Some advice for everyone trying to attempt this on your first time. Take your spark plugs out of your head. The reason why is when you go to rotate the engine over with the old belt on to get everything aligned with top dead center, it is much easier to do so when you are not fighting the pistons compressing in the cylinders. If you do not, when you try rotating the engine with the 19mm crank bolt you will hear the engine hissing as the compressed air escapes out of the valves. There is nothing wrong with it, that is how an engine sounds when turning half an RPM lol. But with the spark plugs out, the pistons and crank are free to rotate with minimal resistance. The only thing that will offer resistance other than the ever so slight drag from the actual friction of everything is the valves in the head compressing. Taking the spark plugs out just makes everything much easier to align. Obviously afterwards you need to put the spark plugs back in once the new timing belt/water pump are installed.
@shamandarnell6 жыл бұрын
Just a few side notes to anyone doing this for the first time. If you Don't have a good impact pick up the crank pully tool and an extra breaker bar, if the space is too small remove the bolt from the rear motor mount and have the engine on a jack it gives you a really good amount of free play, I prefer to remove the driver side mount bracket as it helps with getting some bolts, one you have everything out clean the side of the block its not worth the risk of some shredded rubber getting into either your water pump pulley or idlers making them seize, and finally before you re torque the crank bolt turn the motor over a few times and make sure it stays in time. As always the prelude love on this channel is just amazing. It sucks to have it down for so long but some great content came out of it, thanks Trey see you in the next one!
@treybedipping17346 жыл бұрын
Great added info bro thanks and thanks man see you on the next 1.
@youtubechangedmyname6 жыл бұрын
I have a 3/4 Snap On impact and it won't even break the crank bolt loose 👎
@cptn_shankz4865 жыл бұрын
Is the crank bolt a regular thread or reverse thread?
@jimeeatc5 жыл бұрын
@@cptn_shankz486 Its normal thread. Counter Clockwise to loosen. Also, the motor spins the same direction.
@zhingy6 жыл бұрын
This video came just in time! There’s first cold night and temperature is -6 celcius outside here at Oulu, Finland and my timing belt is 6yrs/90tkm driven 247/365 between -25 and +35 😄💣🇫🇮 Thanks for all the quality stuff and positive energy! 🤟 keep it coming
@treybedipping17346 жыл бұрын
Hope it helps bro
@Saisei875 жыл бұрын
"You don't know how to take the wheel off, heh, you prolly shouldn't be watching this video" Dead.💀💀💀💀🤣🤣🤣🤣🤣
@treybedipping17345 жыл бұрын
Lmaooo
@johnriddle58535 жыл бұрын
Trey Be Dipping can I use a H22 distributor for my f20B
@treybedipping17345 жыл бұрын
@@johnriddle5853 yizzzirrrr
@cbdreamer17094 жыл бұрын
So funny!
@KookiDowg4 жыл бұрын
I have both the physical and digital factory service manuals for this which works fine but it's good to see the process first-hand. Thanks. This was done on an H32A VTEC (Blue Top) for whoever is curious. The process is exactly the same and most parts are interchangeable with obd1 and obd2 H22 motors except the thermostat cover and thermostat itself due to the bigger diameter that the JDM H series motors have.
@elysiumvocalcovers38385 жыл бұрын
Man I just found out that I snapped the timing belt on my 92 Prelude today. And I was really bummed, but it’s awesome that you made this video on the same gen Prelude as mine and it’s very helpful. Much love bro! 🤘
@treybedipping17345 жыл бұрын
Sorry to hear that bro.
@EFNRND4 жыл бұрын
Did you bend any valves? I just snapped the timing belt in my lude and I’m wondering if I need a new head?
@elysiumvocalcovers38384 жыл бұрын
Kyle Lloyd indeed I bent valves, in cylinders 2 and 3 to be exact, but most likely yes, the h-series engines are interference engines, so basically your pistons and valves are very close together. So just get a new head and timing kit and you should be good to go, sorry to hear about that though man!
