Hey Maverick. It was good to see someone use an arc welder, and can actually weld. Anybody can mig. Good job. Peace
@MaverickProjectsOfficial4 жыл бұрын
Its AC stick welder and its about 20yo. Its hard to work with it . Difficult to start sometimes need many hits sometimes stop and more but ok its work..... btw I will buy a new dc stick welder soon. Thanks for your comment dude!
@notgivennotgiven77764 жыл бұрын
@@MaverickProjectsOfficial I've got my dad's old buzz box. I always liked welding with it. It's a Montgomery ward, so that tells ya how old it is. This one has a slide controller for the amperage, so you can put it were you want. I like that feature. Happy building
@MaverickProjectsOfficial4 жыл бұрын
Ac welders its forever .... Dc welder is recyclable!!
@engr.bhatti90793 жыл бұрын
We admire such technologists " Jogaroo Engr. " . Aso pls demo hose and compressor connections
@ulfurinnn4 жыл бұрын
Wow thanks so much for the vid. Im looking to build a sandblaster like this as im way tired of the small handheld one which I have to constantly shake to get any sand out. Now I just need to see if we got any old gas tanks laying around I can use.
@roththana99933 жыл бұрын
Thanks you so much for you contribution. 🤩👍
@vintagetiger20594 жыл бұрын
Great job man ! I'm going to make one . Thanks for posting
@eliseogomez1944 жыл бұрын
wff
@eliseogomez1944 жыл бұрын
lm
@EOTG_AK4 жыл бұрын
Missed the opportunity to sand blast the diy sandblaster 🤯
@blacksea694 жыл бұрын
Hi Could you precise all the dimensions of the tubes you used ? It would be very kind from you!! Another question : where did you find the big piece of tube and the tap used to fill with the sand??? I've never found any on the web😱😱 I saw tones of videos about that but your sandblaster is in the top 3 for me thanks to the simplicity and all the "options" like the protection for the pressure excess or the manometer etc
@TheZafek4 жыл бұрын
Great job. Tell me please how long this fuse nozzle works?How long can you sand on it? What is the 6, 10 or 16 amp fuse?
@pawe30304 жыл бұрын
I think its no difference between 6/10/16 amp fuse, its the same size only wire inside have different diameter for right amp :)
@TheZafek4 жыл бұрын
@@pawe3030 A to może po Polsku napiszę bo chyba krajany my sa:,-) a na jak długo wystarcza to piaskowanie taka dysza? Nie zużywa się szybko?
@pawe30304 жыл бұрын
@@TheZafek Sądzę że kilkanaście roboczogodzin. Takie bezpieczniki grosze kosztują więc to żaden problem wymienić nawet co tydzień :)
@jr04924 жыл бұрын
Porque lijas la máquina si se supone que la máquina es para eso, QUE INTELIGENTE, no te alegres ESTOY SIENDO SARCÁSTICO!!!!!!!!
@carlosm332 жыл бұрын
Todo bien pero porque no aplico el sand blasting al tanque con la misma arenadora
@zaynulserg Жыл бұрын
Когда я сделал пескоструй, первое что я очистел сам балон. И потом покрасил
@buder51164 жыл бұрын
do you connect the conpressor to the T pipe above ?
@Steffose4 жыл бұрын
good job :) 1/2 or 3/4 ?
@e.sgarage5758 Жыл бұрын
What h.p compressor did you use
@MaverickProjectsOfficial Жыл бұрын
Im using 2hp and 200lt air compressor.
@simonloveless18234 жыл бұрын
Is this easy to make may i ask,?
@justhinejohnmonton51763 жыл бұрын
Hi sir, may I know the names of materials needed to this 😁 If it's okay to you 😊
@BikesGarage4 жыл бұрын
I want this
@Mlito693 жыл бұрын
Why i didn’t he use the sander itself to sand the tank before spray painting it? Lol
@asandrxxx4 жыл бұрын
Hey. What diameter does the electrode have? What current strength did you use?
@nikahmad76204 жыл бұрын
Hi meverick.very good job. May you list what size of pipe used n other thing has been use to make this sandblasting?
@GrayHog4 жыл бұрын
If only you had a sandblaster to clean the old paint and rust off your tank!!! 😂 Just messing. Nice work.
@northlandtrucks16873 жыл бұрын
Awesome design man! What sizes of fittings and valves did you use?
@bethlangkamp65664 жыл бұрын
Great job, it’s always satisfying to make something out of nothing with your hands and talent no matter what the cost is! Usually make better product also! Thanks again keep up good work.
@simmosgarage57143 жыл бұрын
Great idea, I'm going to be building one of these. Would it have been better/ easier to use the blaster to take the paint off the gas bottle.
@mattyj3093 жыл бұрын
Man, I haven't seen someone lay down beads that nice with a stick welder in years. My father was an old school fitter and turner who taught me how to stick weld, still can't get em that clean.
