Hoverboard Not Moving Troubleshooting Repair - Wheel Stuck, Mainboard Short Circuit Replacement

[@LucieneFernandes-sg6fg]

Thanks 🙏 first step worker 💯

[@paulreader8927]

Excellent clear concise video, thank you for the help..

[@metainstincts]

Glad you liked it!

[@SupremeGang420]

I have a problem with mine. My hoverboard has both blue lights and both green lights when I turn it on but when I put my feet on it, it doesn’t respond at all. I tried recalibrating it and it refuses to do so. I’m guessing it has something to do with the gyro sensor boards? Edit: replaced both gyro sensor boards with the new ones. The lights turn off but the board still doesn’t respond. It does respond to something being pressed on the pads though

[@JanDuToit]

Dude. Came here because the left foot was behind the right one on the incline. Didn't know about the calibration. Thanks

[@metainstincts]

try calibrate it

[@roseworld8091]

Great video!! I' d like you make a video repairing the motherboard,. Can you tell me the link to get the new motherboard?

[@peroimilanfan3768]

did you change anything or did you do a sensor calibration now 

[@metainstincts]

replacing the motherboard is the easier way

[@iezzif]

Got a question. Bought a used 10 in smart hoverboard and changed all the boards. I use it for a hoverseat. Cannot go up a small hill in forward but can do it in reverse. Is the problem related to the sensors under the footpads?

[@metainstincts]

It could be the hoverseat problem. It might have a problem to tilt the hoverboard.

[@OldSkoolF]

If you have a red flashing light on one side and it wont move and Recalibrate doesn't fix it... Check all plugs and wires are getting good connection (Especially the 5 wire sockets). If they are and it still don't move then it probly has a blown output fet on the side thats red. They're easy to change.. MAKE SURE BATTERY IS UNPLUGGED!! Measure the Mosfets, 6 on a heatsink per side(GDS)... Usually only 1 or 2 short... DMM to Diode, Neg on Center pin (Drain), Gate approx +1.5v, Source approx .5v. YST7575C crosses to RU6888R 68v 88a TO220 *** For this model Mainboard, one bank of Fets controls one side wheel drive. Do a continuity test to figure out what bank controls what side.. Each bank of Fets, are broken into pairs per thick wheel drive wire (YGB)..

[@abandarolex395]

I have a problem vvv different from this... ma mother board is fine I knw cuz the syd that was not working I changed the memory with the one that was bad and the bad syd worked while the good syd did not. So I concluded it's a memory pb. If changed the memories and it still dose not wok so am kinda lost... do any one understand me or one that am talking about??? If u do pls help

[@audrinaponce9767]

Thanks your video help my problem

[@marvinquisel9406]

hi'.i do reset..and still not calibrting..red light olwieS flashing..can u dterminewhat posible problem? thank you

[@metainstincts]

This could be circuit board failure

[@FredddH]

what is the type of connector to use on the hoverboard cables please? I would like to repair a broken cable without having to buy a card to have the cable. Thanks a lot

[@metainstincts]

I suggest taking the board to an electronic store, and ask for the cable. Every cable is different in the board.

[@khadijashahzad3769]

From where we cam buy new board

[@maliqmullaji]

Thank you. This worked

[@MTVBLOG..]

Il mio Hoverboard non funziona il movimento e rimane sempre acceso

[@raslenromdhani1674]

Can you link to me where did you buy the mainboard?

[@samburgess187]

How do you disconnect the green cases wires they're really hard to do and also where could I buy another main board?

[@metainstincts]

+Sam Burgess try rotate one of the connector. You can buy this new main board from here: www.coolwheel.my/index.php?route=product/product&path=76&product_id=210

[@amandaangel21ify]

What does two flashing dots mean? On my hover board

[@jdmfever2092]

Hey , please publish a new video abot the main board trouble shootoing ant some link for buy a main board

[@giovaniemadrigal4719]

do you repair hoverbords for other people and if so how much

[@metainstincts]

+Giovanie Madrigal Yes, we do hoverboard repair in Malaysia. Repair fee is depending on failure part

[@heartmomma6460]

Concept For All Wish you fixed in the US. You would be a millionaire in my neighborhood. ;-)

[@Taylor-fs6zu]

Yes. Wish he was in the US. Need to get my daughter's hoverboard repaired.

[@elshanagayev9882]

Good troubleshooting, how and where i can buy mainboard

[@rojonunez91]

what's the part that changed name

[@elshanagayev9882]

​@@rojonunez91 motherboard

[@TomyCroSound]

Please help! Koowheel hoverboard K1 started to work incorrectly. The first mistake was to stop the left or right engine at random, then suddenly turn off. I can not turn it on. I suspected the charger, but the charger is correct. I thought the battery was empty, but the battery was 36V. When I try to turn it on, the green light on it once lights up once. When I connect it to the charger, the loudspeaker is activated that the bluetooth is ready for pairing. The device shows charging, but charger does not. (Battery full) Can I safely say that the motherboard is incorrect, or can it be anything else?

[@metainstincts]

This is a battery defect sign, more than 70% China hoverboard have this defect, where they never QC on it.