@EFNRND4 жыл бұрын
ElysiumVocalCovers ahh damn lol. Thanks for the reply. I was hoping I might get lucky and not have to replace the head. I snapped a timing belt on a b20 before and I just put a new belt on and everything was good.
@elysiumvocalcovers38384 жыл бұрын
Kyle Lloyd yeah I’ve had the same thing happen with my b16 lol those engines are stout and non interference if I remember right. But yeah h series engines are pretty fickle imo
@toki896664 жыл бұрын
Before watching: I wonder if he will say to turn the exhaust cam 1 tooth advanced/forward/counter clockwise that way when you slip the belt over the exhaust cam gear and the intake it will rotate the E. Cam backwards 1 tooth and into alignment. It was quite frustrating before I figured this out!
@detonationpyrotechnics41566 ай бұрын
God damn when he did the open hood shot I believe I grew an extra inch
@mr.horse18014 жыл бұрын
Bought a 97 w possibly a bad motor for 300 buks. Im doing the timing just to be safe because i found a shredded balancer belt and the timing belt walked a little. Waiting on new belts and the manual tensioner. Video helped a lot with finding the correct timing marks. Wish me luck that it starts. Nice lude btw
@treybedipping17344 жыл бұрын
Thanks bro and glad i could help
@mr.horse18014 жыл бұрын
Trey Be Dipping well it worked!! Belt came in the mail finally!! Took me forever and a day to get the timing right. Its way harder than it looks. But i have a running prelude!! Total investment 400$ so far. Thanks for all your help and ill be watching your vids as i start the restoration!!
@treybedipping17344 жыл бұрын
@@mr.horse1801 glad i could help bro.
@jasonlintner94083 жыл бұрын
You a smart dude Trey ur vid saved me at work ☝️☝️🦾💯
@treybedipping17343 жыл бұрын
Glad i could help bro💪🏾
@andresgarcia58505 жыл бұрын
That lude is so clean
@treybedipping17345 жыл бұрын
Thanks bro
@willthecardude69004 жыл бұрын
Thanks man, finally a video where I could see how things go together.
@FinMcMurder4 жыл бұрын
Got my fogs in and now doing timing. Thx for the easy tutorial!
@treybedipping17344 жыл бұрын
No problem bro
@lilx4414 жыл бұрын
Rebuilding my a4 out of the car currently just got a new crank and bearings all the timing belt jazz but was wondering about those “Honda guidelines” they always have some tension tricks to keep an engine in time, had the somewhat the same concept on my y8 awhile back. thanks for the info! Subbed!
@treybedipping17344 жыл бұрын
Anytime bro
@troyhelton41012 жыл бұрын
How did you get the timing belt on with all the tension that is already there? Is there a way to loosen the tension to get that belt on while try to keep the pulleys top dead center?
@Ev3ryDayAnswers5 жыл бұрын
How tight is the belt supposed to be? In other words how much movement should there be?
@twitch_thepd9256Ай бұрын
How are the gears supposed to be for the second belt? Top dead center on those too?
@orlandomorales65654 жыл бұрын
On this manual tensioner I see there’s the tensioner bolt but also there’s one we’re it slides too also it’s a 10 mm long bolt connect to to the water pump tho I need to install it also on your video it’s hard to see if you hade it but I don’t see it
@jeromebrooks68673 жыл бұрын
My temperature gauge a my fuel gauge just went out I got to order that today
@paulmiller58744 жыл бұрын
So to set the timing I need to have the cam arrows in both up positions and the crank has to be aligned with the notch?
@rollthelosingdice4 жыл бұрын
disregard the hydrolic tensioner, get a k-tuned one.
@bb6g1345 жыл бұрын
Nice man! I hate how tight the area is to do Timing job on Prelude’s, gave me busted knuckles haha
@2011trdyota5 жыл бұрын
BB6 Builds lol preludes are lucky, try doing it in a h2b swapped car lol
@brunostroszek39284 жыл бұрын
just picked up a 94 Si with 103k original on it and need to do this soon. think i can manage it if ive never changed a timing belt and water pump, or be careful and pay a shop?
