How to bind Honeywell CM61ng to the HC60NG

How to tutorial on binding a Honeywell Cm61 thermostat to the receiver HC60NG
After having this problem and not finding a tutorial in english here it is guys hope it helps.
💥💥💥💥💥💥💥💥💥💥😍
Quick edit once you get the fast flash and it returns to a steady flash that’s when the pairing will work you don’t need to press the button again as it activates a green light if the green light is active it won’t pair. Thank guys and thumbs up if it worked :)

[@Ilovepandas12321]

Great tutorial. For days I couldn't work it out. Works perfectly now. Thank you.

[@robbeard6929]

The binding operation described below is required if: - any of the system components (room unit or relay box) are replaced - HC60NG has incorrect or no binding data stored (e.g. when pre-bound system pack components have been mismatched) During the binding procedure keep approximately 1m distance between the room unit and the relay box. 1. Press and hold the HC60NG push button for 15 sec to reset previously stored data. The red LED will start to fl ash at 0.1 s on/0.9 s off. Release the push button. 2. Press and hold the HC60NG push button for 5 sec to enter the binding mode. Red LED fl ashing at 0.5s on/0.5 s off confi rms the binding mode has been entered. 3. Move the CM67NG slider to the OFF position (for CM61NG push the OFF button) and press the TEMP , and PROG 1 buttons together 4. Press the button to send the binding signal. The red LED is switched off to confi rm successful binding operation. If red LED still fl ashes push the button again until binding is successful. 5. Follow the START UP and other procedures to commission the single zone RF system.

[@hickey3162]

Thanks for this video mate, you've shown me how to sort my problem out, everything paired and working now 🙏🏻

[@PolymathTheDiver]

Thanks. Me and the wife were suffering from a run away boiler, and having to sit around in pants as the house was trying to rival mexico. This video helped us out. Thanks!

[@R4YLA]

Good to hear pal , All the best :)

[@colinfurniss2915]

Hey works a treat thanks good work

[@Sum_Ting_Wong]

Perfect. Worked a treat mate. Thank you very much.

[@geordieoneill1245]

Watch the video bang with in 2 second.s its paired working like new cheers

[@lifeits3lf]

Stupid thing but can you make a video of how to turn it on? It shut off randomly and i even changed the batteries with new ones but it wont go on

[@bobbyhayday6022]

After holding the button for 15 seconds then releasing and pressing again I get a green light that stays on (top one) and a flashing red light (second one), then when I get the thermostat to inst mode and press the 'i' button nothing happens, getting so frustrated now 😐

[@R4YLA]

Just follow the vid buddy works Everytime

[@R4YLA]

Should do it without a green light then works

[@hobiburhabzrohman.4340]

Hi mate I just wanted know how do I keep my hearing on instead of turning it off when the house is really hot I don’t know how to do it on my Honeywell cm61ng please help me thanks

[@R4YLA]

Hobibur Habz Rohman. Hey select man turn temp up to 30 degrees should stay on

[@hobiburhabzrohman.4340]

Yeh it’s working like that but when how do I set up for early morning auto start

[@rezahasnagaear7006]

Hi can u plz show me how to set up the temprtue Monday to Friday plz if u send video is gd help thanks

[@hassaan9446]

Bro I followed the steps u mentioned and after it says IN ST on the thermostat nothing happens. After I press the i button nothing happens although IN ST is displayed on the thermostat

[@R4YLA]

Iman Hidayat hopefully it’s all sorted bro, it will pair once there is a steady light....

[@lianabuhagiar8764]

How to program Cm61ng

[@R4YLA]

If it's the same as mine to bind it just follow the vid thanks

[@arshadmahmood6549]

Sorry mate your information was not all correct you need to press continually for 15 sec then let go for two secs then press again till blinks slowly then follow your instructions

[@R4YLA]

Glad it worked for you 🙂