Nitro RC enthusiasts group. I suggest going in and posting a video which will make it easier to help ya
@davidhill56213 жыл бұрын
I have made this fuel for my cox 049s , i put 3 drops of green food coloring in , works awesome!
@thebug40463 жыл бұрын
Food colouring isn't necessarily a good thing to add since it has water in it and saugers in it best to run without it and 80/20 mix is usually what I use
@charlessmalling99032 жыл бұрын
lol...the 049 won't run on 0% nitro. I call BS
@darrellsomers54273 ай бұрын
Will this work in my 68 Camaro street car ?
@thebug40463 ай бұрын
Probably not. Without a lot of carb jets a different oil and fuel system that is designed for methanol. Also 3mph fuel efficiency lol not worth it unless you are racing
@smokesedition883 жыл бұрын
Awesome bro awesome I have another experiment for you Denatured alcohol, TruFuel 4 cycle engineered fuel with TF3 (Ethonal Free), an 2 stroke synthetic castor oil/chain saw oil
@thebug40463 жыл бұрын
Denatured alcohol kinda works but is very hard to keep it running because it's not 100% methanol it's got a lot of other alcohols in it. And as far as true fuel or that kind of can fuel dose not work. I have tried it won't ignite
@TheFpc204 ай бұрын
I will be make my own 0% nitro after few years, on 2016 i was making my own with 0% but a friend gift me 1/2 L of fuel with 30% nitro so i'm hoping 0% work again, if not will have to rebuild the engine, also planning to use pure acetone with the mix, in my case i will use natural castor oil, do you recommend 10% or i can use 8% natural castol oil use to gumm my engine after few months of not use😂
@thebug40464 ай бұрын
Switching between 0 and 30% you won't have to rebuild the engine every time you do that just so you're aware. just tune accordingly and if you can get racing grade caster oil use that if not then use 10% by volume Pure castor oil.
@TheFpc204 ай бұрын
@thebug4046 excellent, purchased a gallon of methanol and 4oz of pure natural castor oil and pure acetone, tonight I did a mix for 60ml of fuel that is almost a tank for bu buggy, just 5% acetone, 10% oil and the rest of methanol, will be testing tomorrow, my engine has a old a3 glow plug that work ok with the 30% nitro but I have a OS 6 too, will try them both tomorrow for the 0% nitro mix
@thebug40464 ай бұрын
@@TheFpc20 A3 is the same as the os 6 And honestly with the acetone I have tried it with and without it makes almost no difference other than just eating the fuel system. And for one gallon mix go 12.8oz fluid ounces oil to 115.2 fluid ounces methanol for 10% oil by volume. If you can get klotz super techniplate oil that will be your best bet. Food grade castor oil is a last resort if you literally can't get anything else.
@TheFpc204 ай бұрын
@@thebug4046 perfect, locally only synthetic castor oil I can find is castor 927, in 16oz for $17 and 33 oz for $30, I have to try the 0% fuel on my revo 3.3 friend's truck so if it work we can buy the 33 oz and divide the mix for use it on our cars
@thebug40464 ай бұрын
@@TheFpc20 maxima 927 works good to! Much better than food grade. You can get klotz super techniplate on Amazon or eBay. If you want it. The super techniplate tunes better than 100% castor. The 927 has a synthetic mixer with it and doesn't tune bad at all. Smells good to.
@EnglishTurbines5 ай бұрын
If you buy commercial ready mixed Glo Fuel here in the UK. It will typically have 17% oil content. Choose your Nitro cintent to suit. But yes, I can remember "Straight" Glo Fuel ....NO Nitro and just 10% oil....Even 10% is too much IMO....A Glo engine will run way more efficiently on Petrol using a spark ignition and a 25 : 1 mix only....In particular a four stroke Glo engine...🤔😏🇬🇧
@thebug40465 ай бұрын
You won't see spark Ignition for RC car engines and less it's something larger 1/5 scale i have tried gasoline mix in rc car engines and will make the engine run extremely hot and make much less power. And here most rc car fuel is usually between 8 and 12% oil you can get higher 14 to 16% oil but it doesn't help anything in land engines. 10% is most common in the brands available here. Airplane fuel is usually 17 to 25% oil here depending on what engine you need it for
@EnglishTurbines5 ай бұрын
@@thebug4046 Yes, petrol is not suited for little two stroke car engines, heat dissipation is a big problem. Not so on a four stroke aircraft engine though, although the engine runs hotter, the air cooling provided it's plentiful, is fine. Timing is best a little retarded and a shim to reduce compression helps also. The end result is a clean running engine that uses about 1/3 volume of fuel compared to nitro with very little change in ultimate performance....🤔😏🇬🇧
@markwallace52742 жыл бұрын
Any performance disadvantages without nitromethane ? I would assume there is considering how much oxygen Nitro as attached to it. A lot like methanol does
@thebug40462 жыл бұрын
Yup needs high compression to advance timing
@jeboylaborte10572 жыл бұрын
what kind of methanol sir?
