TP4056 module modification for more lithium Batterys

[@homemade_101]

DIY Power Inverter 12v to 220v : kzbin.info/www/bejne/gV7KhH2Ens2Yj6s

[@NikiBretschneider]

That 0.5A is current drawn from the 3P battery due to equalizing its voltage to a 1P one. This is why the current goes down, the 3P battery become slightly discharged as it slightly charges the 1P one. Furthermore, that transistor end up in saturation (due to heavy base current) connecting the B- (collector side) to the ground (emitter side), which does virtually nothing to the charging current, because charging current still goes through TP4056, because this IC regulates the current at the positive side. Changing that programming resistor to 1kΩ increases the output current to the 1.2A, which is kind of unfortunate as the TP4056 is rated to 1A max. This modification is nothing than a nonsense from its beginning to the bitter end.

[@homemade_101]

thank you

[@MrFlagstaf]

@@NikiBretschneider nice! that was my thought from the very beginning. You confirmed it, thanks! Absolute nonsense

[@kailasingle460]

One cell of 4.2 v How much max current we can give?

[@DARKNESS19906]

@@NikiBretschneider yeh!! Your right 👍👍👍👍

[@emanikebiz]

@@NikiBretschneider HI. donde te puedo escribir?

[@Angkasa_Berkah]

very useful knowledge, thank you great video

[@homemade_101]

enjoy beo

[@عليالسلطاني-ع8ب]

من العراق احييك ايها الانسان البطل فعلن لديك ابداعات قيمة شكرا جزيلا لحضرتك 🌹

[@homemade_101]

thank you and welcome

[@МЫПИОНЕРЫСОВЕТСКОЙСТРАНЫ]

@@عليالسلطاني-ع8ب Что за каракули ?

[@emilsangatta937]

Hi, is it posible to mod drone remote control so it can yaw smoother?

[@homemade_101]

yes,.. you can try it

[@RixtronixLAB]

Creative video, thanks :)

[@homemade_101]

thnks

[@Jim_One-wl4ke]

Wow! That’s cool. If this could be done , may I know is it possible to do one mode similar to make a 3S bldc esc into 200v bldc esc ? I didn’t see anyone doing this yet. Thanks ❤

[@homemade_101]

welcome. try

[@noanyobiseniss7462]

nice but how to charge them when they are in a 4s configuration?

[@homemade_101]

This connection is not correct. If so, we should do a separate battery charging by banning with a 4s balancer circuit. I made this as a test for this module.

[@noanyobiseniss7462]

@@homemade_101 I was considering using a NC relay for the 4s and pull it when the charging circuit activates but then i'm not sure if the relay will fail open or closed and that would be a fire hazard. also considering i wish to use it in a battery back for my old hammer drills there would not be room for the 3 high power relays that would be needed. I could use a A triple-pole switch but i don't like manual control especially if you forget then you fry the system.

[@PritamDe-w4m]

Very good First time i saw a real video on this topic on youtube.

[@homemade_101]

thank you bro

[@iosifferencz5432]

Multumim,bine venita inovați,merita abonat ❤

[@homemade_101]

Bucurați-vă și bun venit canalul meu.

[@nfactor1]

О мой индийский друг! Я сначала не узнал тебя в перчатках. Когда пойдешь в майкрософт работать?

[@sencerylmaz3375]

Not work. TP4056 out 4,20V - 0,65V Base = 3,55V out insufficient charger

[@homemade_101]

what

[@sencerylmaz3375]

@@homemade_101 you are a fraud

[@curits8260]

what the purpose of this? to increase the fast charging?

[@homemade_101]

Stop burned the module

[@curits8260]

@@homemade_101 thank you for the reply. this is good idea to stop burning module.

[@sujanmajumdar9760]

Now this board 2amp?

[@homemade_101]

yes

[@ΔιονυσηςΓιακουμελος-ξ3ι]

Μπράβο πολύ έξυπνο. Συγχαρητήρια.

[@homemade_101]

thnaks

[@Aaliyah21]

💯💥Good job

[@homemade_101]

thank you

[@hanymagdy2095]

Dear you are creative. The first question, what is the benefit of the 1 kilo resistance? Why didn't the blue LED light up after the complete charging? Thank you.