@joryzhao80423 жыл бұрын
www.amazon.com/Carbide-Sandblasting-Sandblaster-Abrasive-Replacement/dp/B08QN1QSGP/ref=sr_1_57_sspa?dchild=1&keywords=sandblaster%2Bnozzle&qid=1610607075&sr=8-57-spons&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUEyQU5BMEZPRDFNRVU1JmVuY3J5cHRlZElkPUEwOTQ3MDM3NVZIRkwwMko3VUhEJmVuY3J5cHRlZEFkSWQ9QTAzNTk5NjgzTlpUQVRUT05MU0M4JndpZGdldE5hbWU9c3BfYnRmJmFjdGlvbj1jbGlja1JlZGlyZWN0JmRvTm90TG9nQ2xpY2s9dHJ1ZQ&th=1 this sandblaster boron carbide really helped me a lot, share with you,hope it can be helpful to u!
@Bigyin19633 жыл бұрын
Hi Maverick, Do you have a list of the parts needed to build the blaster ie. 1. gas bottle. 2. gadgets etc...
@jacobmorrill5557 ай бұрын
If only you had a sand blaster to blast that old tank :)
@joserribera4888 Жыл бұрын
What stick size you use and at what amps ?
@LondonCarnaval4 жыл бұрын
It shame that we have to do lot of guess work as you didn't thoroughly explain how the system is going to work and the safety in place. Really disappointing as the video itself was awesome. Now I have to go and search more videos to gather more information. It's like giving hungry cat a fish suspended high up in clothes line 😲🤔😟🧐🥴
@brucebonkowsky94064 жыл бұрын
Nice job 1 question why did you not use rusteolum hammerite paint it give your tank a nice finish and if you scratch or sent SPRAY covers most deep.scratches I did my so compressor
@dunpamy30914 жыл бұрын
I have one question...where is the air intake ...I don't. See compressed air entering
@imaverick20004 жыл бұрын
I am pretty sure that the supply disconnect is in the front on the right. You notice he put a "T" fitting on the front to pressurize the tank and ran a hose from there to the bottom "T" to pick up the sand and ran the discharge hose out the back between the wheels. It looks like the discharge hose is coiled up on top in the very last of the video. I would use a male quick-disconnect so I could just use the same hoses i use for everything else in the shop. The only thing I would change is to put the shut off valve on the quick disconnect side so I don't get the spew of air when you disconnect. Also I would put a 20 micron water trap on the supply side. You can pick up one for about 20 bucks at home depot or sears., sorry lowes. Damp sand doesn't work well at all. I also use play sand and run it through a screen. I made a screen funnel and placed it in the top. It is a whole lot cheaper than grit and easy to re-use, just filter it again. Hope this helps. If I am wrong, please feel to correct me. Please be sure to use a respirator and face mask. The sand dust is just as bad for your lungs as asbestos. I just buy the paper suite at HD and when done throw it away so I don't get sand dust everywhere. When done just blow down and remove the suit. that way you don't breathe the dust when you take your mask off.
@dunpamy30914 жыл бұрын
@@imaverick2000 thank you your valuable reply..I will look into it.....thank a lot
@davidbolha2 жыл бұрын
Those stick welding skills are awesome m8 ! 😍😏👌👍
@engr.bhatti90793 жыл бұрын
Good idea. We admire such technologists ' Jogaroo Engr. " after Jigs /Fixtures.
@ali_d67 Жыл бұрын
کاربیست
@bill53uk3 жыл бұрын
bad idea to put airline from bottom because water builds up in the bottom from the air and mixes with the sand for sandblasting
@pablosanelli42413 жыл бұрын
Nice sand blaster. I have a single piston compressor. Do you think it will work? Or it's too slow to raise the working pressure
@tharushanavinda702924 күн бұрын
What is the capacity of the air compressor needed here?
@chris-zg2sz19 күн бұрын
200 litre ok used to have one of these sand was very soar on the valves wore holes on the sides of them
@Blaaggarding3 жыл бұрын
Why didn't you actually blast the blaster before you painted it instead of sanding it by hand 😅. Great job
@BikesGarage4 жыл бұрын
Thanks for sharing this informative and useful video
@fordmustang90lx4 жыл бұрын
Hi what kind of rod did you used a 6011 or 7018 for that nice projet
@jesusreyes74763 жыл бұрын
You can use 6010 for root pass and 7018 to fill
@brucebonkowsky94064 жыл бұрын
Might used some hose on your HANDLE I was thinking cheap that floating snake
@Dysturbed-004 жыл бұрын
*Fast forwards to see if this guy is building an IED* Oh this guy DID put the safety pressure relief valve on his tank LOL
@bethlangkamp65664 жыл бұрын
Nice job best I’ve seen so far.