@thebug40462 жыл бұрын
100% methanol race grade M1 methanol
@marcusrobinson3054 Жыл бұрын
I would like to know the brand also
@aliensphyncter9528 Жыл бұрын
Where can u buy the methanol
@thebug4046 Жыл бұрын
Heet yellow bottle or find a race shop or a chem dealer. Ps it's not worth it. It cost more to make then to buy from bones brew morder sports
@royaltybadboy54653 жыл бұрын
Can make this fuel with 2 stroke engine oil or racing bike oil 2t ??
@thebug40463 жыл бұрын
Nope not unless it's ment to be mixed with methanol klotz castor oil will work
@royaltybadboy54653 жыл бұрын
@@thebug4046 thnx for the reply
@thebug40463 жыл бұрын
@@royaltybadboy5465 no problem
@Rebecca_The_Dragon2 жыл бұрын
This must by a really common swap lol. I got one of these T10's from a neighbor for free, fixed it up but the engine was roasted, ordered a new piston and sleeve but saw a Pro .15 in my LHS for 50 bucks, couldnt resist. After performing the old SquirrelOD engine seal, it holds a tune really well, just SUPER slow due to running the incorrect pipe that came with the T10, need to get a proper small traxxas pipe for it and then it will rip.
@thebug40462 жыл бұрын
That's awesome!
@redraider7614 Жыл бұрын
Wait, it’s 99.9% pure and it has water in it…will that ruin or rust up the engine?
@thebug4046 Жыл бұрын
You can't buy 100% alcohol it doesn't exist in daily life. Unless it's kept chemically dry out of air. Any methanol or nitromethane or rc fuel in general will always be 99.9% all alcohol will pull water out the air. If you have have left your fuel open for a long period of time an hour for example it has now pulled some moisture from the air. Nothing you can do about it. The only way you will rust the engine is by plugging the exhaust to shut it down and leaving it witch again pulls water out of the are and becomes corrosive. Always run your engines out of fuel until no start and they are fine to sit like that for a few months before you need storage oil aka after run oil.
@redraider7614 Жыл бұрын
@@thebug4046awesome thank you. I grabbed some HEET gas antifreeze and some castor. How much would I need for half a quart?
@thebug4046 Жыл бұрын
@@redraider7614 heet yellow bottle only! You will need enough to fill a 1qt rc fuel bottle then 4 fluid ounces castor oil. Add oil first add some methanol shake it them top off your bottle. If you are using food grade castor oil you will need to clean your engine a lot because if you let it sit the engine will get very sticky. You will need to run a hot glow plug and tune it leaner to make it run. It will be more sensitive to tuning. This is really only a last resort if you can't buy rc fuel. It's not any cheaper. If you do decide you want to run only 0% nitro it's 12.8oz oil per gallon and order klotz super techniplate oil it's designed for nitro rc engines and doesn't get sticky. It's also a lot lighter and tunes better
@moexotics52062 жыл бұрын
Great video bro 👍.. been trying to find a way for fuel . What other oil can be used for the mixture 🤔
@thebug40462 жыл бұрын
Honestly this whole thing is not worth it if you can just buy fuel at the store. it often costs more runs worse it's only if you can't get anything else. And basically oil that is designed to be mixed with methanol. Klotz castor oil Klotz super techniplate oil
@moexotics52062 жыл бұрын
Thanks for the reply thebug 404 Yeah we're I live at there is no hobby stores or a store that sells Fuel ⛽ for my nitro trucks mostly use my electric. but wanted to get into my monster truck nitros Gonna try getting the materials of Amazon see if not that pricey . Thanks thebug 404 👍
@thebug40462 жыл бұрын
@@moexotics5206 if you live in the USA you can order Bones brew fuel right to your door. 3 gallons of 30% nitro for 90 $. Trust me the 0% nitro requires a lot of nonsense to run properly like shiming and different glow plugs
@terrymunn12242 жыл бұрын
I have some 35% nitro i was using in boats and now id like to reduce the nitro level but not the oil level .Do you know if there is a mixdown formula or how i would go the process ?
