Honda EU2000i, EU2200i, EU1000i, & EU3000i Carburetor Replacement

Рет қаралды 3,680

Күн бұрын

Пікірлер: 43

@keithw8646 Ай бұрын

Great video showing the steps. I just got an OEM Honda carburetor and was going to swap it this morning. Now, I’ll grab one of those hose clamps before I start. Thanks for sharing.

@ThatGeneratorGuy Ай бұрын

Thanks for watching!

@ClintSchuver 2 ай бұрын

Hey sorry after looking at other comments and responses i ordered thank you for the videos and product

@ThatGeneratorGuy 2 ай бұрын

@@ClintSchuver thanks for the support!

@colloidalsilver1096 2 ай бұрын

Please recommend an after market carburetor for a eu1000i that you most use.

@ThatGeneratorGuy 2 ай бұрын

@@colloidalsilver1096 thanks for watching! I’ve used this one because it’s a Huayi carburetor: a.co/d/7fRZeg2 and had great results. I’m probably going to start selling carburetors soon with the proper connector as well.

@darrellwagster1619 2 ай бұрын

Do you have the wire diagram trying to understand what the wires do

@ThatGeneratorGuy 2 ай бұрын

@@darrellwagster1619 I have never seen a wire diagram for the Honda step motor. I don’t know if there is one.

@ClintSchuver 2 ай бұрын

Can I purchase a plug that u make ?

@jaaww7549 4 ай бұрын

Where did you buy the jst connector for the Honda cable. If I had one, I could fix mine. Great video, btw!

@ThatGeneratorGuy 4 ай бұрын

Thanks! I think I got them from Digi Key

@WendyandGeoffPattison Ай бұрын

Why do you work on the generator on the floor? Surely it would be easier and more convenient to do it on a bench? And less liable to lose small parts.

@ThatGeneratorGuy Ай бұрын

@@WendyandGeoffPattison, I have limited space because I work out of my garage. A bench would definitely be awesome but that’s probably 4 generators worth of space.

@shericollins0214 4 ай бұрын

Are you willing to sell the adapter. I would like to purchase one.

@ThatGeneratorGuy 4 ай бұрын

Yes, You can purchase it here: www.ebay.com/itm/135227537968

@onthethrottle7104 3 күн бұрын

Why not take that stock carb and take it apart and clean everything instead of replacing it? I'm only asking because it seems like the stock carb would be better than some china knock off, but I'm not in the know if there is a good reason and I can tell you know your stuff real wall so wanted to ask. Thanks in advance!

@ThatGeneratorGuy 3 күн бұрын

@@onthethrottle7104 I’d say 99% of the time you can clean them just fine. Many people have trouble cleaning carburetors properly and a generic from Amazon works great except for incompatible stepper motor connectors. I made the adaptor to be a solution for people who want to do the job themselves cheaply, quickly and correctly.

@onthethrottle7104 Күн бұрын

@@ThatGeneratorGuy Thanks and I did see the adapter, very nice adapter system you came up with! As for cleaning the carbs, you make a lot of sense with what you're saying about most not able to clean them correctly. Thanks and great channel.

@ThatGeneratorGuy 17 сағат бұрын

@@onthethrottle7104 thanks for watching! 👍🏻

@maximussam2466 3 ай бұрын

My carburetor is stuck to the engine, and my front gasket is caked on. What would you recommend to pull it off? It won’t event budge. Thanks!

@ThatGeneratorGuy 3 ай бұрын

@@maximussam2466 , just pull harder. It will come off. It’s probably just stuck on there with old gas

@ThatGeneratorGuy 3 ай бұрын

Also, I’d tap/smack the bottom of the carb with the handle of a screwdriver to help break it free

@11bravo18 Ай бұрын

@@ThatGeneratorGuy The carb on my 2200i wont budge, and thats after tapping and prying from behind. H E L P

@ThatGeneratorGuy Ай бұрын

@ , If you’ve unbolted the carb and removed the air filter box the only thing holding it is old gas that’s gummed up and is acting like a glue. Speak some brake cleaner (not carb cleaner) around the back side of the carb and keep smacking it, it will come off.

