How to adjust needle bar heights on a Meistergram Embroidery Machine GEM XL-1500

Welcome back! Today we are going to be showing you how to adjust needle bar heights and and when and why they should be adjusted.
SUBSCRIBE!
/ @meistergramembroidery...
FOLLOW US!
Instagram: / meistergramembroidery
Facebook: / meistergram
Twitter: / meistergram
VISIT OUR WEBSITE!
www.meistergram.us
CONTACT US!
1-888-463-4783
[phone]
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
This is why our customers love us:
• Meistergram at West Co...
How to remove the needle case on your Meistergram Embroidery Machine GEM XL-1500:
• How to remove your nee...
How to reinstall your needle case on your Meistergram Embroidery Machine GEM XL-1500:
• How to reinstall your ...
How to assemble a stand for your Meistergram Embroidery Machine GEM XL-1500:
• How to assemble the st...
How to replace the reciprocator on your Meistergram Embroidery Machine GEM XL-1500:
• How to replace the rec...

[@allanjeff4431]

It's ageas I was looking for this adjustment thank you so much

[@claudiuvcampeanu89]

Hello!,do you know anything about E-Lucky’s embroidery machines? I will need some help,if is possible.

[@mazzgaj]

Good job very helpful!

[@paredesrodrigo8694]

me sirvió, muchas gracias. Desde Argentina. I use your video to fix a problem in my machine, thanks a lot.

[@hugogarcia7539]

traducilo q no entiendo un joraca

[@muhidris4757]

Terimakasi atas ilmunya pak semoga bermanfaat

[@kimspencerprimic753]

Awesome video and explanations.. thank you!!!!

[@brendawiedmer2901]

I had a problem with my timing and got that figured out. Now none of my needles will go all the way down. The pressor foot only lowers to about 1-1/2" above the plate. Any suggestions?

[@hugogarcia7539]

Su explicacion es fantastica, se podria hacer videos en Español?

[@neverhadmuch]

Hi. I have machine that very similar to this and wanted to know if you can help?

[@AbdulhadiYakubu-p6s]

Nice one

[@carinabam5833]

One of my needles is hitting the needle plate how do I adjust that

[@oluwatoyinyusuf7804]

Hi if the needle of my machine is not coming out from the down part of the machine,what can I do?

[@maheshundale4710]

The needle point length from the needle eye varies according brands. How can you recommend 6MM as fixed measure in every case?

[@mariodowningmrfitnessfitne5160]

All these machines are the same!

[@robertogarcia9572]

Thanks!!!

[@diarranani8713]

❤❤

[@kamelchikhabelgacem5502]

And how to adjust hook timing with degre ° ??

[@rahilone5556]

[@hassindoembro]

Nice

[@maheshundale4710]

Needle lowest point depends on hook point passing hight level at needle.

[@ruhulaminamin-d6r]

Hi sir

[@TincuLorenzo]

And after you have to change all the needles lol because you hit them with the key

[@HectorGonzalez-uj5nk]

Were merely scratching the surface of the key with the needle. The same is done if you use a guage it will not damage the needle unless your force it.

[@tracyhawksball]

From what I have seen this is how everyone checks the needle depth.

[@TincuLorenzo]

​@@HectorGonzalez-uj5nk no is not true you need 1 millimeter between the needle and the gauge and if you touch the point of the needle 100%sure you will see the bad results on the garment, but it's up to the quality required, if you want a low quality of embroidery it's perfect 😉

[@TincuLorenzo]

​@@tracyhawksball yes is true 180 and 0 degrees are the fixing position, true, what I see that is not correct is the fact that he touched the point of the needle

[@tracyhawksball]

No issues sir.I am new to this machine. Are you familiar with them because I am having a hard time getting it operating correctly. Thread tension is an issue after performing the task that Hector was teaching.

[@ElViveHoy777]

this is not done correctly