[@TomyCroSound]

Concept For All .. but battery is 36V when measure..

[@metainstincts]

There could be 2 issues occurred concurrently according to your explanation. First is battery defect: if your hoverboard is suddenly off (completely off, no light, engine not moving, no sound) and can't turn on, it is because the protection board in your battery detected incorrect voltage between the battery cells and kick off the protection sequence. It protects the cell from damage and explosion. You can check the battery voltage at this stage, the voltage should be below 10V. During checking, DON'T disconnect the battery or it will reboot and back to 36V. You should touch the multimeter pins on the motherboard where the battery connection is connected. The hoverboard is unable to turn on at this moment unless you reboot the system by plugging in the charger or disconnect+reconnect the battery. Second is motherboard spoiled: If your hoverboard turn on by itself when you plug the charger in, the motherboard is spoiled. The hoverboard shouldn't turn on by a charger. If the hoverboard doesn't ON, but the speaker is ON, then the problem is probably due to wrong bluetooth power supply point connection.

[@TomyCroSound]

Concept For All Thank you! In any case, the new battery is 500kn (my currency), motherboard 700kn, and new K1 hoverboard 1000kn. 🤔

[@metainstincts]

We don't have battery for sales, but we do have the top grade motherboard at around 400kn. the motherboard is comes with APPS support and auto tilt features, and the circuit design is the latest and durable by TaoTao (authentic). If you are interested, you can look here: www.coolwheel.my/mainboard

[@akukuhillary3771]

Hello my hover board got a water splash now one wheel moving and the other not with a blinking red light, help

[@nafoooz2002]

i have one with 2 green light still light and not going to calibration and hoverboard blinking seven time that happen after wrong calibration

[@w.d.iibatteas4322]

for the beeping 7 times on the motherboard it means that you opened the hover board upside down I think

[@dapunza]

I have one that turns on and the red light flashes, I've watched every video and tried to re-calibrate several times, drained the battery recharged the battery and nothing! when holding the button it does flash the lights 5x just like some videos I watched but when I turn it off and back on the red light still flashes... =( I have another (Different model) that if you hold the power button it has a woman's voice that says, "Trying to connect Bluetooth" Bluetooth pops up on my phone and disappears, the thing never lights up or seems to turn on...?

[@metainstincts]

This could be the circuit board failure, you should try replace the circuit board. You can buy a good one from coolwheel at www.coolwheel.my

[@CiderPang27]

Count how many times it flashes. It will flash so many times then pause then flash again. Then google hover board flashing codes. The number of flashes will tell you what the problem is.

[@ChefSAINATTH]

Good,tq... My problem rectified in first step....

[@CamassaXL]

Hi. Thanx for the video. My green wire cause the problem on my one. Once i unplug it then my wheel is released. Can my mainboard get fix or i should buy another one? And how to specify the main board model? Thanx in advance

[@ivanurban2383]

Its probablly just a bad mosfet, they look like black rectangles with a metal bit. Use a multimeter and measure across each terminal, whichever one has a short is the bad one. They are located around the perimeter. They are easy to replace

[@ivanurban2383]

Sorry for being 4 years late

[@dustinplee5067]

My wheel on my hover board Is move the wheel it is bumping what is wrong with my wheel on my hover board and my hover board has a Blue light on it is that good or bad and the light is not blinking It’s a solid blue light

[@johnwaddell1609]

my daughter hoverboard is fully charged but wheels wont turn and how much would it cost to fix and the other thing is after a full charge it dose not take long until battery go flat again can you help me please

[@chrisbranaman6565]

Where can I get a repair kit that will fit a Swagtron T5?

[@metainstincts]

+Chris Branaman hi CHRIS, u need to open the casing and check whether the motherboard is the same type in the video

[@keontaebumpers6017]

Chris Branaman idk

[@miahopping7244]

Hi where do I buy another main board

[@metainstincts]

You can buy a best one from coolwheel at www.coolwheel.my. It comes with apps support and auto tilt features. Very useful

[@dmanbloom2107]

did you order the motherboard online. if you did what website

[@metainstincts]

+Dman Bloom hi, yes, it was ordered online. It is the authentic TaoTao motherboard with apps and dedicated Bluetooth speaker. Link here: www.coolwheel.my/index.php?route=product/product&path=76&product_id=210

[@gamingblackzone7959]

What is the price of Circuit

[@carlosazteca8441]

How much in average does it cost a brand new motherboard ??? this procedure is good also for a 19 inches wheels hoverboard ???

[@adhdproductions3989]

My hover board does not move and one of the pressure sensor lights doesn’t turn off

[@w.d.iibatteas4322]

this is the blue light of death please search about that

[@YaseenKhan-yk3qs]

Sir you can fix old mother board

[@keegygblouw5422]

My problem is I dont have this tipe of hoverboard idk this ones name he has a handel at the back and the has Bluetooth

[@johndurante2322]

Just fix mine and turned out my ground wire in wheel back board came off. I solder it back on and it worked. Y'all might wanna try removing motor magnetic wheel and check 4 thin wires and just weld it back on and lights go normal and both wheels will work without all the rest level junk

[@hassanharuna1067]

My hover board is beeping continuously never stop and is showing two red light

[@isaiahdeleonvlogs6593]

Hassan Haruna sane with my

[@Jimmy-rh5lk]

@@isaiahdeleonvlogs6593 u still struggling?

