how to bend square tube 90 degree angle

[@Richard-kh1uj]

You make "Macgyver" look like a slouch ! Your Amazing. Are you an Alien?

[@asiawelder]

🙏🙏

[@SaleemAhmad-xl2xp]

Shabash ustad shabash

[@asiawelder]

🙏

[@ErwinTunda-an]

is ds a sqr tube or rec tube?

[@asiawelder]

🙏

[@NarutoCrimsonStorm]

what kind of pen do u use

[@asiawelder]

🙏

[@tomthompson7400]

Its a lot of bother to save a very small amount of weld ,,, but you can have a thumbs up as you left the guard on the grinder.

[@哀愁のブルドッグ]

手の汚れだけでも職人さんだと伝わります。

[@romeovasquez329]

Very good job

[@asiawelder]

🙏🙏

[@trinhphan6075]

Góc 90 độ

[@sudalaimani1653]

Good job bro I am from India

[@asiawelder]

Thanks bro i m from in indonesia 🙏

[@sharkins8696]

I like that you made the video feel like i was there with my ear up against the grinder, the deafening audio blowout was great!

[@asiawelder]

Thanks 🙏

[@asiawelder]

Please like & share my video sir 🙏🙏

[@shurikkupitman5407]

Это конечно весело. Но если вы не заметили, эта штука, перестала быть трубой. К чему тогда, весь геморрой? Можно просто приварить два профиля, друг к другу, под углом.

[@dirceumachado3772]

Estalar eu sei me ensina se o rolamento estragar como substituir ou este rolamento é furada

[@nkwelder1386]

Sangat hebat

[@asiawelder]

🙏🙏🙏

[@BENGLASBERKAHCHANNEL]

Hadir nyimak aktivitas anda yang sangat penting bagi saya...❤❤

[@asiawelder]

🙏🙏🙏👍

[@asiawelder]

Cm salah beri ukuran,yg 10 cm harusnya 6 cm 🙏

[@Gersela.channel]

👍👍👍

[@asiawelder]

🙏🙏💐

[@andrzejmacur585]

Praca bez sensu.

[@sergej_vasilich]

Маркер у тебя чёткий

[@asiawelder]

🙏🙏

[@alex7705]

Super 👍🏻

[@FabricationWeldingmetal]

Please pipe size

[@edgargad2941]

Looks like 1"x 3" or 1 1/4"x 3". The wall thickness is close to 1/16"

[@richardslater677]

I’ve obviously missed something here! When the pipe is bent to 90degrees, it is blocked, ie the open side butts up to the closed side. Therefore, there is no way for anything to flow or inserted through the pipe. Maybe that’s what is supposed to happen?

[@alphagt62]

I suppose you could drill a hole in the right spot so it would wind up in the middle of the corner. But I guess most times it would just be structural with no wires or hoses.

[@jeramyhiggins7661]

Maybe it’s not meant for flowing liquids. Maybe it’s structural framing.

[@Spiritof_76]

Rectangular tubing is rarely used to carry fluids. That's usually reserved for round pipes.

[@circasurpriseme]

Please wear gloves . I had to pause the video

[@asiawelder]

🙏

[@manahiro4758]

思った完成形と違った😅

[@逃げ回る斎てい逃彦]

パーフェクト

[@KoAye-b9q]

❤

[@asiawelder]

🙏💐♥️

[@romilsonsoares1199]

Top

[@asiawelder]

🙏

[@VLVIC]

Это называется: когда коту делать не...

[@asiawelder]

🙏

[@DerekWalsh-l4i]

But you haven't bent it to a 90 degree angle. You have bent it to two 45 degree angles.

[@edgargad2941]

His two runs intersect at a 90° angle.

[@DerekWalsh-l4i]

@@edgargad2941 I agree, but that is not what the title says. It says "how to bend square tube 90 degree angle" and he has not done that.

[@juanperezyperez9530]

Es imposible, si el ancho del perfil es de 10 cm., al trazar una diagonal debe ser más de esa medida y no los 8.5 que muestra, chequenlo y si estoy mal me corrigen.

[@claudiochiesa8809]

Ci avevo pensato anch'io.

[@МансурГайсин-ь5м]

У меня мозг сломался.

[@PatBarrett2663]

And that tube ain’t square buckwheat!

[@edgargad2941]

Damn straight, that's a rectangle.

[@funkyjunky6574]

Said bend not cut

[@asiawelder]

🙏

[@jorgearun3625]

Eso no es un tubo cuadrado bestia

[@ВладимирПоспелов-п3у]

10 см размер не адекватный

[@asiawelder]

🙏

[@toratorasurf136]

10cmじゃないやろ！

[@asiawelder]

🙏👍

[@Garik_Vorota]

Не кто не будет платить за медленную работу. Вы хоть на штаны зарабатываете?

[@yamasatoma]

あ、そっち方向にね。

[@ЕвгенийС-т5п]

Геморрой какой-то 😢

[@trevordecker4872]

What's with the stupid sounds

[@asiawelder]

🙏🙏