@Tristan-kd7ck5 жыл бұрын
How did you tighten your manual tensioner? I'm very stuck and my timing belt keeps slipping from the gears when I turn the crank shaft pulley.
@treybedipping17345 жыл бұрын
Which tensioner do you have? Its pretty simple to use just turn counter clock wise to raise it up and that tightens the tension.
@Tristan-kd7ck5 жыл бұрын
@@treybedipping1734 h23 ks tuned manual tensioner. What kind of method did you use to tighten it becszue I'm using a crows foot and some extensions. And I still cant seem to tighten it.
@treybedipping17345 жыл бұрын
@@Tristan-kd7ck it should have come with a special wrench. If not use a short wrench and as you turn, flip the wrench over to get the next angle to turn it.
@erickilpatrick44404 жыл бұрын
Great video! Thanks for taking the time to put it together!
@treybedipping17344 жыл бұрын
No problem bro glad it helped you.
@gracien2008 Жыл бұрын
Mine snapped while at idle... so im replacing timing belt and pump. How did you do all that with that engine mound still attached?
@treybedipping1734 Жыл бұрын
You have to remove the mount to get the new belt on
@Bolito_electric Жыл бұрын
The cams just up and the other in the mark?
@grimmcharest81026 жыл бұрын
Very nice, the h22 kit is also used for the f20b ? i havent been aware of this
@treybedipping17346 жыл бұрын
Almost all h22 parts are interchangeable with the f20b aside from some internals.
@elmazmaliante20103 жыл бұрын
F20b h22 and h23v pretty much the same
@dylancoonrod3994 жыл бұрын
Very helpful thanks im a little more confident in changing my h22a4 5th gen
@treybedipping17344 жыл бұрын
Glad i could help bro
@CRay-yq8se5 жыл бұрын
Thanks for video Tre. U got some clean rides. I subscribed to ur channel, looking forward to watching everything u got on the prelude. I saw urs is turbo, so I assume you sleeved the engine ect....hope u got how to on that for future dreams of mine🤫. Tell them advertisers to up ur pay before you blow up and they can't get a spot!!
@estingovender22365 жыл бұрын
Good day. I have a H22a1 1992 Honda prelude. I have replaced my timing belt and everything works properly except for my belt getting shredded against the two tensioner wheels. I'm not sure if I put the crank timing pulley correctly or could it be something else. There is a big washer which I put behind the timing crank pulley;not sure if it should go in the front of the pulley. And how far back should I push the crank timing pulley. Reason I am asking this is due to no Honda macs in the area and I have to fix it myself. And people are clueless in my city.
@treybedipping17345 жыл бұрын
Tensioner may be too tight
@princesalyavictoria49795 жыл бұрын
the question is..how a bout cam gear ajustable racing h22a..can we used to..for f20b dohc..?? Thanks..answer please..
@treybedipping17345 жыл бұрын
Yes it can be used for the f20b
@princesalyavictoria49795 жыл бұрын
Thanks..sir..
@tabasamashfaq16802 жыл бұрын
Thanks for this video champ!
@estingovender22365 жыл бұрын
I snapped my cambelt. Can I set trimming without the belt on.
@treybedipping17345 жыл бұрын
Typically you have to set the timing with the belt off and once the timing is set you install the belt.
@davidmerriweather96785 жыл бұрын
Estin Govender how did you re time the cams and crank
@gamingwithroxy12264 жыл бұрын
I have a ?. So the mannul tenensor is on. So does that mean I can by pass the balancer pullys.
@Sergio.Muresan2 жыл бұрын
Great video, thanks for this. I have a random question, what are those markings on the Cam Caps at 12:58? What do they represent? I have an '99 F20b, took the valve cover off and have the same markings on ALL the caps, only mine are 45 / 107. I also have a JDM '93 H22a and it doesn't have these markings.
@Sergio.Muresan2 жыл бұрын
Any idea on what the markings are?
@Sergio.Muresan2 жыл бұрын
??
