Honda H'ness CB350 - Handlebar Risers - Does it help?

#HondaHighnessCB350
Most morden bikes these days focus more on the design from a appearance perspective than the rider perspective.
The Honda Highness CB350 is not an exception and so the handle at times feel short making the riding posture uncomfortable.
This video explains how the handlebar risers can help improve riding posture and comfort.

[@sydchasinglife]

This cleared up a lot of doubts on handlebar raisers, never used them before, thanks Raj. I've seen you've installed fog lamps as well, hope you make a video on that too!

[@RajkaGarage]

Thanks bro.. in case you missed it, below link for fog lights Installation without tampering OE harness. kzbin.info/www/bejne/Y6TagJmfgpeXo9U

[@arv1ndgr]

Do check his previous yet very detailed Wiring Manuel video on that

[@tashibhutia8353]

Howdy! SaEd, Is it true that 5.3 height would be better to choose the inclined one and above height should go for the straight. What would be your recommendation.

[@ManishYadav-me6gy]

I’m feeling pulled one side pls suggest ?

[@shyamfootprints972]

Excellent Analysis. Useful stuff. I also purchased the straight handle bar risers for my CB 350 RS and after installing it, I went on a 1000 kms ride last week. The risers helped in reducing back pain for me, but the pain did not go entirely. So this week I have ordered the inclined 'reach' handle bar risers and I hope this one is even better than the straight ones. I will know only when I install the new ones shortly. Also I found that the handling improved tremendously on my CB 350RS. I did not expect that and I felt that the money (Rs. 1050) I paid to Carbon Racing for the risers, was well worth it and therefore I purchased the angled risers now.

[@pankajjalotra5338]

Bro i too have 350Rs and felt pain on my back Plz tell me upto how much it improves after installing handle bar raisers

[@sujannatraj6863]

How are the inclined handle bar risers?

[@praveenhegde8107]

How are the angled raisers and what's your height.

[@no22sill]

What's your height for reference?

[@X_Wolverine]

update? how much inclined one helped

[@ridermania2070]

Nice informative video again. And very thoughtful of recommending to cover the tank and not putting the caps back without putting some bonding adhesive.

[@RajkaGarage]

Thanks buddy

[@arv1ndgr]

Great video and detailed information.., Feeling sad for KZbin algo not increasing your subscribership, anyways Thinking of getting inclined raisers post lockdown

[@RajkaGarage]

Thanks buddy.. Do think about installing the inclined ones, one of the member from our Mumbai Highness group installed it, but later removed as the cables were at strain and also the handle switch position was titling downward. Regarding, my subscribers, recently read this somewhere" A millionaire driving a Bugatti- 1 million views. A millionaire showing you how to build a business to afford a Bugatti. - 600 views People don't want to be educated, they want to be entertained 😅

[@arv1ndgr]

@@RajkaGarage Yeah that was my fear, after seeing after hearing similar stories. It is possible to go for after market clutch cable if it's installed? Also, the 2nd philosophy is completely true. That might be the actual reason

[@devntube]

@@RajkaGarage - brilliantly said. No worries on subscribers, it will increase today or tomorrow. Be original and be honest as you are now... Best wishes.

[@RajkaGarage]

I think a Unicorn cable is longer than the Hness..will check practically and update..

[@arv1ndgr]

@@RajkaGarage no other KZbinr would go this extra mile! I'm sure nos would catch up, also as our CB350 will last for generations, future buyers would still be interested here Also, that unicorn cable check, that'd be so much help.. I'm 5'4" height CB350 rider hence feeling if handlebar could be located but near, it'll feel better for long rides

[@no22sill]

Nicely demonstrated

[@RajkaGarage]

Thanks buddy 😊

[@abhinandanghosh4056]

I found rust in a few places on my CB within less than a month of purchase; I always park my bike in shade or under cover from day one. Very very disappointed with Honda's paint job on this bike. The rust was all on the chassis, near the neck, under the tank, and seat bolt at the rear, got them the Topline service center to repaint the areas I could find, that too was a task, because their first attempt to repaint left out a few places, I got them to redo the re-painting and they replaced the seal bolt. The paint on the chassis, especially near the welding is not very good. I am assuming Honda just repainted the tank & body panels of their older stock H'ness and rebranded it as Anniversary edition, which is probably why the H'ness Anniversary edition has a higher chance of getting rust early on.

[@RajkaGarage]

Build quality of the new lots is really questionable. Have seen lot of such issues of late.

[@abhinandanghosh4056]

@@RajkaGarage thank you for the reply on both my comments on your both videos, came across your channel very recently, and subbed immediately. Really disheartened with Honda's quality, I chose Honda over RE solely because of RE's rampant rust issues, still having to face the same problem. Funny thing is my eight year old Yamaha Gladiator SS125 still has almost zero rust.