@thebug40462 жыл бұрын
Not sure to be honest I can tell you one thing you will spend a lot more money trying to reduce it rather than just either burning it and something else or just buying the correct fuel Yet I try to avoid getting into that unless I absolutely have to because it's very easy to mess up and damage your engine
@terrymunn12242 жыл бұрын
@@thebug4046 ok , thanks I was able to find a gallon of 10% omega and have been mixing that 50/50 with the last gallon of 50% boat fuel I have here and it works fine .I checked the oil composition of both fuels and they were compatible so I went for it. I guess I could buy another gallon of say omega 5% if the oil content is similar and add it to my 35% and get two gallons of 20 .The 35 has been purchased years ago and still fresh and sealed but i feel i' just wasting the 35% nitro in a sport plane.Thanks for your reply.Im out east in NewBrunswick BTW
@thebug40462 жыл бұрын
@@terrymunn1224 omega 10% is 17% oil so whatever the boat fuel is your probably in the 20% oil and 45% nitro area lol not a good idea to mix them if you can help it because You can wind up with unknown percentages and it can end up being very damaging to your engine depending on how it's shimmed etc. If it's a engine you don't care about then absolutely but I wouldn't do it to anything you care about
@amputeerc92983 жыл бұрын
This is pretty badass man. Got 2 questions for ya. first, Is there anything you can safely add to the fuel to give it some color so you can see the fuel level of the tank easily? Second, what would you use for after run oil/cleaner to keep the castor from locking up your motor during storage? I'm down like a Cadillac on 4 flat tires to try this 0% hardware store fuel. I think it'll be fun to try.
@thebug40463 жыл бұрын
Just use normal after run oil or air tool oil as far as color just by klotz Castor oil or klotz super technplate it's red i will say the methanol isn't always very good mine had water in it and the oil separated out after 2 days so that was some money wasted just order race grade methanol if you can it works every time. this isn't really the best it will work if absolutely have nothing else available however I am going to see about getting some molecular saves to put in the methanol to dry it out as much as possible they Absorb water in alcohol then im gunna try it again it could have also been the oil something might have been up with it kinda the risk you take when playing with this kind of stuff ps you can buy fuel dye but it's very expensive you often have to get 5 gallons at a time about 300$ last time I checked People will tell you to put food colouring in but the problem with that is it's contains water which will spoil your fuel it also contains sugars which will burn and stick to the inside of your engine not a good idea just run without a body or pull the truck up to you now and then to see how much is in the tank
@RayGame554 ай бұрын
Thanks for sharing this video, so after 3 years from posting this video, the best homemade rc fuel mixture 90/10 ( Methanol + oil : you mentioned two brands klotz and blendzall which one best? Last thing additional acetone 5% ?
@thebug40464 ай бұрын
Use a quality oil like klotz super techniplate at 10% oil by volume or 12.8oz fluid ounces oil to 115.2 fluid ounces methanol for 10% oil hot plug. Don't waste your time with ass at tone it makes no difference other than destroying your fuel system
@ASDJHVCGASDJHCVG Жыл бұрын
Great video. So what percentage oil do you recommend now? Seems like you've had some time to test this. Since the engines run leaner with no nitro, there's less fuel running through them so wouldn't a higher oil content be needed? Or it seems ok at 10%? I saw your videos running 4%-20% oil. Thanks for any help
@thebug4046 Жыл бұрын
All the other videos were just what I had on hand that was already mixed. I usually always run 10% in anything that isn't a ABN sleeve or airplane engine. ABN sleeve engine i run around 15% oil airplane engines 20% oil all ABC engines 10% oil
@AmericanDefender2 жыл бұрын
Interesting fact. Castor oil comes from a gland in a beavers butt. So our cars and trucks run on beaver juice!