@miguelroybal30282 жыл бұрын
Yo I replaced my water pump an thermostat an did everything in ur video an it still don't wanna start
@treybedipping17342 жыл бұрын
What makes you think the timing belt is keeping it from starting? You need to check for fuel, spark, and compression
@donalbaincharamba29032 жыл бұрын
sup bro I'm from Zimbabwe my prelude is boiling there is pressure build up in the engine how do I solve that do I change the head gasket love your work. by the way
@treybedipping17342 жыл бұрын
Try removing you thermostat first and see if that solves the issue. If it does then just replace the thermostat. It's a cheap part
@donalbaincharamba29032 жыл бұрын
@@treybedipping1734 getting parts this side is really tricky any reliable shipping companies to Africa
@treybedipping17342 жыл бұрын
@@donalbaincharamba2903 ok then just remove it for now.
@donalbaincharamba29032 жыл бұрын
@@treybedipping1734 sorted bro thanx a million now have electrical issue
@bobbydelamar6065 жыл бұрын
Great video. I have the KS Tuned manual tensioner on my 1999 Prelude.
@mrkeithleeman19983 жыл бұрын
I took my belt off last night to replace and didn't set It to TDC. None of the gears have moved. Can I Install the new belt and rotate the engine to TDC and make sure everything lines up properly?
@treybedipping17343 жыл бұрын
Not worth the risk i would do it the right way.
@mrkeithleeman19983 жыл бұрын
@@treybedipping1734 Thanks for the reply. But I'm kinda confused lol. Do I put the new belt on and slowly rotate the engine until the crank marks line up and then check to see where the cam gears are?
@treybedipping17343 жыл бұрын
@@mrkeithleeman1998 the 2 cam gears as well as the crank all have marks indicating when the motor and cams are at top dead center. Once they are tdc then you put the belt back on.
@mlawsin20005 жыл бұрын
Can u do a video on how to swap out pulleys from your prelude? My prelude is squeaking and it’s pissing me off....
@treybedipping17345 жыл бұрын
That one is easy bro. You take the power steering belt and pully belt off. Then you need a really strong impact gun and just zip it off i could do that entire job in like 15min
@jamiuusman42839 ай бұрын
Please help me out my timing belt cut when I'm driving the car what is the number of the timing
@treybedipping17349 ай бұрын
Link to the kit is in the description
@ninamusik55674 жыл бұрын
Which marks on a flexplate(AT)/flywheel (MT) do you use to align ignition time
@nickengle47654 жыл бұрын
Care to share what turbo manifold that is? I only know of one on the market that lets you keep the stock alternator location.
@treybedipping17344 жыл бұрын
Custom bro.
@calebross80044 жыл бұрын
yo i need big help, so basically i have an h22 in my del sol. I got everything to TDC while the belt was on (so everythings in the same rotation)but when i took off the cam gears they moved forward slightly now its not TDC. To get it back TDC I know 1 rotation of the cams is equal to 2 rotations of the crank but what is the calculation for the "balancer gears" for them to be in time with the crank?
@treybedipping17344 жыл бұрын
Everything has marks. There is also a service bolt in the back of the block to lock the balance shaft gear in place
@jamieotinger73 жыл бұрын
If I snapped my belt did it hurt my valves or Pistons been told that it doesn't hurt them on this particular model
@treybedipping17343 жыл бұрын
Its case by case cheapest way to find out is to put a new belt on and if it runs like crap you prob have bent valves
@miguelroybal30282 жыл бұрын
Where u located at I have a 1999 Honda Accord ex with an f20b JDM engine I having timing issues
@treybedipping17342 жыл бұрын
I'm in Virginia
@calebross80044 жыл бұрын
Hey i was about to order the kit you linked, I’ve seen some bad reviews I was wondering what was your experience with it?
@calebross80044 жыл бұрын
Also thanks for replying to my last question
@the1chevyman5 жыл бұрын
So h22 and f20b have same belt, tensior, bearing, water pump? Please answer ASAP thanks.