[@heartmomma6460]

Do you sell the blue colored mainboard? Part # 1537 JIN GANG LUN 2015-09-08? I hope it's not to old or an obsolete part? I could send you a picture to order it. Great video btw. Thanks.

[@metainstincts]

We only sell the top grade circuit board, manufactured by TaoTao, and they are compatible to most hoverboard. You can get it from www.coolwheel.my

[@willynepomuceno9482]

How much the board?

[@Levi.Gamer.FF1]

My hoverboard won’t move and won’t recalibrate and the lights are green instead of red it didn’t helped me 😭😭😭😭😭

[@CTG0716]

I’ve got the same problem, did you find how to fix it

[@darkknightr1716]

hello, nice job men, could you tell me why the tip 127 explode?

[@metainstincts]

It is due to poor circuit board design or component quality issue. It is normally happen to low grade motherboard

[@AngeloFonseka]

Tnx bruhh

[@aidanwatson661]

Mine dosent flash slowly

[@gerpinaroc2507]

How to turn off the hover board, sometimes when I will turn off the power, is still working,

[@malasweeanimation3806]

yes i want to know too

[@christopherhastings6714]

What is the name of that part that you have to replace

[@rockybay7022]

Hii brother can you give your any id to me i have a big problem of hoaver board can you solve it

[@rpWeb3]

why would you play music ONLY when you are talking?

[@user-iu3kz4hc5s]

My rigth side is slow how i do for that

[@inmaculadaahalvarezhernand1136]

Cómo reparar el patinete de balanceo raycul en español

[@kingjames2602]

the problem is the mosfet not the whole mainboard you need to replace 1 or 2 mosfet connected to the blue wire where the wheels is stuck do not replace the mainboard

[@jlovee2211]

thats a stretch, id rather replace the whole gyro board

[@LemonJuiceGV]

In 13 minute. I got tired of watching the video. Try changing the camera view to make the video more interesting then same old boring view.

[@mrpotatoman5678]

46e'/ ;vgtfr,./ thyjkl;mr tpooo meeef toov

[@FreakinKatGaming]

Well im all for repairing it but ill b damned if i could pull off the testing phase as the end. Lol then id hafto repair my kneck when i fall lol. Nice write up my friend

[@musujay8206]

please help me solve this my hover board with handle is not turning right or left what to do

[@loremarenerva4192]

what we do for may hoverbord the left side of may hoverbord is not moving pls.help me

[@johnnygalvan1344]

My green light won’t stay on ! It won’t stay powered on

[@mtvda230]

Please. Turn music offffffff

[@kingjames2602]

do not replace the whole mainboard just a faulty mosfet usually pair mosfet is the culprit

[@metainstincts]

Yes, you can do that if you have the tools and skill

[@MyNguyen-hz1gn]

you forgot recalibrate it again.

[@w.d.iibatteas4322]

but how is it stuck even when it is of

[@thankyoujesus2836]

You should disconnect the battery and drain the circuit before doing anything.

[@persianchris2451]

How do you drain it?

[@rahmanocawni5618]

​@@persianchris2451 hi he want to deplag the battery and discharge the capacitors so du can not distroy the The Mos fet transistors ok

[@dmanbloom2107]

what happens if the wheel gets stuck on the other side

[@metainstincts]

+Dman Bloom u need to unplug the wheel cables to check the problem, as illustrated in the video.

[@yolandamontes8466]

where I can fine tha part

[@bunivr3975]

Mine got messed up when I turned on my hoverboard upside down and then this happened it won't move

[@metainstincts]

It should work after you restart it. If isn't, u might want to try recalibration.

[@sfinxer3860]

Well my hover board got broken because I restarted it :( now it shows all lights on

[@aliyanaaz3075]

My hoverboard not moving

[@moodymoody4273]

my hooverboard starts only at max speed immediately. how to fix the problem?

[@2JZenvy]

Mine was water damaged and turns on but doesn’t move I’ll try it read my reply if it worked

[@metainstincts]

Water damage normally spoil the circuit board, replacing a new circuit board shall solve the issue. Make sure to dry the battery as well. You can get a good circuit board from www.coolwheel.my

[@ahmedahmed-rr5kh]

YOU EXPLAIN !!!!!! WHY MUSIC !?????? .NO NEEEEEEEEED

[@taqveenniexy2659]

Lol

[@Jordanfan779]

😢😢😢😢😢😢😢😢 now

[@RobertHarrisMIB]

You keep saying a main butt? Or a main button? Or member? What are you saying? I have listened to it a hundred times over and over and I have no clue what you are trying to say. Replace what? Remember, main button? Maine bott?

[@mhmd.x4533]

ز

[@mohamedamar7543]

t

[@aliyuabba4575]

Turn off stupid music

[@peterscotthoward]

The drippy hipster background music put me right off trying to listen to you