[@TheEverydayManChannel]

I had to reroute the clutch cable after installing the raisers. There was a lot of strain on the cable when turning the handlebar.

[@RajkaGarage]

Did you put the straight ones or inclined ones. Next i am going to try the RD handle to see if that makes it any further comfortable in long rides. May have to re route the cables then.

[@ashishsati1736]

​@@RajkaGarage still waiting ✋️

[@saijojoy6745]

really like your video so informative and goes to details ❤. am hearing good reviews and comfortness regarding aom handle bars. any thoughts on this .. 👍🏾

[@parthivnayak2419]

Yes I installed the same too raj

[@nileshgaikwad3218]

Hi Sir. I see this is 4 months old video. Maybe you are riding with it since then. Does it feel comfortable? I want to put it in my highness. Thank you.

[@aniketpassion]

More info on golden wrap on front suspension. Can you share a video or picture of how does it look

[@RajkaGarage]

Will do a video as suggested buddy 🙂

[@aniketpassion]

@@RajkaGarage great. I also have MH04 passing and was wondering if I can get it done from the same place you did.

[@nitinnaik833]

Why u need to change the original settings ? Sitting position changes by doing this . May be good for heighted person

[@RajkaGarage]

Yes, I installed the riser to make my seating position comfortable. With the stock position I have to reach out to the Handlebar and installing this has helped a great deal.

[@RikiHn]

Sir i am 6"1 should i buy incline or straight risers? The stock handlebar of the RS is not the best for me

[@amithskumar1040]

Same height bro iam also facing discomfort. Any solutin found?

[@RikiHn]

@@amithskumar1040 used hness handlebars. It solved my problem without the need for risers.

[@devntube]

Another informative video. But I'm bit confused. Motovin77 is using the same risers, he's facing issues of some of the cables getting streched when handles are completely turned to right or left.

[@RajkaGarage]

Thanks bro.. is Vinay using the straight ones or the Inclined one. Coz I was very particular about any strain on the cables, brake pipe and harness. And as you can see in the video, all the control cables and harness can easily accommodate the 1" riser. Especially the most critical is the clutch cable as any strain on the clutch cable will lead to clutch burn out and other subsequent issues and as you can see there is no strain on the clutch cable even after the hande is turned full left/right. I do have apprehensions about the inclined risers that they will put a lot of strain on the control cables and also due to the tilt back design of the riser, the handle switches will tilt downward.

[@devntube]

@@RajkaGarage - he's using the straight one... I'm leaving vinay's video link here - kzbin.info/www/bejne/kImcoHaOjquEm8U Check around 5min 30sec mark.

[@RajkaGarage]

If you notice, his handlebar is a bit more tilted towards the rider, and this probably is adding some strain on the cable when the handle is turned to extreme right. And, as long as there is no movement in the inner cable, it will not create any issue. Also just a practice (due to reliability issues of the clutch cables with the other 2 machine I use, RE and RX) I always change Clutch cables after every monsoon, regardless of the condition of the cable. Smooth clutch operations can save a lot of other things and adds to riding pleasure. Will be doing the same with H'ness too, though with a streched interval.

[@arv1ndgr]

@@RajkaGarage Noting your experience here🤝👍

[@devntube]

@@RajkaGarage thanks bro...

[@SachinKumar-cc1eu]

Which one is better inclined or straight one

[@RajkaGarage]

The straight ones are doing the job for me. The inclined ones will offer further enhanced posture but at the cost of some stress on the cables and harness.

[@_anandu.vishnu_]

Bro plz do a video on decolorization of the bend pipe....many users are facing this issue

[@RajkaGarage]

Sure mate..at the next available opportunity, will surely do.. atleast how to avoid it will surely help a lot of others

[@_anandu.vishnu_]

@@RajkaGarage waiting for that video mate ❤️

[@Yashvardhan1435]

Hello..honda service told that this will damage clutch plate ..please sharw your suggestion

[@arunjan9]

Nice video

[@sudheesh1989]

Hey! Are you still using the risers? How has your experience been over the past few months/year? Also are the cables still holding up fine without rerouting?

[@RajkaGarage]

Yes, I am still using them and they have made my overall seating posture better, if not the best. I am using the straight ones which doesn't need any cable rerouting and hence no issues in that area. If you go for the inclined risers, which are more comfortable, then you need to re route the clutch cable from outside the the fork pipe.