@thebug40462 жыл бұрын
Nope. it actually comes from a plant. I used to grow organic castor plants years ago for oil for health and food protection. A quick Google search will show you what a castor plant looks like often quite big plants
@thebug40462 жыл бұрын
There was another thing about vanilla coming from the anal glands of a beaver it's been floating around for years but it's bullshit haha
@AmericanDefender2 жыл бұрын
@@thebug4046 here's the process. kzbin.info/www/bejne/iKiyqmCPaZ2qodU
@DroneFox1 Жыл бұрын
You're probably thinking of castoreum.
@marcusrobinson3054 Жыл бұрын
I don't think so
@noppadonbuaban45993 жыл бұрын
use with rc plan engine Can you do 4 strokes?
@thebug40463 жыл бұрын
Yup 80/20 max
@noppadonbuaban45993 жыл бұрын
@@thebug4046 no nitromithen
@thebug40463 жыл бұрын
@@noppadonbuaban4599 it's not needed for these engines to run as they are not nitro engines they are glow engines Which run on glow fuel which is just too ingredients methanol and Castor oil. Nitromethane is added to increase timing and performance but is not necessary. There is really no such thing as nitro engines
@noppadonbuaban45993 жыл бұрын
@@thebug4046 Thank you very much. I'm just learning to play. I didn't know this at all.
@noppadonbuaban45993 жыл бұрын
@@thebug4046 i just got leo 15 and thunder tiger f54s
@EnglishTurbines5 ай бұрын
Nitro Methane is an oxiginator and helps the Methanol burn faster making more power. Its not essential though because its the Methanol which reacts with the glo plug element and keeps it glowing. ...🤔😏😏🇬🇧
@thebug40465 ай бұрын
Yup! Exactly how it works. This is more or less something that people were asking me about if it were actually true and yes it is. Since nitro is illegal in some countries they have to burn 0%
@jmaclaren41473 жыл бұрын
I get castor from Sig, mix it wi Methyl Hydrate from Canadian tyre. I use it in ma four stroke engine wi nae problem.
@thebug40463 жыл бұрын
Nice! I haven't seen sig oil in years where you getting it from?
@jmaclaren41473 жыл бұрын
@@thebug4046 Great hobbies, I bought 2 four liter jugs.
@VintageCR3 жыл бұрын
ok so, 0% nitro -does this effect the general/total performance of the engine?
@thebug40463 жыл бұрын
It's not as fast it will tune different it likes a hot plug and a little more compression in so engines if set up right it can run just about as good if you know what you're doing ps use good quality Castor oil like klotz It's much better and doesn't get sticky
@VintageCR3 жыл бұрын
@@thebug4046 thanks man! so, do you know a castor oil called "Eurol Racing" (its usually used for 2 strokes) and is called a 'racing' oil. this one also burns well with methanol, alcohol and normal car gas like diesel/E10. im wondering if this castor is going to work for mixing. its pretty much the only castor i can get apart from hardware store castor oils.
@thebug40463 жыл бұрын
@@VintageCR As long as the oil your getting is specified for use with methanol 2 stroke fuel than your fine regular 2T oil will not work you will ruin your fuel Castor oil is often fortified by different companies for use with racing it's quite common in husband for the last 80 years
@locknut7869 Жыл бұрын
Nice mate thanks i will try it
@thebug4046 Жыл бұрын
Don't waste your time or money. It's really not worth it if you can't get normal nitro fuel. But it's fun to mess with
@PaggiPlumbing2 ай бұрын
Holy shit i have to show this to my buddy we were talking about how outrageous the cost of fuel is around here and its not close by
@thebug40462 ай бұрын
Go with klotz super techniplate oil. It's much better. using drugstore Castor oil is a last resort. I will have to crush your expectations as this does not cost any less than just buying pre-made fuel if you live in the US. this is something we do when we can't get anything else as fuel here is 90$ a gallon and no longer available in my area. If you can get methanol and klotz super techniplate oil cheap go for it! It doesn't make as much power and is more sensitive for tuning but if it's all you got it works. Pretty good
@thebug40462 ай бұрын
Go with klotz super techniplate oil. It's much better. using drugstore Castor oil is a last resort. I will have to crush your expectations as this does not cost any less than just buying pre-made fuel if you live in the US. this is something we do when we can't get anything else as fuel here is 90$ a gallon and no longer available in my area. If you can get methanol and klotz super techniplate oil cheap go for it! It doesn't make as much power and is more sensitive for tuning but if it's all you got it works. Pretty good
@jongonegone12623 жыл бұрын
no temp gun needed. just keep your fire exstingusher close by.
