How does an Inverter work? | Sine wave Inverter

[@ylstorage7085]

i AM VERY AHPPY WITH THE KZbin RECOMMEND ALGORITHM TODAY. THIS CHANNEL IS A GEM.

[@kuensenloh8305]

Awesome presentation through graphic. Much easier to understand and conceptualised how it works! Thanks !

[@agussuga5376]

Great video !!! Basically a sinewave inverter is a class D power amplifier with reference sine wave at the input and an output tranformer to increase the voltage to desired rms level (220V or 110V)

[@davidconner-shover51]

Most of the modern inverters use boost power supplies to crank up the voltage to 150 or 300VDC then drive the final output through a high voltage H bridge

[@jimmym2719]

You are awesome ! Thanks for a good explanations with lots of animations n diagrams 💕

[@vinitsingh8962]

Great video man. Appreciate your work and content.

[@rashedulislam1306]

Thank you so much for this video ❤️

[@BenyaminNetanyaho]

Very gooooooood😊😊😊😊😊Hello. Please explain how the Tesla coil works. Thank you❤❤❤❤❤

[@mpume.dzwane9213]

Nice seeing you again.

[@soorajpala]

Great video

[@DIYwithBatteries]

Thanks for REVEALING the schematic behind the Black magic :D

[@RenatoNagatomo]

I like how the transformer tries to connect to the circuit and is instantly blocked.

[@beanapprentice1687]

It’s to show that this is a dangerous high-voltage circuit that you should not build at home. Electroboom would be disappointed.

[@coucouj2781]

Yo noticed the same thing I did 😂... this tells me to just do it😂

[@frankgrudge8823]

Great video, love the 3d animation, though at times hard to visualise whats going on. A highlighted schematic would be easier to follow, love the videos and the content though thanks

[@te9781]

Question : Why do we need PWM ? Can't we just use a low pass filter and take the first harmonic sine wave from the square wave ?

[@beanapprentice1687]

Filtering a square wave into a sine wave would require huge capacitors and inductors, which would waste a lot of power in the form of heat as they repeatedly charge and discharge.

[@te9781]

@@beanapprentice1687 Thank you

[@skraja8752]

Thank you 👍👍👍

[@iitmeans-life6657]

Love you sir very very thank you 🙏🙏🙏 please make more videos to basic of electronic engineer

[@milanparmar6003]

Nice work sir..Please make videos on low pass & high pass filters

[@sudheerkumar5966]

Very good sir 🙏🙏

[@monimonish302]

Can you plz tell about the snubber circuit calculation and how to design and how it works

[@ExplorerStuff]

A snubber is a device used to suppress voltage transients in electrical systems. To suppress the transients, you need to store the energy and release it slowly. Hence, calculate the energy that needs to be suppressed (E). Then, select a max voltage that you want the capacitor to obtain (V). Energy stored in capacitor - E = C*(V^2)/2 -> Get the value of capacitance (C). And for resistor, Measure the max current current at the input of snubber circuit(I). R = V/I -> Get the value of resistor (R).

[@monimonish302]

@@ExplorerStuff tqz

[@adik9441]

Very excellent video

[@jeremiahogbonnaya7492]

I Love this video thanks 😊👍

[@janaram6118]

can you do a laptop? on how they work and each ic's function?

[@RixtronixLAB]

Nice video , thanks :)

[@huseyindenkalan4]

superb explanation. many many thx.

[@roseelectronics4582]

Nice work!

[@aatifshah8476]

Dear sir, i would request u to plz make more & more circuits i want to design the circuit . if u ll cover the designing ur channel will reach at top & also it ll be helpful to all .. till now very few are showing the designing part of whole circuitry like the way u are showing its awesome i would request please continue .. and try to cover more & more designing of circuits with 3D animation i thank u a lot ... from bottom of my heart ... plz do it sir ...

[@Mulazim.]

Bravo 👏

[@PrakobChannel_01]

Excellebt explained

[@elyeryan8838]

Thanks, maybe flyback power supply next?

[@ExplorerStuff]

Already there - kzbin.info/www/bejne/aH_ChWqMe96gfMk

[@RNA0ROGER]

The h bridge in principal is power limited by using p channel fets

[@ExplorerStuff]

Hence. you can use multiple fets, parallel to each other.

[@Asoallahorputhe1k]

Nice❤❤

[@heerofinalfantasy8514]

ชอบสุดๆ

[@iluxaa9999]

братан, как всегда круто! Если есть техническая возможность, прошу добавить принципиальную схему в описание, чтобы лучше по ним понимать.

[@vivekkumarthakur7190]

If I design it by own will it be efficient ??

[@ExplorerStuff]

I wouldn't recommend building this. This circuit isn't efficient or safe. This video is only for understanding the basics only, building it will be a completely different thing.