@dieseldawg7132 6 ай бұрын

Hey bud I have a questions, I have one of these generators… recently took apart the carb and cleaned it up really well to include the jet and the brass orifice…. Used some carb cleaner so it was super clean then I ran fresh diesel into the tank with some seafoam…. To make sure it cleans anything that I might have missed…. My issue is that when I get to around 1600 it stumbles on its face then slowly tries to ramp Back up….never got it high or it to show overload any clue why it might be doing that ?

@ThatGeneratorGuy 6 ай бұрын

1600 watts? If your initial issue was old gas/gummed up carburetor, you probably didn’t clean the carburetor good enough. Those are really good engines and they will tolerate a lot so it’s not surprising that it’s able to run. I’ll be doing a video on carburetor cleaning soon but if you cleaned all that’s visible (including the plastic pilot jet) then just do the following 1.remove carburetor 2. Remove bowl 3. Blow compressed air into the small brass hole on the choke side of carburetor (there are two holes, you want the one on the side with the pilot jet) 4. Alternate spraying brake cleaner (no carb cleaner) and compressed air a few times and it should be good to go

@dieseldawg7132 6 ай бұрын

@@ThatGeneratorGuy cleaned it out again and replaced the old filters, ran some ethonol free gas from buccee’s and some seafoam It finally ran to higher wattage and thanks!

@dieseldawg7132 6 ай бұрын

@@ThatGeneratorGuy quick question why the brake cleaner over the carb cleaner ???? Is there no coating on the fuel system we should worry about ???

@ThatGeneratorGuy 6 ай бұрын

@@dieseldawg7132, these carburetors have rubber parts and the carburetor cleaner will destroy them and make them gummy (float needle tip, bowl o-ring, and o-rings on the pilot jet). I use brake cleaner (the non-chlorinated) the whole way and never have to worry about ruining components. 👍🏻

@ThatGeneratorGuy 3 ай бұрын

If you're interested in purchasing the adapter, you can do so on ebay here: www.ebay.com/itm/135227537968

@sreihart 3 ай бұрын

Wow. $43.30 for the adapter? That sure seems to be kind of high. I appreciate the video, but...

@ThatGeneratorGuy 3 ай бұрын

@@sreihart, Yes. It’s cheaper!👍🏻 A new OEM carb is $100+, plus tax. A generic carb will be $15-$25. If you’re the type of person who will need another carb in the future, great you already have the adapter and get another cheap generic, if not, it’s still cheaper than OEM to buy the connector too.

@bobshanahan2913 4 ай бұрын

Do you sell your conversion adapter?

@ThatGeneratorGuy 4 ай бұрын

Yes I do. You can get it here: www.ebay.com/itm/135227537968

@stormstrike1845 2 ай бұрын

$60 shipping?

@ThatGeneratorGuy 2 ай бұрын

Usually it’s like $8. They’re UPS rates, not mine. If it’s that expensive you either selected a fast speed or you live far.

@stormstrike1845 2 ай бұрын

@@ThatGeneratorGuy ok

@stormstrike1845 2 ай бұрын

@@ThatGeneratorGuy I see a lot of people just cleaning the carburetor. I left gas inside for like 2 months and it wont start now. I had a different generator do the same thing. Could a simple cleaning fix it? How do I know if I need a replacement

@ThatGeneratorGuy 2 ай бұрын

@@stormstrike1845 , You almost never need a replacement. Cleaning works 95% of the time for me. Most people though either don’t have the knowledge to properly clean it or just don’t care to spend their time cleaning and would rather toss a $30 generic in and have it up and running fast and easy. That’s why I made the adapter (for people who want to simplify their repair)