Hoverboard Wheel Rear Suspension E-Scooter Project

Hoverboard Wheel Rear Suspension for a Custom Electric Scooter project.
This video shows that is possible to DIY a rear electric scooter suspension to be attached to your E-Scooter project. An old mountain bicycle frame with rear suspension and a MTB rear shock absorber were used for this project.
Feels free to use your resources, tools and your creativity.
Please check my other video on how to fit a 120mm disc brake and caliper to a Hoverboard Wheel.
Parts used on this project are below:
MTB Rear Shock Absorber:
www.amazon.co....
Disc Brake Adapter 6 Bolts:
www.amazon.co....
Brake Caliper and 120mm Disc:
www.amazon.co....

[@barrysotero137]

Rad!.. (Going for it!.) Beef up those Tacked on Tabs (the ones taking the brunt of the force…The ones holding the Compression strut)

[@A_t_o_m]

Красавчик, жи есть, брат! За базар отвечаю! 👍👍👍

[@alextrezvy6889]

Will be glad to see your project finnished.

[@chibleecinematics3705]

I like your project

[@Attic-Toy-Design]

Thank you! Once I get find spare time, I will finish videos showing the lithium battery bank (36V 12Ah) main frame and the e-Scooter done and running…

[@gyankaurdung169]

VERY VERY GOOD SIR YOU ARE GREAT THANKS FOR KNOWLEDGE HARA KRISHNA

[@Attic-Toy-Design]

Thank you! 🙏 I hope I can find some spare time to finish the frame, batteries bank and upload some videos…

[@codebeat4192]

You don't need a break on a motor if you know how a motor works and what an electric motor can do by itself. Short two or all three wires together and try to turn the wheel by hand. By using low value resistors between the wires you can make a break.

[@R6marcus]

Can you elaborate on this a bit more please? I build scooters myself and your comment has my full and undivided attention. Thanks in advance.

[@matatisan]

looks great! keep uploading

[@fedemon76]

which electrode (type and thick) do you use with the 1.5mm thick profile and at what amperage?

[@erichocman7277]

Continu comme ça, très intéressant et interresser. J ai hâte de voir la suite.

[@Attic-Toy-Design]

Merci! Mon problème est le temps maintenant… pas le temps de finir… Je prévois de terminer l'intégralité de l'e-scooter et de télécharger la vidéo… Je vous tiendrai au courant!

[@геннадийзверев-д7й]

сварщик от бога;)))

[@trovaoag]

Perfect

[@fanaluckluck9237]

💓💓💓

[@mehmetusta9934]

kaynak işinde en az benim kadar ustasın

[@Attic-Toy-Design]

Thank you so much! I am trying to improve my welding…

[@alextrezvy6889]

07:25: How did you fasten the center bolt to the motor? How it is connected to the shaft?

[@alextrezvy6889]

OK, I've found the "Extra Axle" video.

[@Attic-Toy-Design]

@@alextrezvy6889 Awesome! I am planning to finish the scooter project soon. I'll upload the video and let you know! I hope my videos inspire you to achieve your projects.

[@Flo-mb9zg]

frage hast du Probleme das Wasser in den Motor kommt ?

[@paulstir]

I have a working hoverboard motor (tested on another system ) , I have purchased a brand new 36v controller with lcd ( s866 ) brand new throttle and brand new hoverboard battery for my e bike project but I'm experiencing no throttle issues I have checked voltage and purchased 3 brand new throttles checked wires tried swapping around but still no throttle

[@district99]

No update?

[@Attic-Toy-Design]

Hi buddy. Not yet…I am preparing 2 sets of video. One for the lithium battery bank and another one for the main frame.

[@sunilhardas1620]

मुझे बनाके मिलेगा क्या??

[@taureansdiy2132]

Looks like the angle of the shock to the pivit point is wrong. Shock won't be much help. Just saying.

[@Attic-Toy-Design]

Well, this is a prototype project. I would recommend to watch until I finish the whole e-scooter. I’ll keep you updated. Thanks mate!

[@Attic-Toy-Design]

The comments on your video is turned off but obviously I watched it and I can see you overload your e-scooter with 3 shock absorbers!! too much maybe..

[@taureansdiy2132]

Not really. The 2 motorcycle shocks are for the bounce and the center shock controls the rebound. Regarding the comment being turned off, have to check the settings. I'd love to see some comments on my video. Thanks

[@taureansdiy2132]

For sure I'll watch until the completion. 👍

[@ИльяБерезин-л6я]

Нормально

[@nelloalescio]

certi video si dovrebbero vietare,esguire un lavoro senza i minimi requisiti di sicurezza può spingere sprovveduti ad esecuzioni dannose e pericolose,per non parlare delle saldature e degli allineamenti dei profili,unica cosa buona forse l'idea