@treybedipping17345 жыл бұрын
Yes
@financetips2 жыл бұрын
Did you answer ASAP. Oh some viewers are demanding 🤣🤣🤣
@fredyr11254 жыл бұрын
You don’t get belt woble?
@braydencrawford30484 жыл бұрын
would a light weight pulley kit install be a good idea?
@treybedipping17344 жыл бұрын
Never used one so im not sure bro
@justanotherguywithtime1926 жыл бұрын
hey man im Ian le osten on facebook Congrats on her saying yes
@treybedipping17346 жыл бұрын
Thanks bro i actually have a video dropping on that so shhhh lol
@mrmuller61316 жыл бұрын
haha too late😂
@aloioh22725 жыл бұрын
Bro i installed manual tensioner on my h22 but I have a lot of slack between the cam gears. Did I miss something? I made sure everything aligned with the marks.
@treybedipping17345 жыл бұрын
Once its timed correctly you turn the pully bolt 3 teeth counter clockwise to create tension. Then then you adjust the tensioner to remove thr remaining slack
@aloioh22725 жыл бұрын
@@treybedipping1734 thx a lot bro
@Johnynfs4 жыл бұрын
When u turn the crankshaft with the belts on at the end counter clock wise three teeth,is it okay for it to move of the tdc points all together?
@treybedipping17344 жыл бұрын
You have to move all of it at the same time to keep it it in time.
@nicklopez22866 жыл бұрын
Nice video man. Very informative 👍
@JamesStephen5 жыл бұрын
good video man! I've been putting off changing my cams for ages but it looks easy now I've seen how
@treybedipping17345 жыл бұрын
Yea its not that bad
@suckinmesince19976 жыл бұрын
Bruh thanks for the kit link needed that
@treybedipping17346 жыл бұрын
No problem bro, you know im here to help.
@bernardnambwe7753 Жыл бұрын
Mine is not acseleleting after the belt change what can be the probrem
@treybedipping1734 Жыл бұрын
It nearly impossible to diagnose anything over the internet bro....to many unknown variables
@javierchavez71673 жыл бұрын
What do you mean about top dead center about the cam gears cause im about to change my cam gears
@treybedipping17343 жыл бұрын
When the pistons in the center are at the highest point it can be in the block. Its a term used for reference when timing the motor with new belt instals
@h22eh64 жыл бұрын
I got a f22b damn world of hurt finding a water pump for it
@treybedipping17344 жыл бұрын
No luck at auto part stores?
@h22eh64 жыл бұрын
Trey Be Dipping not for a jdm f22b shit is different
@v-tecflavoredrice43205 жыл бұрын
Ayo bro whatd you put the jack on to jack 1 side of motor up a bit to take mount off to slide new belt on?
@treybedipping17345 жыл бұрын
Oil pan...just be careful
@kristenholman38332 жыл бұрын
Your cool 😎 straight forward great 👍 job
@treybedipping17342 жыл бұрын
🙏🏽🙏🏽🙏🏽🙏🏽
@notyourproject83154 жыл бұрын
where is that 12 mm bolt you mentioned for the alternator tensioner?
@treybedipping17344 жыл бұрын
The tensioner bolt is a 10mm there is a 12 under the alternator that tightens it and holds it in place.
@notyourproject83154 жыл бұрын
Trey Be Dipping thank you so much i been at this step for a while 😂
@1drmr34 жыл бұрын
So my intake can gear is about 2 teeth off. Im trying to loosen the timing belt so I can move the cam in place but all I can find online and KZbin is timing belt removals or water pump replacement or adjustable cam gears like I just need to loosen the damn belt so If anyone can guide me to a video I would appreciate it
@sumfoo58714 жыл бұрын
There are some rings that come with it. Do thwy go with the tensioner? Theres 2 of the same size and one that is bigger
@treybedipping17344 жыл бұрын
Im not sure what your talking about. Message me on instagram.
