1000W 8 mosfet EGS002

[@PhdHung]

Sine 1000VA inverter uses 8 mosfet. Use the EGS002 board. It has low battery protection, over temperature protection, overload protection. Facebook group : bit.ly/CreativeElectronic Download file here : File in bit.ly/AllLink

[@BiteYt69]

Can't open the files

[@aleksandr4410]

the download link goes to the facebook group, but not to the file

[@omerfaruksahin5009]

Do you have a Gerber file? Does it support 24v dc input? What protection features are available?

[@scienceandtech7164]

Thanks for work Please can you design a high current DC to DC converter with variable output . current 20a and output variable from say 15v to 80v. Input is 12v and 24v. Thanks

[@jayjaycabana8348]

what file # sir ?

[@younchaounjankouo9736]

With the assembly diagram the explanation is perfect

[@sergioluiz6516]

I mounted the inverter and it really works great. Assembled it following the drawing where the components appear mounted on the board because the schematic was illegible. In the drawing, the correct value of the resistors on the left of the LM358 trimpot adjustment is from left to right 4.7R, 1K and 1K. The value of the resistors on the back (right) of the LM 358 are 2K2, 2K2 and 10K. The resistor connected to the base of the S8050 FAN is 2K2. Above the 2.5uF 630v capacitor the square piece is a mini bridge rectifier such as the DBL107G and the terminal - it is marked wrong. It must be connected to the 100K resistor side under the + terminal. Below the mosfets from left to right the 2 holes that appear without connection between the 4.7R and the 10K resistor must be connected with a piece of wire. Also, to reduce the no-load power consumption from 2 amperes to 1 ampere, I wrapped the wires that come out of the board to the 7v primary of the transformer in 1 ferrite ring (I gave it 5 turns). I used 2 separate ferrites. 1 for each wire. The transformer I bought here: www.center-ti.com.br/transformadores/transformador-para-inversor-1000w-saida-220v-entrada-7v It is also necessary to reinforce the tracks of the mosfets with a thick rigid wire, as described in the video, because the current circulating in these tracks can be very high depending on the load.

[@xakepvolt8626]

Кинь схему пожалуйста

[@user-us6jh5vs9z]

please email me the schematic and PCB

[@davidkinuthia1052]

Hallo sir I couldn't find the yr1030 meter in my country but I had a digital meter that was faulty I took the shunt and guess what it worked and the inverter is working fine thanks man God bless you

[@shadmehraria5473]

I made this project, Everything is ok except the current consuming with no load.It's about 2.5A .Trafo is high power 220 to 7v 30A.

[@ominowamichael3707]

Wow, exactly what I've been looking for, God will bless you with more knowledge

[@PhdHung]

[@maulanaahmad7751]

thank you, for your help I will try the raft

[@buiquangdai955]

Mình thấy rất hay , tuy nhiên bạn nên đổi cho mosfet quay lưng ra ngoài để tiện lắp tản nhiêt.

[@PhdHung]

đây nè kzbin.info/www/bejne/oJLXppqPitJ_hs0

[@osaretininnocentifaluyi7485]

Excellent job, God will give more wisdom and strength

[@abna5742]

Thanks you are the best engineer I have seen plz make a 2000w inverter with egs002 like this one because I wanna make it )thanks

[@nonatocosta543]

This is one of the best channel on youtube

[@johnmirajkar]

Perfect Ditail Education video 👍 keep it up sir 🇮🇳

[@udisami9856]

1. Those mosfets should be facing inward. 2. The gate drive resistors should be at least 10R each. 3. The gate off resistors should be at least 20k each. 4. Fast decoupling input caps are missing. 5. Power traces are too long, no caps in the way. 6. Shunt resistor will desolder itself at 500w load. 7. Egs002 is not modified (probably will get fried pretty early). What happened???

[@pawelwojtasik]

Witaj Jak zmodyfikować EGS .

[@electrotechnik2863]

Woow. Very cool project. Thank you for a great interesting video 👍👍👍

[@hugocamaras]

Ótimo inversor! Muito fácil de fazer pois é placa de face única! Deus te abençoe!

[@PhdHung]

[@user-us6jh5vs9z]

please email me the schematic and PCB

[@BENJY0919]

Excellent, I have always been interested and I like to see your investor designs. You are brilliant I'm waiting on 12v @ 60 and 16 mosfet

[@user-cp4xt3qc6q]

Сюда надо добавить два дополнения: 1. Автоматическая зарядка аккумулятора с защитами. 2. Автоматическое включение данной схемы при отключении сетевого напряжения в квартире.