@alaaeldin993 жыл бұрын
Nice creation! Can you please help me with the size of the fittings used?
@davidalbeirocardonapelaez84533 жыл бұрын
Excelente trabajo Solo una crítica Debió remover la pintura con la misma arenadora
@AlexisMartinez-nl5py2 жыл бұрын
You could sandblast your own sandblaster instead of sanding
@mikegalvin46554 жыл бұрын
Hi nice work but instead of grind your tanks sand blast then air blow paint after
@markrainford12194 жыл бұрын
Many people scratching their heads at you hand sanding a sand blaster.
@Greasymonkey69 Жыл бұрын
You should put descriptions i.e. sizes and stuff
@AutodidactEngineer10 ай бұрын
Why is your welder so smooth!! Is it an AC welder?
@MaverickProjectsOfficial10 ай бұрын
Yes right! In this video I used AC welder!!
@AutodidactEngineer10 ай бұрын
@@MaverickProjectsOfficial Would you tell me which brand? A part number would be so helpful!
@mattbrain20013 жыл бұрын
Looks solid. Fantastic welds with the stick!
@iu22973 жыл бұрын
How much did it cost all in??
@neonbeach624 жыл бұрын
Nice work, but not a money saving venture.
@jzeerod3 жыл бұрын
forgets to fill it with water...ends up on best gore...
@stefanodidonato38924 жыл бұрын
Nice work bit It Is not clear how does It work. Nice Better a schematic
@hassanmalik59754 жыл бұрын
That’s really nice job mate thanks to share this
@ALI-fj1xf3 жыл бұрын
Why do you insert water at the beginning ?
@nikolcheniko7124 жыл бұрын
How much presure need to work good, and how much capacity is your compresor tank
@MaverickProjectsOfficial4 жыл бұрын
Its works nice 6-8 bar . My compressor is 200lt.
@blacksea694 жыл бұрын
Hi What kind of compressor i could use to make a good sandblasting at least? My father has a 100 l but its only 16m3 /hour that is to say a 266 L / min Do you think it would be ok ?? Thanks again
@_y_a_h_i_k_o_54764 жыл бұрын
@@MaverickProjectsOfficial 200lt. Its huge and good good to use i think. I have a plan to buy 50lt. With 8bar its that ok?
@momomimi68932 жыл бұрын
Thanks alot.good job
@MaverickProjectsOfficial2 жыл бұрын
Thank you !
@jhonalvarado75994 жыл бұрын
Heii mii pregunta es. Como se. Lo. Vuelve a cargar
@buder51164 жыл бұрын
use the sandblast tank to sandblast the sandblast tank
@timok.58243 жыл бұрын
Good job, great stick welding. What kind of electrodes did you use?
@jesusreyes74763 жыл бұрын
E-7018 works fine for this kind of projects
@someone-gb2ec4 жыл бұрын
BOOOOOOM 💣
@noanoa42833 жыл бұрын
Nema plina unutra halooo
@Zophus14 жыл бұрын
Time! Lapse! Just sayin...
@ELPUMA084 жыл бұрын
Would you sell me one ill will buy
@jd53844 жыл бұрын
Where is the compressor
@lawrenceogden86823 жыл бұрын
great video
@МестныйУмелец3 жыл бұрын
Good job 👍👏
@jackedwards13064 жыл бұрын
What hose did you use ?
@ruben49364 жыл бұрын
ibix sandblaster is best product and 0.2 to 7 bar air pres
@АлександрСтепанов-т8л4 жыл бұрын
Привет
@ruben49364 жыл бұрын
@@АлександрСтепанов-т8л Привет
@mmproject30103 жыл бұрын
👍👍👍
@DLANKTECHNIC4 жыл бұрын
good job
@raptors31644 жыл бұрын
Excellent piece, thanks for sharing.
@POWERnick.4 жыл бұрын
Ωραια κατασκευη και πολυ καλο βιντεο!
@Marcinlog4 жыл бұрын
Good Job :)
@MunnaKhan-to5bd4 жыл бұрын
Price in india
@s.k.s.k.10654 жыл бұрын
8003273574 price 12000
@josol79224 жыл бұрын
Excellent 👌
@RadioWerwolf3 жыл бұрын
Good job. I hope those fittings you welded are not galvanized.
4 жыл бұрын
Great work! Did you use that fuse casing as a nozzle?
@MaverickProjectsOfficial4 жыл бұрын
Thank you !!! Yes and its works fine. You will see it in my next projects if I use the sandblaster.
4 жыл бұрын
@@MaverickProjectsOfficial Yep. I keep watching. That nozzle is a great tip! Thanks
@fladoodel4 жыл бұрын
You should really use some kind of lubricant when you drill holes through steel. Will keep the drill bit sharp a lot longer and will prevent it from snagging on the metal and breaking the bit or hurting your hand etc