@enriquevalentin2814 жыл бұрын
I think your talking about the camshaft seals and crank pulley seal
@lukehertzog79585 жыл бұрын
Can you put in the manual tensioner without resetting the timing
@treybedipping17345 жыл бұрын
Yes its possible
@lukehertzog79585 жыл бұрын
Any tips my belt is fairly new
@gyfyasdugcuxjftsdvfb4 жыл бұрын
Thanks for taking the time to make this video I'm gonna try to do it this summer on my 97 lude. Hopefully I wont have too many questions for ya
@treybedipping17344 жыл бұрын
No problem bro
@jamiuusman42839 ай бұрын
What is the number of the timing belt?
@elmazmaliante20103 жыл бұрын
Bro i have a question in my case i like race so in your opinion is good cut the balance shaft belt for more strength or is not safe cut it? What could b pros and cons?
@treybedipping17343 жыл бұрын
Ks tuned sells a balance shaft delete kit but you can also just not run that belt
@elmazmaliante20103 жыл бұрын
So that can't cause any issue? sorry for boder u bro is just i wanna make sure so i can and nothing going happen?
@treybedipping17343 жыл бұрын
@@elmazmaliante2010 you will just have a little vibration nothing crazy
@elmazmaliante20103 жыл бұрын
Thanks homie a lot a follower here💪💪💪💪
@elmazmaliante20103 жыл бұрын
Thanks a lot my man...i really appreciate your tutorial and thanks again for sharing w/ us
@liamsvideos21479 ай бұрын
Is it just me or is It jacked via the sump
@treybedipping17349 ай бұрын
Wlthe car?
@orlandomorales65654 жыл бұрын
How can I get the cams in the correct timing if they were move while the belt was off
@treybedipping17344 жыл бұрын
There are arrows and line notches on the cams and crank to guide you to put it at top dead center.
@orlandomorales65654 жыл бұрын
@@treybedipping1734 so as long they are set in marks it wouldn’t mater if they were move just move them to the marks and that’s all..also with this manual tensioner how can I get the correct tension on the belt with out the noise on it I used my car for driving not racing will it still be better to go with the manual one
@treybedipping17344 жыл бұрын
@@orlandomorales6565 i explain all this in the video 🤣
@rollingbatenz3933 Жыл бұрын
No how many teeth between the to arrow marks plz bro been told 13 12 and 14
@treybedipping1734 Жыл бұрын
Not sure what your asking. The arrows on the cam gear indicate top deaf center when they face straight up
@kaylieconner86315 жыл бұрын
any special equipment needed for this?
@treybedipping17345 жыл бұрын
I guess that depends on your definition of special but nothing out of the ordinary
@davidmerriweather96785 жыл бұрын
Yo. Need help. My timing belt snapped. How do you re align both cams. My intake side is more advanced than the other
@treybedipping17345 жыл бұрын
Turn it with a 14mm wrench or ratchet
@davidmerriweather96785 жыл бұрын
Trey Be Dipping got it I was panicking thou haha. Counter clockwise right?? Shld I line up crank first then cams. Correct?
@treybedipping17345 жыл бұрын
@@davidmerriweather9678 yea either way make sure its top dead center at the crank and the arrows are facing up on the cams.
@davidmerriweather96785 жыл бұрын
Trey Be Dipping okay so.. intake side doesn’t turn hella smooth lik exhaust side. Like you start turning it and it kinda just clicks in place about 1/4 full rotation,, You can’t make small rotations. Counter clockwise
@treybedipping17345 жыл бұрын
@@davidmerriweather9678 try adding oil across the cam and move slow its like balancing
@DIRTYSANCHEZ9172 жыл бұрын
What is the average time it takes to do this?
@DIRTYSANCHEZ9172 жыл бұрын
@Trey Be Dipping
@treybedipping17342 жыл бұрын
@@DIRTYSANCHEZ917 it depends on your skillset but I would say on average 4-6hrs
@jamesstewart1794 Жыл бұрын
Did you use an H22 belt on the F20B
@treybedipping1734 Жыл бұрын
Yes sir
@jamesstewart1794 Жыл бұрын
@@treybedipping1734 reason I ask is I've been told the h22 belt goes on too tight but apparently having the manual adjusted tensioner helps.