[@subratabarman7009]

nice project sir ...thank you for shareing this ...

[@PhdHung]

[@jabemil]

Amigo excelente proyecto pero no me deja descargar el diagrama para realizarlo en casa no deja descargar el archivo

[@ayhamalbaali378]

Thank you bro I want to ask you if this inverter has a stable output when l have 500w load

[@nanopower4065]

Thanks a lot sharing with your idea,work,research

[@baasityusuf4778]

God bless you

[@PhdHung]

Thanks bro

[@baasityusuf4778]

You are welcome Bro, I've been watching most of your videos since yesterday and I'm very excited. God bless you once again 👍👍👍👍👍👍👍

[@PhdHung]

@@baasityusuf4778 I am very happy to hear that. I share it all for free, Hope you will share my channel with everyone.

[@baasityusuf4778]

Surely do. Thank you very much.

[@baasityusuf4778]

Hello Bro, I tried this inverter but 4 mosfet to the right are getting hot without any load, please help as I'm training my son on how to do this

[@khaked-all-sade]

best wishes

[@PhdHung]

[@piyalweerawarne6335]

You are doing great job thanks for knowledge sharing 👍😊

[@PhdHung]

Thanks

[@bomche115]

Tuyệt vời quá. thanks bro

[@PhdHung]

[@nangluongxanhhongson648]

Biến áp sắt hiệu suất thấp lắm, anh đã thử mua dây 3 ly về quấn 7v vào cái ổn áp Lioa 1,5kw và dư 8 motfet 80n80 chạy 48v để khi cúp điện chạy qua MPPT kết hợp với ac quy, tuy board ES002 nó tự động mở rộng xung thì khi không tải nó chỉ ăn tầm 0.4 ampe nhưng đo thực tế càng chạy công suất lớn hiệu suất càng thấp, 100w bình được 80w Ac, 1000w dc thì chỉ thu được 750w Ac, anh cũng ráp kích 24v 8 motfet với b2 biến áp áp xung E4220 quấn đồng lá 4 xem và lấy luôn 4 con cầu H của hòa lưới Suoer 1000 qua nhưng hiệu suất cũng chỉ đạt 80%, 1000w dc thu về 800w Ac, cuối cùng dùng luôn cái kích Suoer 2000 nó đạt 90% vì nõi biến áp nó tốt hơn loại mình mua ở Nhật Tảo, dù mình quấn cục tốt tẩm vec ly vẫn không ăn thua... Cục biến áp Lioa thử kích từ Ac cao cấp vào nó đạt 95% nhưng của mình là DC được ES0002 nó băm ra mà thua con pic của thằng Suoer nó băm mịn hơn nên ít hao hơn?

[@huangiap8874]

Bạn có bán cục biến áp này ko, hoặc cho mình xin link mua hàng với. Ko tìm mua đc loại biến áp 7-220v này

[@idjd777]

3:48 mẹ ơi kênh này của người Việt Nam 😀😀😀😀😀

[@PhdHung]

:))) ai cũng biết mà

[@idjd777]

@@PhdHung giờ mới biết nè 🤣😂

[@mizosaydah7314]

Good job 👍 I'm waiting from you voltage stabilizer using microcontroller

[@quangdung1354]

Mạch hay nhưng Ngại quấn biến áp quá

[@PhdHung]

|Kiếm biến áp UPS ấy bạn

[@hichamtassi1753]

Hi, what number is the link to this diagram ?

[@paulpixzy5297]

Thanks allot ..am with you

[@PhdHung]

[@SandipDas-ct3dl]

#homemade 102# #request video# Make a line interactive 1000va UPS that can run 500watt computer using 7 to 220v transformer... So that...when main power fails...it will automatically enter backup mode...without restarting the computer...without any data loss...

[@PhdHung]

ok. Sure.

[@manishicst]

Truly amazing brother 👌👌👌

[@abdellazizezzerkali370]

معلم ومنك نتعلم

[@loungelizard836]

Are these stackable? I mean, can you sync multiple 1000W inverters so they are in phase in order to have higher output: 2000W, 3000W, etc.?