[@homemade_101]

A carbon film is used because the SMD resistor burns when a large current is passed. It will not turn blue because the batteries are not charging at the same time. A balancer will be used for this.

[@hanymagdy2095]

means that after the charging is complete, it turns blue and thank you

[@homemade_101]

@@hanymagdy2095 welcome

[@Freeman666Gordon]

These TP4056 boards cost 1.5$ for 10 of them, but 🤡 "forgot" to measure voltage on cells after current fell to 10% of nominal.

[@homemade_101]

yep

[@4EPEhAIIIKA]

..улыбнуло это. впаянный транзистор ничего не делает. Для усиления по току нужно регулировать резистором, а если хотите ещё больше ток, тогда транзистор правильно ставьте в схеме с общей базой. Тоесть эммитер на выход + линии а на коллектор выход + с платы. Тогда будет транзистор работать в схеме с общим эммитером и коэфициент усиления по току можно выставить в соответствии с его hFe по даташиту на транзистор. И тогда можно не впаивать резистор на место родного smd R3. Ваша попытка была нацелена именно на то, чтобы сделать масло маслянным, причём неправильно с точки зрения включения транзистора. Получилась вообще абракадабра. Steve Miller Band ваc вдохновлял)))..

[@homemade_101]

nice. thank your advice

[@starikvangelis]

Люди вы понимаете что это не будет работать должным образом! Как так можно обманывать 🤦🤦🤦

[@seharrubab9441]

Will it work

[@florichest8404]

Blue wire was disconnected from the transistor. How come it is charging when the path in the circuit is incomplete???

[@sergeypetrov1358]

😂 Какой смысл ставить транзистор пипец😅

[@homemade_101]

[@МЫПИОНЕРЫСОВЕТСКОЙСТРАНЫ]

Вроде как усилитель тока ?

[@س.ا.و.ا.ک-ج3ح]

ایده بدرد نخوری بود نیم امپر 😂😂😂

[@homemade_101]

[@edsonbomber5]

Nessa configuração esse transistor não está servindo para nada 😂😂😂😂😂😂😂😂😂

[@homemade_101]

ok

[@davey2k12]

Whats the point in the big phat transistor doing nothing 😂

[@Jackson-dx6du]

Зробив зарядку на 0,5 ампера🤷

[@homemade_101]

yes i thik battry was charging

[@EvHindustan]

😂😂😂 5amp not 500 mah only😅

[@homemade_101]

Ignorance is visible.

[@kelekkelek8102]

Apakah pengecasan ini bisa di lakukan pada sistem seri

[@Aaliyah21]

Super❤

[@homemade_101]

thanks

[@kailasingle460]

Sorry brother it is taking current more than the cell's limit. In this way you are killing that battery. Can you limit the current below 500ma

[@homemade_101]

thank you

[@johnbodlina3193]

Co to je? To máte v Indii nějaké nové hodnoty pro Ampery. Toto je velký fail.

[@homemade_101]

okey

[@youbiku]

i'll tray it in my project to

[@homemade_101]

good luck.

[@dapakers]

the ic max current output is 1 amp only.theres no way this could boost current output.. cant full everyone though

[@homemade_101]

full everyone

[@wv1vsu]

Thanks 🙏

[@homemade_101]

welcome

[@ПашаФедькович-к7д]

И нахера там транзистор если все всеравно идёт через микруху, она и ограничивает ток, максимум может дать 1А заряда. Читай даташит и схематику изучай тормоз!

[@homemade_101]

sorry

[@MrGekson]

Последовательно с микросхемой еще транзистор. Ну да смысла от него нет. Это наверно если шунт в его цепи ставить, который микросхема будет анализировать.

[@GUILHERME-CRUD-4K]

Carga lenta

[@homemade_101]

yes sorry

[@СергейСергей-м2в1ы]

Чушь полная. Только время потратил

[@homemade_101]

thanks

[@Slavianin-]

everything he did makes no sense. You could just hook up the rest of the batteries

[@homemade_101]

yes you are

[@2042moeen]

Missgide

[@Slavianin-]

??????????????????

[@homemade_101]

why

[@Tx_6969]

Get some real knowledge 😂😂😂😂😂

[@homemade_101]

😄