@treybedipping1734 Жыл бұрын
@@jamesstewart1794 they say there is a one tooth difference but I've never had any issues
@jamesstewart1794 Жыл бұрын
@@treybedipping1734 so did you use h22 water pump too , right ?
@jamesstewart1794 Жыл бұрын
@@treybedipping1734 h22 water pump too ? I'm about to swap from an h23a Bluetop to the F20B soon so I wanna make sure I have the correct parts to do the belt and water pump before the motor goes in since prelude have such a tight engine bay.
@micc40445 жыл бұрын
Bro where can I get a service manual like the one you got??
@treybedipping17345 жыл бұрын
Man i got it as a gift from my pops when i was younger and but i would try amazon.
@price55603 жыл бұрын
Service manuals can be found online 🆓
@orlandosouza33226 ай бұрын
Great info
@johnfarias72305 жыл бұрын
How the f$$$ did you get the belt on I have been trying for 4 hours to get the belt on it is so f$@#@ tight I have the shop manual and I built the whole engine damn
@treybedipping17345 жыл бұрын
There are a few tricks but you can try loosening the 14mm bolt holding the tension arm.
@johnfarias72305 жыл бұрын
@@treybedipping1734 yeah it was freaking tough I did manage to get it on I loosened up the tension arm and slit on that way but yep that's correct thank you for your info now I'm trying to figure out how to bypass the immobilizer
@eskater____16575 жыл бұрын
How do you tight the belt crank shift belt
@treybedipping17345 жыл бұрын
The balance shaft belt? You create tension by hand pushing upward on the circle tensioner or you can use a flat head screw driver as a pry bar as well.
@gallolinks5 жыл бұрын
Would it apply to a h23?
@VashRain1926 жыл бұрын
Eyyy dude, in a stock 5th I got the ABS Shit all in the way, what's a good way around it or do I gotta undo it all
@treybedipping17346 жыл бұрын
Abs is tricky to do a full delete you may need to redo some lines but most importantly you need a non abs valve from either a prelude, civic, or integra because once you take out the abs unit you'll have 6 lines that need to be regulated.
@VashRain1926 жыл бұрын
Cool, I'll have to look more into that then, I hate having it in the way. Did you do a delete or did yours not come with abs?
@treybedipping17346 жыл бұрын
@@VashRain192 i did a delete on mine. Free'd up alot of space. Way cleaner look.
@VashRain1926 жыл бұрын
Cool, I plan on it with mine as well. Gotta do the belt and pump on mine soon
@treybedipping17346 жыл бұрын
@@VashRain192 well hopefully this vid gave you a refresh for when you do yours.
@arthurgilmore38284 жыл бұрын
What kind of wheels are those
@treybedipping17344 жыл бұрын
Square wheels
@SvoBrianRobles5 жыл бұрын
Can you remove timing belt cover with out removing valve cover ???
@treybedipping17345 жыл бұрын
Ehhh its possible but it wouldnt save you any time tho
@johnriddle58535 жыл бұрын
Trey Be Dipping can I use h22 distributor for my f20B
@treybedipping17345 жыл бұрын
@@johnriddle5853 yes sir just bee aware if its obd1 or obd2
@johnriddle58535 жыл бұрын
Trey Be Dipping How do I know if it’s OBD1 or OBD2 it’s in my 95 accord sir
@johnriddle58535 жыл бұрын
Trey Be Dipping my rpms are hesitant and kinda jumpy it don’t have its full powerBut when vtec hits it has power I think it’s the sensor in the distributor have any suggestions?
@jasoncapps23325 жыл бұрын
What part numbers or kit is it?
@treybedipping17345 жыл бұрын
Link is in the description.
@azvasamusic70954 жыл бұрын
YO HAS A GALAXY UNDER HIS HOOD
@lelakisejati44563 жыл бұрын
how tight the tension are?
@jamesstewart1794 Жыл бұрын
Yes
@v8vairv8vair4 жыл бұрын
Thank you so much
@jmac40135 жыл бұрын
How long did this take you?