@thebug40463 жыл бұрын
🤣🤣🤣
@nitrogas57193 жыл бұрын
Huh, little did I know that you can make fuel out of stuff from the hardware store😂
@thebug40463 жыл бұрын
If you got absolutely nothing else then yes you can!
@joserribera488811 ай бұрын
Where can I buy it
@thebug404611 ай бұрын
I don't know where you live so I can't really help you. You need methanol and klotz super techniplate oil mixed 90/10 but honestly it's more expensive and harder to tune. Not worth it unless you have no other choice
@glowiever3 жыл бұрын
so how has it been? rc running well?
@thebug40463 жыл бұрын
Yup runs not bad
@samsara33623 жыл бұрын
Hey bro I've been watching you for awhile I was sent down this way from hybrid really love to channel I live out in the country and Nitro is crazy to get one gallon of nitro up here cost me over 100 Canadian dollars so I'm looking to make this exact mix any tips on maintenance and things I should look for
@thebug40463 жыл бұрын
The mixture itself is very easy I will say to use an actual good quality Castor oil instead of the stuff from the drugstore because it could separate and it gets very sticky overtime it's not really the best thing it's a last resort you want klotz super technplate or klotz Castor oil Now you can use the methanol from Canadian tire it's often not the best but it works if that's all you can get optionally if you can get racing grade methanol it's more pure and much better you also will need a hot glow plug depending on your engine will either B and OS LC3 or OS A3 The tunein will be more sensitive to weather change but if you know what you are doing it's not really that big of a deal oftentimes in you 1st start with 0% the settings will be extremely rich and you will need to lean it out some Another option is if you do have a bottle of store bought fuel is just add smalle amounts into your 0% mixture for better tuning using it like an additive The oils both can be found on eBay or Amazon they are a little bit pricey but definitely worth it Hopefully that helps I did make another video explaining most of this
@samsara33623 жыл бұрын
Thanks I am going to get the klotz but I'm looking at a long wait before I can get it until then I will be trying your castor oil from the hardware store with methyl hydrate do you think if I run a tank of 30% Nitro after using this it would help the engine clean itself out I'm just wondering I'm experimenting looking to find the cheapest most efficient way to run my Nitros
@thebug40463 жыл бұрын
@@samsara3362 Yeah go for it but I will say what you can do is just run frequently and will keep it from getting sticky if you park it for say a week at a time at least used some sort of after an oil even Little bit of transmission fluid will be OK
@sallusam63682 жыл бұрын
Can I use 80/20 for my rc plane engine?
@thebug40462 жыл бұрын
Yes you can but it's not any cheaper and this is last resort fuel which means that you're gonna have to clean your engine like crazy and it's not gonna run all the best just burn store bought fuel if you can or at least switch out to a different better oil like klotz super techniplate oil
@rosinarulitasari9935 Жыл бұрын
where is the trial result of 0 nitro?
@thebug4046 Жыл бұрын
I have several 0% videos. It's a last resort fuel if you can't get anything else
@chrissolo84723 жыл бұрын
By chance What is the 90/10 or 80/20 mixture ? Asking cause I'm a beginner at mixing and making homemade fuel for nitro cars. This is quite interesting and beneficial info
@thebug40463 жыл бұрын
90/10 for cars and trucks 80/20 for airplanes they is absolutely no benefits going higher than 12% oil for rc cars also don't use what i was using for oil it gets very sticky this was a just for fun video or only if you can't get anything else use a good quality oil like klotz super technplate it's ment for rc engines if you are going to be adding nitromethane the mixture will be 60% methanol 30% nitro 10% oil. Or 70% methanol 20% nitro 10% oil
@aliensphyncter9528 Жыл бұрын
U can fill the tank up with wd 4o an it will run
@thebug4046 Жыл бұрын
No
@aliensphyncter9528 Жыл бұрын
@@thebug4046 I'm not saying do it, just saying u can, annit will run
@thebug4046 Жыл бұрын
@@aliensphyncter9528 good way to ruin your engine in a short amount of time. But if you're playing with a junk engine go for it
@bullitanaconda2 жыл бұрын
Where can i get the nitro
@thebug40462 жыл бұрын
I can't really help you with that depending on where you live it might be even illegal like it as here to buy 100% pure Nitro.. this process is only if you can't get any fuel at all! It's absolutely not worth your time or money. This is what is called original glow fuel nitromethane is not required to make these engines run. But again it's not cheaper and with drug store castor oil you have to clean your engine all the time because it gets sticky
@хабибчемпионММА3 жыл бұрын
Can I put little bit perfume in it?