[@domotronicasyonarhe]

Amigo me gusta tu proyecto pero no veo el diagrama que dices solo lo envía a uno a facebook y ya me puedes regalar el diagrama así como lo hiciste se ve 💯

[@CC-cx3er]

Hay quá anh ơi ❤️❤️❤️

[@PhdHung]

thnks b

[@sssaskke]

me agrado el titulo pero cuando veo que no son Watts y son Volts-Ampere ya no, me podrias dar el factor de potencia o los watts de potencia que tienes al final?

[@costa1250]

Parabens pelo video gostei mais um escrito.

[@Dc_tech386]

Great work love your work always .a quick question can I need to know about the frequency and duty cycle resistor location on the broad is the 2 pwm Ic the ones I need to fine the resistor for the frequency and duty cycle I need to use it on my vfd single phase drive circuit

[@KinhKha-lm2zl]

he he he cái mạch này gắn vô cái biến áp 1500va-900w '/24 v của anh được không em ....he he he

[@PhdHung]

cần chỉnh lại chút anh à

[@KinhKha-lm2zl]

@@PhdHung he he he cám ơn trước ,hôm nào lấy đồng hồ đo V điện vào rồi báo em là mấy vôn nha

[@PhdHung]

ok anh

[@jean-philippedognon8814]

Great job, can you please share the file ?

[@abubaker_rizgalah]

I see that you put 10kohm different from EGS002 scheme your design work well and I see heat sink over resecetors And what happened if 4.7 ohm damaged and mosfet is on I know there EGS002 protect but I want to protect the mosfets also from damage

[@PhdHung]

Very simple. using a fuse

[@kruthiktr1156]

Can we use toroidal transformer in this?

[@Davidslabofficial]

Yes you can but keep the specification as shown in this video 7v to 220v 1000watts

[@klsonidhanla]

Very nice dear brother 👍👍 This is my favorite board. Can I use 400v dc to 220ac?? Change the MOSFET and capacitor and 12v 5v supply for driver board.

[@juliusparker3039]

Very good, expecting the Downloadable circuits diagram

[@Electronica_RMS]

Great job. I'm your fan

[@PhdHung]

Thanks bro

[@f.santosfrancisco5667]

Fantástico, bom trabalho.

[@vaidyanathbirudukota4777]

Good work....

[@user-us7wy9hv2r]

جزاك الله خيرا ....

[@PhdHung]

[@aboimad5178]

My frind today all ppl like to use the smbs ... Flyback transformers ... Pls make some videos for this Thanx

[@lovepreetsinghgill517]

Very good video, I liked it very much

[@PhdHung]

😍😍 thanks bro

[@mcpur01]

Mantaf sangat berguna

[@Jerimahsts]

What kind of transfer paper was being used? I also make PCB'S and use the toner transfer method but I have never seen paper like that. Crisp clean flawless transfer please let me know. Awesome video, very nice!!!!

[@africantech5]

Thanks for the good job pls can't I used 47R for the Gate resistor

[@pabloibaceta5932]

What kind of paper You use for print with a láser printer for make pcb?

[@atulhostvideos]

Can I use it to convert directly 200~240 Volts DC to 200~240 Volts AC without that transformer?

[@user-ds7vn1mr5b]

Great job ... I'm one of your most fan ...

[@nbsgamingyt6920]

Sine inventor or normal inventor explained video upload please

[@liaskliask]

Great job!!!thanks!! you are NO 1!!!

[@jahirulislamshovon9256]

Awesome!! Please tell me how to use only one switch instead of two . I need automation

[@eliasc6877]

Que papel usaste para la imprecion tóner...

[@RahardianPahlevi]

MANTAP 👍👍👍

[@Pilotfly2023]

Tks, friend!

[@mrevilehieu]

Chào ytb việt nam

[@pedrohodge7001]

nice work bro, how can I modify it to work with 24v in ?

[@Vanduyeamigos]

Amigo parabéns pelo canal. Vc teria um esquema de inversor de 2000 watts com trafo de ferrite?

[@gocchiase8785]

A hướng làm mạch cân bằng pin lithium dk k

[@PhdHung]

kzbin.info/www/bejne/b6bSe2uhbJylrdU

[@bishal.dangol]

Bro please make inverter that have 50-60hz 220-250v and 1000w.

[@roshanindika903]

low battery protection not work properly....at the moment battery running 10.5V,inverter not off....what's the matter any error of Low battery protection Circuit side????????????????????????