[@ManishYadav-me6gy]

Sir did checked out inclined ones as well ? If so pls do a video which is best

[@VlogsReviews]

Being 5'5 guy, you installed them. Now being 6' I'm worried about myself 😅😂. Please update how's the experience, any clutch or accelerator cable issues?. I'm gonna buy them once you update regarding usage and comfort.

[@hadouken2077]

Raj, Very helpful video. I was planning to install this on my CB350 RS. Thank you.

[@RajkaGarage]

Thanks buddy. The RS handle is further straighned up compared to the H'ness. so adding this can help the riding posture.

[@anildamodaran]

@@RajkaGarage Many thanks, Raj.

[@lakshaysharma7677]

Hi Raj, I've got the inclined units from CR and want to try them out. The hex nuts holding the handlebar clamp are extremely tight. How did you unscrew them?

[@RajkaGarage]

Use a good Allen Key and put some small metal pipe from the outer of the Allen Key to add torque if it's too tight. Just ensure to keep a cloth on the tank to protect the surface while doing this work.

[@lakshaysharma7677]

@@RajkaGarage thank you! Let's try this out. 😁

[@sudeshsharma8077]

How to fit indicator buzzer in Honda highness

[@lakshaysharma7677]

Hi Raj! Wow, any issue with the CB and you've got it covered. I have the same height as yours. On a longish ride my shoulders and neck were hurting because of the reach. These risers are out of stock on CR; alternatively, can we install different handlebars?

[@RajkaGarage]

I plan to install the RE Electra handlebar. Alternatively, instead of the straight ones, you can also check the inclined risers and reroute the clutch cable from outside the the fork pipe. Inclined risers are more comfortable than the straight ones. Regarding the Electra handlebar..will keep you updated on the same when I take that up.

[@lakshaysharma7677]

@@RajkaGarage thank you for the response Raj. I'll install the inclined risers when they're available and let you know how it feels. Warm regards.

[@ManishYadav-me6gy]

@@lakshaysharma7677did u installed sir ? Pls suggest even I’m planning to install

[@riku2384]

Nice n informative vdo bro..do make a vdo on rear tyre hugger also..

[@RajkaGarage]

Will surely try bro.. though I don't plan to fit on my bike, know few friends who have done it.

[@riku2384]

@@RajkaGarage 🙏

[@DileepreddySobhaKrishna]

Sir, how is your experience? Is the look enhanced or is the stock setting beautiful ? Based on your opinion I wanna a buy one if looks are not diminished.

[@RajkaGarage]

My height is 5.5 and so I had to reach out to the handlebar. During full turns in city traffic it used to uncomfortable at times. By installing this my posture has become more upright and I hands are much relaxed now. There is another inclined ones which can add more comfort. It does not impact looks by any means.

[@Faridudi]

Make the. Another video that we can see. That how you going’s to install the raiser.You have mentioned the details

[@RajkaGarage]

Will surely do that buddy.

[@jenishjungrana2587]

My Gear stucking while shifting down after emergency break? Any solution sir

[@RajkaGarage]

Hey mate, couple of factors: 1.how many kms have you completed on ODO? If it's less than 1500 kms and not even done 1st oil change. Its common for new gear boxes to be a little clunky especially from 3rd to 2nd as the gear dogs are not tuned with each other. If you see my very first video on the Hness when I took delivery and went to Pune from Mumbai, towards the end of that video, I was talking about the gears being little hard while shifting to 2nd and the time it will take a for the parts to settle with each other. 2. At times we get on the brakes suddenly and speed is killed abruptly. In such case it's very the Engine RPM is higher than the wheel speed and this tall variance in speed makes shifting hard. Also, just suggestion on oil change. Ask the SVC to use Honda Throttle Fully Synthetic 10W30 oil, if they are not doing it already. Coz some SVC are using 5W30 during free service. Both are recommended grades, but using 'Throttle' will make the gear shifting smooth. Hope this helps. Cheers and Happy Riding 🤘

[@Faridudi]

How you have installed the raiser

[@oyeguru2399]

Thanks for the video ... anyone, where can I get these in Mumbai / Thane ?

[@RajkaGarage]

Not sure if anyone is keeping them locally but you can definitely buy from carbon racing website.

[@shailendrabn]

Product brand name and price please.

[@RajkaGarage]

This is from Carbon Racing. Product details available in description of the video.

[@avisivamani007]

Bro I saw one KZbin video, problem is full left and full right if we turn the clutch wire becoming too tight are u facing same problem any?

[@rajeevpuri78]

W hich risers are best in hness inclined/ straight risrers .i am 5'9"

[@varun9373]

I test rode this bike but i felt pain in my shoulders while riding and it felt like I'm leaning towards the bar i had a rs 200 before and it hurted my shoulders while riding should i go for this bike or re? Re has an upright posture compared to this

[@smartfishingTony]

I ordered inclined raiser for better comfort, is it good?