@thebug40463 жыл бұрын
No it doesn't work like that. It will ruin your fuel because it has water in it. The burning Castor oil already smells good
@хабибчемпионММА3 жыл бұрын
@@thebug4046 thanks
@ninja-mz6fv3 жыл бұрын
Do it run on 2.5r traxxas engine
@thebug40463 жыл бұрын
Yup
@WaschyNumber1 Жыл бұрын
I'm looking for a method to make Castor Oil infinite long lasting, that's it not getting bad ever, not for human use but more for rust protection ect. Maybe mixing it with alcohol, ipa alcohol or ethamol or methanol, stuff that's budget friendly. 🤔 🤗
@thebug4046 Жыл бұрын
IPA alcohol doesn't work. Not the correct type of alcohol. You need methanol. And you don't need all castor oil you can use klotz super techniplate oil witch is 80% synthetic 20% castor oil.
@TexasHill3 жыл бұрын
Can you add this home made fuel to 20% nitro fuel ? At 50/50 ratio for 10% nitro?
@thebug40463 жыл бұрын
You can but cut back on the oil because to much oil isn't actually doing you any favors you really don't want more than 12% oil if you can help it. This is a last resort fuel if you absolutely cannot get anything else. Avoid the drug store Castor oil it falls out of suspension sometimes or won't mix well with other oils and you will ruin your fuel. If you run say klotz super technplate and a race grade methanol it works pretty good you can go with 8% oil and use your 20% as a aditive if you want or since your in Texas order bones brew on the internet and you can get a hold case to your door for 95$ ps avoid Traxxas fuel its garbage same with any basher fuel is garbage stick with a race blend.
@TexasHill3 жыл бұрын
Awesome! Thank you
@thebug40463 жыл бұрын
@@TexasHill no problem
@everythingrc65043 жыл бұрын
Can you brew up something that smells like fries? If youre' going to be rich might as well smell tasty!?
@thebug40463 жыл бұрын
This smells like deep fried foods
@stevennelson57613 жыл бұрын
Soo sick man I wanna try the klotz and meth mix
@thebug40463 жыл бұрын
It's easy and cheap i see lots more of it popping up in the Nitro group it will be the same 90/10 mix
@aliensphyncter9528 Жыл бұрын
With nitro at 4p bucks a gallon ill be making my own,or making all my nitros into electric
@thebug4046 Жыл бұрын
You can order 3 gallons online if you live in the estates from bones brew motorsports for a 95 bucks as a lot cheaper than trying to make it try to make it will cost you 5 times as much
@joserribera488811 ай бұрын
All the ingredients
@thebug404611 ай бұрын
Watch the video i expanded it
@joserribera488811 ай бұрын
Name
@thebug404611 ай бұрын
Methanol and castor oil. Race grade castor oil is recommended. Food grade will work but will gum your engine up
@grahambate33842 жыл бұрын
I just going to say Klots castor oil is degum and you say it.
@thebug40462 жыл бұрын
Yup. It is. Much better choice then the stuff in the video witch is a last resort if you can't get anything else
@grahambate33842 жыл бұрын
@@thebug4046 old guy at my club swear that U can put 5 to 10% petrol in the mix instead of nitro. I try it one-day
@thebug40462 жыл бұрын
@@grahambate3384 I tried it and it doesn't work it just separated as Petroleum dose not mix with methanol. It's like oil and water. And it eats your fuel lines and gasoline requires very lean tuning compared to glow fuel. So I would say he is full of shit.
@grahambate33842 жыл бұрын
@@thebug4046 thx, it sound to good to be true
@thebug40462 жыл бұрын
@@grahambate3384 yup. I did the tests years ago and it was nonsense
@loganhogan9533 ай бұрын
i tried to watch you for 4 minutes but you couldn't get to the point, sorry