@treybedipping17345 жыл бұрын
About 3-4 hrs but thats with recording too.
@jmac40135 жыл бұрын
@@treybedipping1734 Have you ever experienced your car always wanting to stall out once the engine gets warm? If so what causes this?
@treybedipping17345 жыл бұрын
@@jmac4013 depends in some cases the throttle cable needed to be adjusted or bad tps sensor
@jmac40135 жыл бұрын
@@treybedipping1734 thanks man, that at least gives me some direction to start looking
@5thgearedlined4 жыл бұрын
Well done 👍
@h22eh64 жыл бұрын
What are those wheel specs bro
@treybedipping17344 жыл бұрын
17x9 20mm offset
@h22eh64 жыл бұрын
Trey Be Dipping tire specs to plz
@treybedipping17344 жыл бұрын
@@h22eh6 205 40 17
@calebross80044 жыл бұрын
What tool do I use to turn the Timing belt so it’s top dead centre?
@treybedipping17344 жыл бұрын
For the bottom put the 19mm bolt back in so you can turn the crank. The cam bolt is a 14mm
@mmlindsey86356 жыл бұрын
YOU DO IT'S ALL. NOT BAD KINDA GOOD
@JuanGarcia-ys3rr2 жыл бұрын
Man you didn’t even show how tp put the belt on
@rtrueblooda5 жыл бұрын
Trey, can you work on my prelude? Seriously tho lol
@treybedipping17345 жыл бұрын
Yes sir just let me know
@rtrueblooda5 жыл бұрын
@@treybedipping1734 I got a 93 prelude so back in like 2013, I swapped the h23 with an h22a1, it's been like 6 years and I still can't drive it lol the bb2 is my dream car so I've kept it around all this time. I love your channel, it would be awesome to get up with you, but I'm way down south, Houston, tx
@treybedipping17345 жыл бұрын
@@rtrueblooda yea bro if you can get the car up my way i would be more than happy to work on it
@fellowtraveler24955 жыл бұрын
Trey Be Dipping Are you from California?
@rtrueblooda5 жыл бұрын
@@fellowtraveler2495 nope hes in va
@Maverick2149726 жыл бұрын
Why dont you use gates timing belts performance?
@hattershouse7106 жыл бұрын
They aren't much better than oem if at all. I used one before and have one on my car as well.
@Maverick2149726 жыл бұрын
They're better than oem last me 5 years and going
@hattershouse7106 жыл бұрын
I sell them. They are nothing special. Years doesn't mean anything, miles is the determining factor. I had a stock timing belt for 6 years before the tensioner went out and i swapped out my motor. I have a gates on there now as a matter of fact on my h23a. I get them at wholesale cost and thats the only reason i chose it over oem. The belts are not "better", neither will "snap" unless never changed.
@badlilboy2325 жыл бұрын
Hey trey if my cam timing is off a tooth or 2, would I have to go through this whole process to get it back in time? I have a long screw driver in piston 1 and got it to tdc can I just slide the belt off and readjust the cam timing like that or not a good idea?
@treybedipping17345 жыл бұрын
If it skipped a tooth it could be possible is stripped the belt you may want to look replacing it. But yea there is no easy way to do it honestly
@badlilboy2325 жыл бұрын
@@treybedipping1734 well good to know there is no easy way. But your video definitely helps make it easier to do. I really appreciate the reply thank you fam!✌🏽🤙🏽
@treybedipping17345 жыл бұрын
@@badlilboy232 no problem bro ✊🏾
@kristenholman38332 жыл бұрын
Crankshaft balance belt
@robertrellstab9015 жыл бұрын
Did you reuse your tension Springs?
@treybedipping17345 жыл бұрын
I replaced the hydrolic tensioner with a manual ks tuned style but reused the one spring with the hook
@agix6664 жыл бұрын
i have a 99 prelude h22a4 with a shattered oil pump i have the motor mount out and the crank pulley off and the oil pan. do i have to remove the water pump and other gears (6:30) to get to the oil pump? i took a pic of what mine looks like rn imgur.com/a/8B6YGCa