[@RajkaGarage]

Yes they are definitely better than the straight ones, but just make sure you are re routing the clutch cable.

[@cyrilrodrigues2916]

From which vendor did you purchase the handle bar risers

[@RajkaGarage]

These were bought from Carbon Racing.

[@indrajeetsingh37]

Sir, if I reduce 1.5 inches reduce rider seat foam cushion, for low seat, will it comfortable for short rider, or which type of impact goes to our body

[@RajkaGarage]

I would suggest not to do that, as it will make the seat hard on the butts and can lead to other problems like riders butt (constant pain in the buttocks).

[@indrajeetsingh37]

@@RajkaGarage thanks sir,

[@AJ-Tech4U]

Hi, where did you get the bar ends.

[@derekdrakeful]

Hey, is that a Yamaha RD 350, next to the CB350?

[@prabhakarchauhan907]

Hey Raj , does this increase stock mirror visibility? Please confirm

[@RajkaGarage]

Not really. To increase the mirror stalks height you can use the studds used in any Activa mirror. These are small 1" extenders used between the mirror and the yoke.

[@kanthanind]

Installed the same. But some stretch in brake hose. is it ok?

[@RajkaGarage]

Minor strech is Ok. Also once you sit on the bike the fork pipes will tend to move down giving some more breathing space to brake pipe.

[@kanthanind]

@@RajkaGarage thank you

[@suhaswankhede5453]

How has been your experience so far after having installed it?

[@RajkaGarage]

It very comfortable buddy, though the straight ones are only 1.5" in height it improves your reach to the handle. I no longer have the stretch my hands while doing a full turn.

[@indrajeetsingh37]

My hands are short, my hight is 5.5, can I use handle bar riser, inclind or simple riser T

[@RajkaGarage]

I am about the same size as you buddy with a proportionate upper and lower body. The straight ones are doing the job well for me. The inclined ones are further better but needs re routine of clutch cable and will have some stress on the wiring harness.

[@indrajeetsingh37]

@@RajkaGarage thanks sir

[@svkr521]

how about inclined raisers

[@RajkaGarage]

Inclined riser are even better, but needs re-routing of clutch cable. In my personal view, I don't like that aspect, cables dangling from outside of fork pipes. Also haven't practically seen the strain on other control cables. CR folks says it has no issues. As for me, the straight ones have surely improved my riding posture.

[@svkr521]

@@RajkaGarage Thanks, Even I'm worried about rerouting of cables to go for inclined raisers as My height is 5.6 (167cm), can standard raisers help for my height? Regarding price, I agree, carbon racing all the items are expensive. Unfortunately no other alternative.

[@RajkaGarage]

I am of the same height of yours with a balanced length upper and lower body. So the straight ones have definitely helped me a lot. Would have loved to do a test on inclined ones to see the strain on control cables, but CR wants me to invest buying which I feel is not worth. I buy, they benefit.😁

[@karthikjason2461]

Sir do u have any power cut off while changing the gear from 2nd to 3rd

[@RajkaGarage]

No buddy, no such issues since last almost 2 years.

[@ratneev]

On road price

[@RajkaGarage]

It was 2.26L in Mumbai in November. I guess it's increased since then by appx 4k

[@sangamp6292]

I doubt that's comfortable. Your wrist n shoulder might experience pain.

[@RajkaGarage]

No buddy.. it makes the ride much much better. Handlebar risers makes things comfortable is universal experience. Btw.. recently installed the inclined risers and that has made things further comfortable.

[@_anandu.vishnu_]

The headlight is very bad in rainy days 😔 any suggestions bro?

[@_anandu.vishnu_]

Bro?

[@RajkaGarage]

Yes, it's very bad, even without rains on highway. That's why I installed aux lamps on bike. Check this out. kzbin.info/www/bejne/Y6TagJmfgpeXo9U

[@_anandu.vishnu_]

@@RajkaGarage thnx bro

[@VlogsReviews]

You got the bike manual? You can adjust the beam actually, I read the manual on first day while bike is being serviced for delivery and got it adjusted right then. Taking delivery after 7pm I rode back home 220kms from Hyderabad. I had no issues 😊. Ps ; I have glasses (eye sight) + i wore helmet with visor on.

[@kapilohar1]

Avenger 220 cruise don't need such handlebar risers

[@aslambabu673]

sr what is the golden color materiel

[@RajkaGarage]

I have done golden wrapping on the fork pipes. These wrap papers are available with people who make radium Number plates.