[@PhdHung]

You need to calibrate it

[@roshanindika903]

yes.I calibrate it to 10.5V to off using trimpot rotating..but at the 10.5V not off..

[@sawi2305]

that input to the travo 7 volts, to be 12 volts what needs to be changed. Tanks before🙏

[@saliouthiaw554]

thanks you for giving us these awesome content. Do you have a website where we can read details about your project ?

[@tranlang]

Quay lưng fet vào trong thấy hơi sai sai ad à. Lắp tản nhiệt bị đè lên trở rồi ad !

[@yasimmehmood2317]

Great job excellent project please sir send me new link in media fire video Link does not work

[@rahulkoley6161]

#Homemade 102#..in ur circuit...u can used 10 mohm shunt resistor... Then...if trafo output get .............short circuit......this shunt can protect mosfet or whole circuit....from burnt....or not...?? ......and......can I use this circuit...with soft start disabled of Egs002 by jumper settings (jp2 & jp6)...or...not...........??

[@raphaelvicent2436]

Top. Esse vou tentar fazer . Alguém do Brasil tentou?

[@maulanaahmad7751]

What you feedback 220v use optocopler?

[@hemanthkumarr6856]

Please make a inverter with battery charging and auto cut off like commercial inverter

[@leandrodeaguiar898]

Ja deixei o like exelente

[@peshkawtmahmood509]

Thanks for sharing this information, does it include the charging battery part?

[@johnbillalcalde9748]

Wow good circuit.

[@manishicst]

Sir i thnk we will face difficulty in placing heatsink bcz resistor are present backside

[@arissutaat4947]

Thank you friend. whether this circuit can use 24v transformer and 24v battery input

[@davidsobral1737]

hi all right i would like to know which conponet is the one that this asima of the capacitor 2.5uf 630v he does not have in the list only has the design of the conponemte and the +/- sign?

[@PhdHung]

DB107 - diode

[@victorcremella9156]

hola muy buenos tus proyectos felicitaciones!!! una consulta esta bien el ajuste de 300ns en el modulo de egs002? gracias .

[@asc556]

Thank you sir for sharing. I have one question: i see that you use 4.7R (7.5R in the schematic) resistor between the driver and the mosfet gate. And i can't help but wonder if isn't too low value. I was expecting 10R for driving 2 mosfet with the IR2110. My question is: isn't too much current going thought the IR2110? Cheers.

[@PhdHung]

Well, the mosfet I use has a very low parasitic capacitor. Furthermore, the SPWM frequency of EG8010 is only ~ 20Khz. It should work fine. but 10R or 15R can be used.

[@tranviethieu193]

you can do inveter 48v to 220v 10kw

[@baniadamtv]

Nice.. 👍

[@josephochoa4317]

Why does one use a 12V to 220V or 120V transformer? Or Why I don't use an ups transformer?

[@charooncharoendee7180]

Thank you very much please I want to know that the capacitor and zener diode values ​​on the lm358 IC yes how much yes

[@SandipDas-ct3dl]

#admin# can you plz tell me...why are u using shunt of 10 milliohm..? What is the function of this shunt here...?? And...how to set for overload...? Or it doesn't has overload protection..??

[@scienceandtech7164]

Thanks for work Please can you design a high current DC to DC converter with variable output . current 20a and output variable from say 15v to 80v. Input is 12v and 24v. Thanks

[@user-ew3lk7cp9g]

Please give me a circuit pattern, in the link can't load.

[@user-em2mo9or2r]

hi I'm New Subcriber,.I want to ask, how many ampere and diameter for the Shunt resistor,..

[@PhdHung]

0.01R 50A.

[@hoangtung-ye9gn]

Anh là người việt nam ạ có thể cho e xin sơ đồ trên giấy không ạ e thắc mắc 2 con tụ với con transitor gần ic 7805 là bao nhiêu ạ

[@royrafa3933]

thank you i made it...

[@willylinares9430]

excellent video what was your source of power? a battery 12? how many amps? thanks for the reply.

[@osirishz1797]

so that the output gives me 110v in the secondary, what voltage must be in the primary and what amperage must the transformer be?

[@MasReza]

Sir what do you think if i add inductor for this?

[@PhdHung]

of course better

[@francerantoniodelarosarami4577]

hello, may somebody tell me, if i decude to use a 120v transformer, do i have to change something or it can work the same way?