How a Clutch Sewing Machine Motor Works

[@mohdharissarun8226]

Hi..my singer industrial sewing machine ..motor unable to stop when i turn switch on...what is the problem?

[@tonyd8721]

Very difficult on machine to control speed, slowly push down, sometime run away speed, other times I can just get it right.. what does the bolt for adjusting position of brake do? At 1:20 of video.

[@sewway]

When you take your foot off the pedal, the brake pads clamp the pulley and the machine doesn't sew, although the engine is running.

[@yourkodi3945]

do u have a video on repair of this, or brush changes etc?

[@sewway]

Not yet, perhaps we will do it in the future.

[@anneeiler6182]

Thank you!

[@CorazonBDelacruz]

Myron po bang binebanta motor na ganyan kahit 2ndhan po

[@mirkotmusic7739]

Very informative. Do you have any advice on how to slowdown the machine without changing the pulley or motor?

[@sewway]

A very strange question. Do not press hard on the pedal. As a last resort, make a limiter

[@mirkotmusic7739]

@@sewway Thank you.

[@eduardogonzalez6331]

So the other guys said smaller pully the slower it goes but stronger the stitch

[@liaschmid1408]

This was very informative, thank you!!!

[@enriquevansen2260]

Thanks very helpful

[@Onesmus-pg3hg]

Can it provide power

[@andrewborozdin34]

Thanks for video, it really helped

[@sewway]

Thank You

[@brittanymuller6351]

What type of power chord does it use I got a PLK03BTA Mitsubishi it’ has a 220 v engine but does not come with cord

[@sewway]

For a 220 volt network, a three-core wire is used. Phase, zero and ground. But it is better to turn to an electrician for advice.

[@thirsamtg.nefertari]

Thank you ❤❤❤

[@ranger5705]

My motor started giving noise (like screwing with electric drill) when the pedal is released (un-pressed). Could you please tell me the reason? It was running fine for the last 15 years.

[@sewway]

There can be many reasons, most likely the bearing is worn out. But the main reason is age

[@marlenedavid6056]

Saan mkkbili ng motor ng juki or mag pa rewind

[@marvel_555]

I'm not a tailor but I need this for engineering. It's white in colour so I'm assuming this is the electrical machine right? Is this basically the same setup principle for the manual foot pedal machine. You apply enough continuous downward force on the pedal and it would cause a rapid steady rotation??

[@sewway]

Yes, an electric motor. By pressing the pedal, you compress the clutch disc and the engine disc together. The tighter they are pressed against each other, the higher the speed of rotation of the motor palley.

[@marvel_555]

@@sewwayPerfect, I appreciate it 🙏

[@syedasif4330]

Nice vedio 👌👌

[@shaikraheem5639]

I need moter clutch of this type how I should get

[@sewway]

Online sewing equipment stores sell

[@joeltorillo3577]

How much

[@chandranandani9230]

Galle thiyeada may motor eaka

[@estrangherojourney3082]

Mag Kano Ang motor Ng makina

[@undangmahmud2398]

Hmach pric

[@malred1497]

Traduire en Français merci beaucoup

[@johnmwangi9943]

When the pulley is small, the speed is low

[@sewway]

No, on the contrary

[@johnmwangi9943]

I installed a small pulley and the speed reduced, practical

[@sewway]

Exactly, you are right, it seemed to me the opposite.

[@murraymanning6682]

smaller pulley will make it slower not faster.

[@sewway]

Yes, that's right, in physics at school I had a bad mark

[@Hlonnygirl]

My motor is giving smoke

[@AftabAlam-tn7bp]

Clutchmotorindustrialaddress

[@AftabAlam-tn7bp]

Adress

[@AftabAlam-tn7bp]

Kanpurnagarupstate

[@sewway]

We don't sell anything

[@Цогооноо]

haha lol