[@putraadriansyah8082]

So, basically there are 2 route to build an inverter... 1. I called it single step inverter, the sPWM module drives an H Bridge at low voltage and drives a step up transformer, and from the output of the transformer connected to a feedback circuit.. (12vdc -> 220vac) 2. I call it 2 step inverter. So you have 320v DC supply from a DC to DC converter, and then feed it to H Bridge and then give it sPWM signal.. (12vdc -> 320vdc -> 220vac) and then do the feedback mechanism... The first route is the safest because you're working in low voltage (as long as you dont mess with the high voltage section). But because it's using iron core transformer, this design is the least efficient.. The second route, is quite dangerous and challenging.. you need to make a boost converter first (SG3525/KA7500 maybe?) To get 320vdc or source a ready made converter.. this is dangerous (basically everything above 90v dc is dangerous) and then you feed the 320vdc to a h bridge.. then you give it sPWM signal.. this is the efficient way because you are using switched mode power supply technique and using ferrite core transformer in the dc to dc step up Now for safety, there's a module called the EGS002 sPWM driver board. It's cheap (80k IDR/less than 15usd) and it will do everything for you... Overvolt, overtemp, undervolt, short circuit etc.. Now that I mention the driver board module.. I suggest you not make your own driver.. *do NOT* try to make your own module... It's too dangerous I almost died (literally) because of this experiment. You have been warned

[@hoomansarrafan9843]

why not implement safety features such as temperature monitor, Voltage feedback, Over current protection and such using the microcontroler?

[@Animinetor]

Nice

[@orangteknikc-5574]

Thank's to your video👍

[@NirajKumar-sh4tb]

Please make video on amplifier ics

[@aboh8726]

than you vary mach sar

[@خالدباشميل-ب9و]

please can you give more explain how do OP in inverter and give explain on this by use schematic diagram example for this

[@puwartech7111]

plz explain about buck converter

[@ExplorerStuff]

Already there - kzbin.info/www/bejne/jWexgIlsl52ertU

[@sudheerkumar5966]

Plz make programming vedio on Micro controller and Micro processor.

[@truemanakayombokwa708]

How can I come up with a project

[@pihu3991]

How can we obtain zero voltage

[@pramode-theinventorfromsri4675]

Thank you

[@ridhohidayat9723]

How to build it

[@abubakaryusufabdullahi37]

Thanks

[@smartups1]

In next video add some feed back loop.

[@aiasolarsolution3646]

plz name of software

[@T-Series-scenario]

Dear sir, can I upload your video my fb page.?

[@CannonballCircuit]

do you have a patreon?

[@ExplorerStuff]

Will drop here once made. 😀

[@miladinde]

Excellent, but if you could translate into another tab, for example, Persian Hebrew Russian may see more easily and more interesting and more interesting solutions.

[@lupojacobo9892]

Exelente aplicacion

[@technicalinformationtechno980]

please give you Igbt animation video

[@terlumunjoseph6779]

teach me how to make animations like these

[@hashbrown777]

'to get a sinusoidal output you need a sinusoidal source', I mean you expanded the not-gate into its transistor components, but the most important magic-sauce of the comparator itself and that sine source is left unexplained

[@beanapprentice1687]

You can just use a microcontroller and make it output a pwm signal that changes duty cycle based on a sine function.

[@coucouj2781]

Google Wein Bridge buddy :/

[@prashantmirjapur4772]

Plz upload more videos

[@mdtaher-cv7hj]

❤

[@TanvirKabir0461]

Dear Sir, I have a Chinese inverter of 500 VA, how can I upgrade to 1000va,? Could you please made a video on it. Thanks,,,

[@peterfitzpatrick7032]

The component ratings will be for the 500watts output... you would have to change too much.. better to just sell the present one & buy the larger one... 🤔

[@Atetus94]

❤️

[@opopooopo4621]

Is it possible for anyone to talk to me because I want to improve the language?

[@devdev8194]

All switch are used N chanel

[@harisshaikh8993]

First comment... 😁😁

[@ExplorerStuff]

🎉

[@neerajshetty7846]

@@ExplorerStuff first comment on your comment😉🙃

[@ExplorerStuff]

@@neerajshetty7846 😂👍🤯

[@sg8nj]

I think your from India🇮🇳

[@AIKON2024]

Лайк

[@КириллТок-т5о]

Waiting for Russian subtitles

[@ExplorerStuff]

Added.

[@КириллТок-т5о]

@@ExplorerStuff Thank you dear friend

[@SH-dr2or]

😄😄😄😄

[@piconano]

Why are they called inverters instead of converters? An example of an inverter would take a +5V and output -5V, hence inverting the voltage. These don't invert anything. They convert DC to AC, hence they should be called "converters".

[@ExplorerStuff]

Originally converters were large rotating electromechanical devices used to convert AC to DC. Essentially they combined a synchronous ac motor with a commutator so that the commutator reversed its connections to the ac line exactly twice per cycle. The result is ac-in dc-out (with a lot of switching noise thrown in). If you invert the connections to a converter you put dc in and get ac out. Hence an inverter is an inverted converter.

[@pravindabhade4252]

Sar igbt nbar send

[@kimjoun8222]

Second comment

[@Global-90]

DC mobile charger 12+24v 2.8 ampar

[@dhawlandrashrivastav]

Aisa bhi hota hai😂😂

[@pravindabhade4252]

Sr send me

[@pravindabhade4252]

Price rate

[@vermillion4971]

very hard to grasp it through robotic voice, big dislike

[@rkb6783]

Do you complain about the, Commercials on your channel ? Or... Do you pick them ? Criminal Advertisers ?

[@emmanuelfrimpong4645]

Good evening sir. Please I would like to use some of your information from this video in my report writing. credits will be given to you. I would like to know how I can contact you. Thank you.

[@ExplorerStuff]

You can use it for educational purposes. 👍 Contact details are in about section.

[@estou_aqui-2361]

great video

[@sokullumahmutpasa6651]

thank you

[@MaharashtraTractors]

Nice

[@Global-90]

DC mobile charger 12+24v 2.8 ampar